PORSCHE 964 BACK UP
Can't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.
From $58.86
Make a selection
Say good bye to the days of having to weld and cut aftermarket sport cats to make them fit! We have our sport cats made in Germany to our specifications and that means that these are 100% bolt on without issue! - + 12 crank hp & +8 crank torque. - 100 cell, tri metallic German hjs sport catalysts. - large volume o 105 mm (4.1 inch diameter) high flow cat. - exhaust hanger brackets are included so that the heat shield does not have to be removed. - weighs 7.2 lbs. (3,2 kg). - direct bolt on replacement. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - reduces backpressure and thermal stress. - made in Germany. - more distinguished flat 6 growl at wide open throttle. The FVD 100 cell...(choose a part on the right to read more)
General Fitment 911 1989-94
From $1,481.44
Make a selection
Say good bye to the days of having to weld and cut aftermarket sport cats to make them fit! We have our sport cats made in Germany to our specifications and that means that these are 100% bolt on without issue! - + 10 crank hp & +6 crank torque. - 200 cell, tri metallic German hjs sport catalysts. - large volume o 105 mm (4.1 inch diameter) high flow cat. - exhaust hanger brackets are included so that the heat shield does not have to be removed. - weighs 7.2 lbs. (3,2 kg). - direct bolt on replacement. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - reduces backpressure and thermal stress. - made in Germany. - more distinguished flat 6 growl at wide open throttle. The FVD 200 cell...(choose a part on the right to read more)
$1,721.41
Make a selection
Stoptech rear 13 inch 4 piston big brake kit Porsche 964 Carrera 91-94
Stoptech big brake kits give your vehicle that supercar look and feel, and exceed stock brake system performance in two areas. First, larger rotors increase heat capacity. A brake system?s biggest enemy is heat. A brake system with inadequate heat capacity will overheat leading to brake fade, increased stopping distances, and possible failure. Second, stiffer calipers and stainless steel lines reduce system compliance and increase initial bite and pedal feedback. The key is to increase heat capacity and reduce compliance without upsetting the stock front to rear brake torque ratio. If the brake upgrade you select adds too much front t...(choose a part on the right to read more)
General Fitment 911 1989-94
$2,910.17
Make a selection
Material: 11 gauge, type 304, stainless steel.
Finish: powdercoated in durable black wrinkle-finish.
Weight: 4 lbs.
Models: model 846r9080 secures Porsche model recaro spg xl to floor on driver's side.
Installation: adapts GT3 seats to 944,964,965,993 for direct floor mount
Miscellaneous: allows taller drivers to floor mount seats for meeting their clearance requirements. May be mounted in three positions with two inches of total adjustability forward - back. 846r9042 adapter is required for installation. R-908x series seat mount kits provide an inboard seat belt mount. 846r9031 optional anti-sub strap mount for 846r908x series.
Fits: GT2 (96-98), turbo (95-98), cup-race (94-98), rsr (96-97), rs (95-...(choose a part on the right to read more)
General Fitment 911 1994-98 911 1989-94 944 1982-85 944 1985-88
Product details:
Replaces the heavy and restrictive factory muffler system with a straight-through design to reduce weight, improve sound, and increase power
Features:
-fits all Porsche 964 c2, c4, rs america, euro rs and speedster vehicles 1989-1994
-increases power and improves throttle response
-saves 25 lbs from the rear of the vehicle
-more aggressive ton compared to the maxflo muffler system that is oriented for a track vehicle or auto-x
-designed to replicate the Porsche motorsport 964 cup primary & secondary muffler bypass pipes
-constructed from high-quality 14-16 gauge cnc mandrel-bent t304l stainless steel for optimum...(choose a part on the right to read more)
General Fitment 911 1989-94
From $426.60
Make a selection
This pipe connects to the oil filter console 96420702503 and to 96420725711. It acts as a backflow line from the oil filter. We recommend replacing the heat shielding wrap, part # 96420735200 when installing this pipe. This part is sourced in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.
View/Change Diagram
From $226.80
Make a selection
Stoptech front 14 inch 4 piston big brake kit Porsche 964 Carrera 91-94
Stoptech big brake kits give your vehicle that supercar look and feel, and exceed stock brake system performance in two areas. First, larger rotors increase heat capacity. A brake system?s biggest enemy is heat. A brake system with inadequate heat capacity will overheat leading to brake fade, increased stopping distances, and possible failure. Second, stiffer calipers and stainless steel lines reduce system compliance and increase initial bite and pedal feedback. The key is to increase heat capacity and reduce compliance without upsetting the stock front to rear brake torque ratio. If the brake upgrade you select adds too much front ...(choose a part on the right to read more)
General Fitment 911 1989-94
$3,376.73
Make a selection
Material: typ 304, aus rostfreiem stahl.
Oberfläche: pulverbeschichtet in schwarz
Gewicht: 4 lbs.
Modelle: modell 846r9080 ermöglicht den einbau des Porsche GT3 sitzes auf der fahrerseite. Modell 846r9081-ermöglicht den einbau des Porsche GT3 sitzes auf der beifahrerseite
Installation: für den einbau der GT3 sitze in 996/997/Boxster für direkte boden-montage wird noch zusätzlich 846r9042( adapter) benötigt.
Material: 11 gauge, type 304, stainless steel.
Finish: powdercoated in durable black wrinkle-finish.
Weight: 4 lbs.
Models: model 846r9080 secures Porsche model GT3 seats to floor on driver's side. Model 846r9081 secures Porsche mode GT3 seats to floor on passenger's side.
Installation:...(choose a part on the right to read more)
General Fitment 911 1994-98 911 1989-94 944 1982-85 944 1985-88
Product details:
Improved sports car sound; deep and throaty while maintaining street appropriate volume
Features:
-fits all Porsche 964 c2, c4, rs america, euro rs and speedster vehicles 1989-1994
-increased throttle response throughout the rpm range with less restrictive mufflers
-available in either a single or dual outlet configuration
Note: requires slight modification to the factory rear bumper for proper fitment of the second outlet
-constructed from high-quality 14-16 gauge cnc mandrel-bent t304l stainless steel for optimum flow and maximum durability
-direct bolt-on replacement for the restrictive factory mu...(choose a part on the right to read more)
General Fitment 911 1989-94
From $1,290.60
Make a selection
Features:
Fits: all 964 c2/c4/rs america products 1989-1994
copper gaskets included.
+12hp & more torque.
high quality t304 stainless steel mirror polished showcar shine
o2 sensor bung so your 964 fuel injection system can automatically adjust mixture/idle/part throttle for maximum performance.
just like Porsche factory German catbypass euro-premuffler but without the $700.00 price.
looks like a stock catalytic converter--best way to pass a visual exam inspection but the system straight "see through" with an internal muffler inside.
simple and easy bolt on installation.
quieter and more durable than a mild steel straight pipe yet you can still roll a golf ball thru ...(choose a part on the right to read more)
General Fitment 911 1989-94
From $534.60
Make a selection
Product details:
Replaces blower motor assembly and ductwork while allowing plenty of heat; replicated from factory rs part
Features:
-fits all 964 Carrera vehicles (1989-1994)
-saves 8 lbs from rear of vehicle
-replica of the Porsche rs lightweight factory heat duct
-factory Porsche part is roto-formed plastic with parting lines where as the fabspeed rs heater pipe is genuine carbon fiber.
-replaces blower motor assembly/ductwork and still allows heat in the cabin.
-improves aesthetic value with clear coated carbon fiber tube.
-easy 20 minute diy install
-all fabspeed performance products are backed by the fabspeed lifetime limited warra...(choose a part on the right to read more)
General Fitment 911 1989-94
If your outer tie rods are worn you will experience sloppy steering response and knocking / creaking sounds. Your outer tie rods keep the steering centered, so failure can be very dangerous and can seriously affect steering control. Prevent that from happening by replacing them as quickly as possible with our genuine replacement inner tie rods. Once you do, you will experience tighter, more precise feedback without noise. Complete kit consists of: 1 qty. Tie rod 1 qty. Hexagon nut (m14 x 1.5) 1 qty. Ball joint end 1 qty. Lock nut & pin sold individually. Left or right side fitment. 2 qty. Required. Tech tip: replace the inner tie rods also for a new car steering feel ! Purchase our part # 96434705804 & 96434719...(choose a part on the right to read more)
View/Change Diagram
From $59.71
Make a selection
Product details:
Replaces blower motor assembly and ductwork. Perfect for summertime drivers education and club race cars
Features:
-fits all Porsche 964 Carrera vehicles (1989-1994)
-saves 10 lbs from rear of vehicle
-exact replica as used by the Porsche motorsports for factory lightweight 964 cup and 964 rsr race cars.
-replaces blower motor assembly and ductwork.
-cleans up engine bay for easier access
-simple diy installation
-all fabspeed performance products are backed by the fabspeed lifetime limited warranty
General Fitment 911 1989-94
From $91.80
Make a selection
Product details:
Replaces blower motor assembly and ductwork while still allowing plenty of heat, just like the factory rs part
Features:
-fits all Porsche 993 vehicles (1994-1998)
-saves 9 lbs from the rear of the car
-full carbon fiber construction
-simple diy installation
-this a replica of the Porsche Germany rs lightweight factory heat duct that was used on all 3.6 liter special rs lightweight race cars.
-all fabspeed performance products are backed by the fabspeed lifetime limited warranty
Note:
All late model 993's, 1996-1998 require the Porsche factory 964 fan shroud, part # 96410640302
General Fitment 911 1994-98
Rennline's stainless steel folding race hook install in minutes on any Porsche with factory screw type removable tow hook. Unlike the aluminum units on the market that are usually advertised as "for decorative purposes only", rennline's stainless steel tow hook is a precision machined and will stand up to the extreme abuse seen in any race environment. With a 2" opening as required by most organized race events and screw directly into the factory bumper pull location. Each hook comes with a rubber bumper to be applied on the back side to insure your bumper cover will never get scratched from hook contact. Keep the corner workers and track officials happy by installing a hook that are highly visible and h...(choose a part on the right to read more)
Product details:
Loud & aggressive sports car sound with adjustable single or dual outlets
Features:
-fits all Porsche 964 c2, c4, rs america, euro rs and speedster vehicles 1989-199
-increases horsepower and torque by 24 whp and 21 ft-lbs without optional sport cats expect a great increase in power when including them.
-loud & aggressive sports car sound. Recommended for aggressive street and track usage.
-rsr-style 1 piece equal length mandrel-bent header tubes with f1 style high velocity 3-into-1 pyramidal investment cast merge collectors.
-constructed from 14-16 gauge t304l stainless steel
-dual outlet muffler system comes with all r...(choose a part on the right to read more)
General Fitment 911 1989-94
From $3,018.60
Make a selection
Product details:
Stainless steel outlet tip replaces the factory right-side outlet for a sportier look and finish; available in polished chrome finish
Features:
-fits all 964 Carrera vehicles (1989-1994)
-available in polished chrome
-compatible with the OEM muffler only
-simple diy installation with no cutting or welding required
-all fabspeed performance products are backed by the fabspeed lifetime limited warranty
General Fitment 911 1989-94
From $243.00
Make a selection
Product details:
Loud & aggressive sports car sound with adjustable single or dual outlets
Features:
-fits all Porsche 964 c2, c4, rs america, euro rs and speedster vehicles 1989-199
-increases horsepower and torque by 24 whp and 21 ft-lbs without optional sport cats expect a great increase in power when including them.
-loud & aggressive sports car sound. Recommended for aggressive street and track usage.
-rsr-style 1 piece equal length mandrel-bent header tubes with f1 style high velocity 3-into-1 pyramidal investment cast merge collectors.
-constructed from 14-16 gauge t304l stainless steel
-dual outlet muffler system comes with all r...(choose a part on the right to read more)
General Fitment 911 1989-94
From $2,802.60
Make a selection
Product details:
The ultimate light weight aluminum strut bar reproduced exactly as used by the Porsche motorsport ag on the 800 hp 993 tt GT2 evo
Features:
-fits all Porsche 964 Carrera vehicles (1989-1994)
-accurate reproduction of Porsche motorsport 993 GT2 evo strut bar
-stiffens front suspension for improved handling and turn-in
-direct bolt-on installation, no cutting or welding required
-all fabspeed performance products are backed by the fabspeed lifetime limited warranty
General Fitment 911 1989-94
Product details:
High-flowing, direct bolt-on replacement for the bulky & restrictive factory catalytic converter
Features:
-fits all Porsche 964 c2, c4, rs america, euro rs and speedster vehicles 1989-1994
-increases horsepower and torque by 24 whp and 16 ft-lbs for greatly improved throttle response
-less back pressure and improved throttle response
-constructed from 14-16 gauge, t304l c.n.c. Mandrel bent stainless steel
-includes German imported 200-cell tri-metallic sport catalytic converter with integrated o2 sensor bung
-direct bolt-on replacement with no cutting or welding required.
-all fabspeed performance products are ...(choose a part on the right to read more)
General Fitment 911 1989-94
From $750.60
Make a selection
Product details:
Reduces weight, increases power, and improves sound by replacing the heavy and restrictive secondary muffler with a straight-through pipe
Features:
-fits all Porsche 964 Carrera vehicles (1989-1994)
-increases power and improves throttle response
-reduces weight in the rear of the vehicle
-more aggressive tone compared to the maxflo muffler system
-constructed from high-quality 14-16 gauge cnc mandrel-bent t304l stainless steel for optimum flow and maximum durability
-direct replacement for the OEM secondary muffler
-all fabspeed performance products are backed by the fabspeed lifetime limited warranty
General Fitment 911 1989-94
Product details:
Loud & aggressive sports car sound with adjustable single or dual outlets
Features:
-fits all Porsche 964 c2, c4, rs america, euro rs and speedster vehicles 1989-1994
-increases horsepower and torque by 24 whp and 21 ft-lbs without optional sport cats expect a great increase in power when including them.
-loud & aggressive sports car sound. Recommended for aggressive street and track usage.
-rsr-style 1 piece equal length mandrel-bent header tubes with f1 style high velocity 3-into-1 pyramidal investment cast merge collectors.
-constructed from 14-16 gauge t304l stainless steel
-dual outlet muffler system comes with all ...(choose a part on the right to read more)
General Fitment 911 1989-94
From $4,098.60
Make a selection
Product details:
Loud & aggressive sports car sound with adjustable single or dual outlets
Features:
-fits all Porsche 964 c2, c4, rs america, euro rs and speedster vehicles 1989-199
-increases horsepower and torque by 24 whp and 21 ft-lbs without optional sport cats expect a great increase in power when including them.
-loud & aggressive sports car sound. Recommended for aggressive street and track usage.
-rsr-style 1 piece equal length mandrel-bent header tubes with f1 style high velocity 3-into-1 pyramidal investment cast merge collectors.
-constructed from 14-16 gauge t304l stainless steel
-dual outlet muffler system comes with all r...(choose a part on the right to read more)
General Fitment 911 1989-94
From $4,098.60
Make a selection
Product details:
This product takes 2-3 weeks to fabricate.
Direct bolt-on replacement upgrade for the factory exhaust tips; improves flow and enhances the vehicle's aesthetic
Features:
-fits all Porsche 964 turbo 965 vehicles (1990-1994)
-improves exhaust flow and sound by replacing the restrictive factory tips (pictured here) with a clean straight-through design
-angle-cut 4.5" oval shape
-polished to a mirror finish
-constructed from high-quality 14-16 gauge c.n.c. Mandrel-bent t304l stainless steel
-simple diy bolt-on installation
-all fabspeed performance products are backed by the fabspeed lifetime ...(choose a part on the right to read more)
General Fitment 911 1989-94
© 2024 Automobile Atlanta Inc.
505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844
|