PORSCHE 924S CONTROL ARMCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: ACCESSORY (includes uncategorized and accessory items) BBI9964010002 Finally, a complete solution to properly widen the front track width of a Porsche 996 and 997 turbo. To help increase front end grip, this kit allows full negative camber adjustment without binding the axles and fitment of wider wheel/tire combinations and GT3 cup car fenders. Each kit includes lower control arms, thrust arms, axle spacers, upper mounts, and camber shims.
$3,990.60
Make a selection
$332.61
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$236.41
Make a selection FVD33150020 This kit is complete and includes the front and rear monoball cartridges with press tools. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 4. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$772.20
Make a selection FVD34101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$509.65
Make a selection FVD33150045R Replace worn-out soft rubber (65 shore hardness value) control arm bushings (camber link and caster link) with sportier rubber (75 shore hardness value) that is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing cartridge is weather sealed and is crafted in high carbon steel and 7075 t6 aircraft aluminum. Sold individually.
$74.84
Make a selection FVD34101707ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$451.44
Make a selection FVD34101802ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$509.65
Make a selection FVD34101802RAK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrange...(choose a part on the right to read more)
$652.21
Make a selection FVD34102700ATK By ordering this part number you get after previous sending in your wishbone overhauled with new race-silent blocs back. The race-silent blocs (85 shore) give you more stable driving. Should it not be repairable, we will inform you immediately.
$301.75
Make a selection
$49.90
Make a selection FVD3419991 This is a cost effective alternative to buying new control arms. Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with new bushings of the same rubber (65 shore hardness value). This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$134.24
Make a selection FVD34102800ATK By ordering this part number you get after previous sending in your wishbone overhauled with new race-silent blocs back. The race-silent blocs (85 shore) give you more stable driving. Should it not be repairable, we will inform you immediately.
$301.75
Make a selection FVD341999R Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with our FVD clubsport series. They are made from rubber with a 85 shore hardness value which is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This is the ideal upgrade for street and light track / clubsport use. This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes 85 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$134.24
Make a selection
$332.32
Make a selection 150TBF900 Replace worn-out original front control arm / wishbone bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This is located at the front of the control arm / wishbone. The correct matching poly-graphite bushing for the rear of the control arm is part # 150tbr900 sold individually. 2 necessary per car.
$52.27
Make a selection FVD721500021 Our software is capable of displaying and clearing trouble codes on most control modules. Most Porsche cars made since 1990 have multiple computers built into different parts of the car. These computers are capable of self-diagnosis. In other words, the car knows what is wrong and our tool allows you to see this information. Until now people needed to rely on car dealers to read this information from each of the car's computers. Now our software allow shops and individuals to read the fault code information out of most control modules. What does it do? · reset service reminders · reads diagnostic trouble codes · displays actual values · shows ecu information · clears diagnostic trouble codes ÂÂ...(choose a part on the right to read more)
$721.12
Make a selection FVD721500AC1 German version. Our tester is capable of displaying and clearing trouble codes on most control modules. Most Porsche cars made since 1990 have multiple computers built into different parts of the car. These computers are capable of self-diagnosis. In other words, the car knows what is wrong and our tool allows you to see this information. Until now people needed to rely on car dealers to read this information from each of the car's computers. Our tester allows shops and individuals to read the fault code information out of most control modules. What does it do? · reset service reminders · reads diagnostic trouble codes · displays actual values · shows ecu information · clears diagnostic trouble ...(choose a part on the right to read more)
$1,894.86
Make a selection 99333104503ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install the bushings. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for its return to you. We do not offer a core exchange on this part.
$283.93
Make a selection BBI9865010001 Features
$912.60
Make a selection BBI9964010003 Features
$594.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |