PORSCHE 997 EXHAUST AND MUFFLERCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: CAYMAN 2009-12 - Uncategorized (includes uncategorized and accessory items) BES99125020SK No need for Porsche sport exhaust (pse) envy with this muffler! This offers weight savings and a far more exotic sound than the pse, all without drone. It is the perfect compromise for you and your loved ones. Rich, deep, turbo motorsport tones with the valves open and soft subtle, completely stock sounds with them closed. Top of the line or range depending on the english and is the best choice for a daily driver. Features: - + 16 crank hp & + 15 crank torque. - weighs 37 lbs. (17 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - direct bolt on replacement for the factory center muffler. - includes necessary installation hardware. - reduces turbo lag, backpressure and thermal lo...(choose a part on the right to read more)
$5,275.91
Make a selection
$831.60
Make a selection BES99125010S
$2,737.15
Make a selection
$874.22
Make a selection BBI9912020003 The bbi autosport 997 & 991 GT3 / rs exhaust side bypass is a direct replacement for the factory primary side mufflers. The primary mufflers are weigh approximately 44 pounds total while the bbi pipes are 4 pounds in comparison. For durability and protection against corrosion, each system is meticulously tig welded using 304 aerospace grade stainless tubing with lower carbon content. The result is a substantial reduction in weight behind the rear axle which significantly improves handling and less restriction to produce a much more aggressive exhaust note.
$1,026.00
Make a selection 210111011D1 Improve sound and performance by decreasing exhaust backpressure with this catalytic bypass pipe. This is a painted steel bypass pipe, manufactured by dansk. They offer a complete line of tuning and performance parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment manufacturers (oem) to Porsche in Germany. - + 10 crank hp. - lower, deeper, more exotic exhaust note. - steel coated with high temperature paint. - made in europe by dansk. - reduces back pressure and thermal load on the engine. - includes o2 sensor bung....(choose a part on the right to read more)
$331.45
Make a selection 100211021SSI This heat exchanger is engineered for the discerning Porsche 911 owner. Ssi heat exchangers are made from superior t 304 grade (18% cr, 8%+ ni) stainless steel. Ssi has become an industry standard for Porsche 911 heat exchangers due to the exceptional materials, craftsmanship and durability. This is critical when considering heat exchangers, as exhaust leaks caused by poor materials can lead to carbon monoxide entering the cabin via the heating system. Features: gains of +10-15 hp and +10-20 tq t304 stainless steel (18% cr, 8%+ ni) increased pipe diameter for backpressure reduction connects to "early style" dual inlet mufflers bolt on replacements reduces the thermal load on the motor includes custom torque w...(choose a part on the right to read more)
$3,407.18
Make a selection 100211022SSI This heat exchanger is engineered for the discerning Porsche 911 owner. Ssi heat exchangers are made from superior t 304 grade (18% cr, 8%+ ni) stainless steel. Ssi has become an industry standard for Porsche 911 heat exchangers due to the exceptional materials, craftsmanship and durability. This is critical when considering heat exchangers, as exhaust leaks caused by poor materials can lead to carbon monoxide entering the cabin via the heating system. Features: gains of +10-15 hp and +10-20 tq t304 stainless steel (18% cr, 8%+ ni) increased pipe diameter for backpressure reduction connects to "early style" dual inlet mufflers bolt on replacements reduces the thermal load on the motor includes custom torque w...(choose a part on the right to read more)
$3,768.34
Make a selection 100211025SSUSA If you have a us model 1980-83 911 SC and are looking to replace your heat exchangers we have some good and bad news. The original heat exchangers (part # 930 211 025 02) are no longer available from Porsche. But, these stainless-steel industries (ssi) heat exchangers will work with modifications. The good news is, once done, you will have more torque and horsepower! Free flow conversion heat exchangers improve sound and performance, while reducing backpressure and thermal load on the motor. These are based off the early style exhausts found on the 1974 2.7 l rs. Those models had a straight through, superior, free flow exhaust design that included a dual inlet muffler. When converting to these heat exchangers y...(choose a part on the right to read more)
$3,435.70
Make a selection 22011098100 FVD Brombacherhas a long tradition of offering high quality, extensively tested, easily installed tuning products that offer proven performance. Those high standards naturally led us to the innovative pro design (ipd) plenum product. The ipd patented cast aluminum intake plenum with the larger 82 mm (gt3) throttle body (competition plenum) increases horsepower and torque by optimizing and increasing airflow into the intake manifold. But in order to capitalize on all the performance gains the ipd competition plenum can deliver, you must strike a balance with exhaust components and software. You cannot simply add the ipd competition plenum on the 981 series and expect large gains. But, no need to worry, the FVD ...(choose a part on the right to read more)
$1,651.32
Make a selection 21011196538 This sport muffler is engineered for the discerning Porsche 965 turbo owner who is interested in pure unbridled power and sound. It is hand made from t 321 grade stainless steel. All piping is mandrel bent for reduced backpressure and increased performance. The sport muffler exudes a lower, deeper linear-firing-order dominated flat 6 Porsche turbo sound with added turbo whistle. Exhaust tips are 76 mm (3 inch) polished ovals with a rolled lip. Each kit includes complete installation hardware, wastegate pipe and clamps. Features: gains of up to 10 hp more* t 321 stainless steel mandrel bent new wastegate pipe new gaskets new hardware new muffler clamps *dependent upon boost level and other modifications. Sold in...(choose a part on the right to read more)
$2,297.61
Make a selection 100211030SSI This heat exchanger kit is engineered for the discerning Porsche 911 3.2 l owner. Ssi heat exchangers are made from superior t 304 grade (18% cr, 8%+ ni) stainless steel. Ssi has become an industry standard for Porsche 911 heat exchangers due to the exceptional materials, craftsmanship and durability. This is critical when considering heat exchangers, as exhaust leaks caused by poor materials can lead to carbon monoxide entering the cabin via the heating system. Features: gains of +10-15 hp and +10-20 tq t304 stainless steel (18% cr, 8%+ ni) 1.5" pipe diameter for backpressure reduction 21.5 mm thick flange with "fire ring" includes o2 sensor socket connects "early style" dual inlet mufflers bolt on replac...(choose a part on the right to read more)
$3,492.72
Make a selection 220110981001 FVD Brombacherhas a long tradition of offering high quality, extensively tested, easily installed tuning products that offer proven performance. Those high standards naturally led us to the innovative pro design (ipd) plenum product. The ipd patented cast aluminum intake plenum with the larger 82 mm (gt3) throttle body (competition plenum) increases horsepower and torque by optimizing and increasing airflow into the intake manifold. But in order to capitalize on all the performance gains the ipd competition plenum can deliver, you must strike a balance with exhaust components and software. You cannot simply add the ipd competition plenum on the 981 series and expect large gains. But, no need to worry, the FVD ...(choose a part on the right to read more)
$1,597.86
Make a selection 21011125PSE Only for vehicles with Porsche standard sports exhaust system 200 cell, hjs tri-metal, hf (high flow) hjs catalytic cores with "u-torque" design, manufactured by m in Germany. The u-torque design compensates for the backpressure loss while running the high flow cats. The design minimizes the loss of low end torque and adds 10-15 ft-lbs of torque in the mid and top range of the rpms. Why settle for the traditional cross over cat design when you can add more torque in the mid-range and minimize the loss of torque down low where the 997's need it most! Please note: these fit the OEM mufflers and Porsche sport exhaust (pse) mufflers. Tech tip:add one of our installation kits FVD mk 997300
$3,575.88
Make a selection BES91105000SST This muffler was specifically designed for a backdate to the st look. It is manufactured for mid-range and top end performance, all without drone inside the cabin. It seamlessly mates to ssi heat exchangers for added performance while keeping the cabin warm in the winter. The muffler is vastly different than the common baffle plated mufflers stuffed with packing material that are common in the aftermarket. Ours are uniquely made with double perforated sound absorption tubes based on the halbgegenstromprinzip (half counter current principle). The acoustic silencer absorption tubes are made in a trapezoidal pattern and are perforated with varying diameters, which isolate and dampen the unwanted frequencies that c...(choose a part on the right to read more)
$2,771.60
Make a selection BBI9912020001 The bbi autosport Porsche 991 GT3 exhaust center section is a direct replacement for the secondary center muffler. For those who desire a slightly milder exhaust tune, this piece is a great alternative to our cup-style side muffler bypass pipes. By retaining stock side mufflers and valves, the factory "sports button" feature is kept to conveniently switch back and forth between the aggressive "sport" mode during spirited driving sessions and the quieter, more civil "non-sport" mode for minimal noise on the highway.
$2,268.00
Make a selection 91111124503EQ Is your exhaust tip a little old and unappealing to look at? Update it with this durable chrome plated stainless tip. This is a direct replacement for original part numbers, 901 111 245 00 and 901 111 245 01 and fits models up to 1989 with 60 mm (2.3 inches) diameter muffler exit pipes. T304 stainless steel. Chrome plated. 70 mm (2 3/4 inch) outer diameter. Original design and look. Slip on, does not require welding. Quality tuning part manufactured by dansk. They offer a complete line of replacement parts and tuning parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This ...(choose a part on the right to read more)
$47.52
Make a selection BES99107060S The perfect addition for an aggressive exhaust note with the added benefit of reduced weight. Features: 2 1/2 (63.5mm) tubing. Weighs 8.3 lbs. (3,7 kg), 10 + lbs. Savings over stock GT3 center muffler. Made of German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. Fits 991.1 and 991.2 GT3 & GT3 rs models.- reuse's factory tips. Includes all necessary clamps and mounting brackets. Made in Germany by m&m exhaust, gmbh. Intoxicating growl at idle, partial throttle and wide-open throttle. No interior resonance or drone. Ecu software is not necessary. Does not alter emissions, 50 state legal in the u.s. Our entire "brombacher" line of exhausts is manufactured by m&m exhaust, gmbh in Germany. T...(choose a part on the right to read more)
$2,498.36
Make a selection BES96405000S1 This muffler produces a glorious flat six race car with low deep tones that reminds us of the 964 cup. It is manufactured in Germany by m&m exhaust, gmbh. This muffler is ideal for anyone who wants a lower deeper tone with more decibels, whether they are just replacing the side muffler or are running cat bypass, sport cats or a cup pipe. + 14 hp (10 kw) & + 15 tq (20 nm) gain. - 2 3/4 tubing (70mm). - weighs 13.8 lbs (6.3 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - absolutely no drone in the cabin. - does not interfere with emissions. - includes factory style hangars and new aero quip style clamps for simple installation. We recommend replacing your exhaust tip with this u...(choose a part on the right to read more)
$1,553.90
Make a selection BES95B05040SK + 15 hp & + 18 tq gain. - 2.5 tubing (63.5mm). - 4 x 4 (101mm) round tips. - 8.5 lb. Weight savings over OEM mufflers. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - electronic valve controller must be removed from the OEM unit and added to our muffler. - made in Germany. Please note: this muffler is a direct replacement the macan turbo (95b) model which comes with a single electronic exhaust valve on the passenger side. This is the very 1st aftermarket muffler for the macan 95b turbo that includes a valve like the factory system. This allows our system ...(choose a part on the right to read more)
$4,907.63
Make a selection BES91105000S This muffler was specifically designed for a backdate to the st look. It is manufactured for mid-range and top end performance, all without drone inside the cabin. It seamlessly mates to ssi heat exchangers for added performance while keeping the cabin warm in the winter. The muffler is vastly different than the common baffle plated mufflers stuffed with packing material that are common in the aftermarket. Ours are uniquely made with double perforated sound absorption tubes based on the halbgegenstromprinzip (half counter current principle). The acoustic silencer absorption tubes are made in a trapezoidal pattern and are perforated with varying diameters, which isolate and dampen the unwanted frequencies that c...(choose a part on the right to read more)
$2,838.13
Make a selection BES97003040S M&m exhaust develops and produces exhaust pipes, catalysts and complete exhaust systems for street and race exotic and sports cars. m&m exhaust specifically concentrates on maintaining original equipment levels of fitment and finish.
$3,152.95
Make a selection 477253121B This is the front muffler for all 76-85 Porsche 924 models. It was original equipment before the cat and will replace it as well. great for the extra performance and quiet exhaust you expect from your 924.
From $121.18
Make a selection BES987C02F0S "brombacher" 987-2/s (sound version) stainless steel exhaust system
$8,014.25
Make a selection BES97003080S1 M&m exhaust develops and produces exhaust pipes, catalysts and complete exhaust systems for street and race exotic and sports cars. m&m exhaust specifically concentrates on maintaining original equipment levels of fitment and finish.
$1,582.42
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |