Vehicles
Sections
76 not categorized PORSCHE 356 B IMS BEARINGCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: BOXSTER 2005-08 (includes uncategorized and accessory items) 106084 There are not many warning signs of an impending ims failure short of a “death rattle” that occurs as the bearing fails and comes apart. These kits replace the factory sealed bearing with a new, severe duty custom ceramic hybrid roller ball bearing for reduced friction and superior performance in poorly lubricated operating conditions and replaces the factory ims flange hub, bearing support, and fastener with a stronger, revised billet chromoly assembly. The center bearing support also receives an increase in size and no longer is cut for the o-ring that keep engine oil from leaking out of the engine - we have relocated the o-ring to the ims hub flange for added strength to the center stud & bearing support...(choose a part on the right to read more) General FitmentBOXSTER 2005-08BOXSTER 1997-04 911 1998-05 911 1987-89
$971.99
Make a selection 106082 There are not many warning signs of an impending ims failure short of a “death rattle” that occurs as the bearing fails and comes apart. These kits replace the factory sealed bearing with a new, severe duty custom ceramic hybrid roller ball bearing for reduced friction and superior performance in poorly lubricated operating conditions and replaces the factory ims flange hub, bearing support, and fastener with a stronger, revised billet chromoly assembly. The center bearing support also receives an increase in size and no longer is cut for the o-ring that keep engine oil from leaking out of the engine - we have relocated the o-ring to the ims hub flange for added strength to the center stud & bearing support...(choose a part on the right to read more) General FitmentBOXSTER 2005-08BOXSTER 1997-04 911 1998-05
$736.50
Make a selection 10610 Billet aluminum ims to crankshaft chain guide/tensioner, replacement for Porsche part no. 996 105 165 55, to help prevent catastrophic engine failures like this. Shown below is a comparison of our billet tensioner paddle compared to the cast factory tensioner. Billet construction provides a significantly stronger and more durable product while utilizing oe Porsche wear pad and pressure pin (both of which are included as shown). Update: we've found the factory plastic pressure pin to not be strong enough, so we've made a billet steel pressure pin against which the chain tensioner actuates to tension the crankshaft to ims drive chain. This is a return to a style of pressure pin found in very early examples of t...(choose a part on the right to read more) General FitmentBOXSTER 1997-04911 1998-05 CAYMAN 2006-08 BOXSTER 2005-08 911 2005-08
$346.63
Make a selection 98756167900GRV View/Change Diagram
$75.78
Make a selection 98756168000GRV View/Change Diagram
$82.51
Make a selection 1060813 The new revised ims retrofit tool kit is required for performing an ims retrofit. ims basic tool set. General FitmentBOXSTER 2005-08BOXSTER 1997-04 911 1998-05
$362.84
Make a selection 100270006G Only for engines updated with ims solution (oil filter adapter with oil line for ims bearing lubrication), or engines modified with spin-on filter adapter # 10 0237 009.
$21.49
Make a selection 106085 Ims solution. Solid bearing replacement with oiling system. General FitmentBOXSTER 2005-08BOXSTER 1997-04 911 1998-05
$1,897.44
Make a selection 150PB100915 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$47.52
Make a selection 1060821 Ims supplemental set. General FitmentBOXSTER 2005-08BOXSTER 1997-04 911 1998-05
$233.77
Make a selection 150PB1027 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's 911 models from 1978-89 if fitted with an 18mm original rear sway bar.
$53.46
Make a selection 150PB100918 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$47.52
Make a selection 150PB100919 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$47.52
Make a selection 150PB100922 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$47.52
Make a selection 150PB100916 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$47.52
Make a selection 93060201501 Complete distributor without an exchange. This distributor has been completely remanufactured, which includes a full inspection, disassembly, cleaning and degreasing. We then install a toothed timing belt, 3 German made top bearings, 1 German made lower bearing and a distributor pinion pin (part # 930 602 922 00). We also install new dust caps, Bosch rotors and Bosch cap. Clearances, timing and proper operation are then checked to ensure reliability.
$2,736.62
Make a selection 24135199702RS Highlights: made for up to 750*c (1,382*f) some track use and rally use. Low dust, high performance street pad with 20-25% % brake improvement. Capable of repeated heavy brake use without brake "fall-off". Very minimal disc/rotor damage characteristics. Features red "brake in' surface coating for instant safe braking after install. Superb material for European cars. Ece r 90 type approved for most cars. High performance lowest dust rating pads for prestige imports and faster street driving. Redstuff reduce dust by 60-90%. Plus the minimal dust you see is very easily removed with a simple sponge wash as it contains no steel fibre particles as in all other pads. Second they brake like an alligator right from ...(choose a part on the right to read more)
$323.14
Make a selection 372642739 Weltmeister® front camber plate set, 996/997 Boxster® & Cayman® General Fitment911 1998-05911 2005-08 BOXSTER 1997-04 BOXSTER 2005-08 CAYMAN 2006-08
$486.00
Make a selection DP31208C Ebc brakes redstuff low dust ceramic rear brake pads Porsche 911 3.4l 99-01 General Fitment911 1998-05911 2005-08 BOXSTER 1997-04 BOXSTER 2005-08 CAYMAN 2006-08 CAYMAN 2009-12
$188.90
Make a selection 90134722303R The original rubber bushing is proven to be a weak link that can fail prematurely, allowing chassis geometry to be compromised. Symptoms include suspension movement during acceleration, braking and cornering. The powerflex black series bushing is manufactured of a more dense rubber than the original. It is a 95 shore compound that is more resistant to load than standard rubber which provides better control of chassis geometry for track use. Features: designed for track use improved track handling more precise and accurate alignment constant steering geometry increased tire life better steering feedback longer service life of suspension components less nvh (noise vibration hardness) than polyurethane bushings pl...(choose a part on the right to read more)
$40.39
Make a selection 91135204108EQ If you are experiencing a pulsation and hearing grinding sounds when braking, odds are your rotors need to be replaced to restore full stopping power. This rotor is an OEM replacement (replacement for original #911 352 041 08), manufactured by zimmermann in Germany. It is internally vented and z-coated for corrosion resistance. Features: anti corrosion "z-coating" prevents rust. Simple bolt on, modifications are not necessary. Made in Germany. Sold individually. 2 necessary per car. Left or right-side fitment. Please note: rotors should always be changed in pairs. Please check the model fitment tab to ensure accurate fitment.
$179.39
Make a selection 930123002X This remanufactured turbo is a direct replacement for original part # 930 123 002 00. The remanufacturing is completed in Germany by kkk/borg warner certified technicians. This ensures reliability, superior performance and cost effectiveness. The remanufacturing process includes: complete disassembly. All parts are cleaned, inspected and measured for tolerances. Turbine wheels are replaced. Thrust bearings are replaced. All new seals are installed. Internals are reconditioned. Parts are balanced (static & dynamic) according to balancing protocol. For a complete installation we recommend adding a gasket, part # 93012319105 an intake sleeve, part # 93011015801 and be sure to have a few spare studs on hand, part #...(choose a part on the right to read more)
From $3,220.28
Make a selection 96433102100RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$725.87
Make a selection 930602015AX3ATK Send us your distributor and we will remanufacture it for you. A perfect option for those who have time and want to save on costs. The remanufacturing process includes full inspection, disassembly, cleaning and degreasing. We then install a toothed timing belt, 3 German made top bearings, 1 German made lower bearing and a distributor pinion pin (part # 930 602 922 00). Clearances, timing and proper operation are then checked to ensure reliability. Please note: each distributor is remanufactured in Germany, so the lead times can vary.
$1,552.92
Make a selection 24135191101RS Highlights: made for up to 750*c (1,382*f) fsome track use and rally use. Low dust, high performance street pad with 20-25% % brake improvement. Capable of repeated heavy brake use without brake "fall-off". Very minimal disc/rotor damage characteristics. Features red "brake in' surface coating for instant safe braking after install. Superb material for European cars. Ece r 90 type approved for most cars. High performance lowest dust rating pads for prestige imports and faster street driving. Redstuff reduce dust by 60-90%. Plus the minimal dust you see is very easily removed with a simple sponge wash as it contains no steel fibre particles as in all other pads. Second they brake like an alligator right from...(choose a part on the right to read more)
$182.95
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |