Vehicles
Sections
406 not categorized PORSCHE 356 C SUSPENSIONSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 944 1989-91 (includes uncategorized and accessory items) FVD33150045R Replace worn-out soft rubber (65 shore hardness value) control arm bushings (camber link and caster link) with sportier rubber (75 shore hardness value) that is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing cartridge is weather sealed and is crafted in high carbon steel and 7075 t6 aircraft aluminum. Sold individually.
$74.84
Make a selection FVD34101802RAK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrange...(choose a part on the right to read more)
$652.21
Make a selection FVD333007 These high quality, German made mounts are made specifically for rear shock absorbers that contain a 15mm i.d. Uniball spherical bearing. They are located at the base of the rear shocks, and secure the shock to the rear trailing arms. They are required with FVD exclusive suspension kits with part #'s 115 900 911 xx / xxx. For example 115900911030 they are also required for rear shocks like part # FVD33315755 sold as a set. 1 necessary per car.
$188.89
Make a selection FVD33150005 Restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm cannot compensate enough when lowering your Porsche, leaving you with as much as ½ inch of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration. Sold in pairs. 1 necessary per car.
$825.66
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$236.41
Make a selection 99333105280 The bushings are made of rubber with an 85-shore hardness value, which is more durable, provides more positive suspension location and is still quiet and comfortable for street use. Sold individually.
From $825.66
Make a selection FVD33150010 Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set. 1 kit is necessary per car. Please note: we recommend this kit for race use, as noise may resonate inside the cabin during street use. For those that are concerned about the noise, please order part # FVD3310212291
$760.32
Make a selection BK7033 Re-issue of autobooks manual covering engine, fuel & cooling systems, ignition, heating, exhaust emissions, clutch, transmission, rear axle, suspension, steering gear, brakes, electronics, and bodywork. This is a manual that will help keep 912 on the road. A must for any 912 owner. General FitmentACCESSORY
$34.56
Make a selection BES98215000S2 The open architecture of this muffler allows for a deeper four-cylinder turbo tone, with plenty of whistling on tap. Coming off throttle from higher rpms exudes a chorus of snarling, gurgling and crackling letting everyone know that this car is not your average 982. + 15 hp & + 12 tq gain. - 2 x 3.5 (90 mm) round tips. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - lower deeper tones than the factory exhaust with far more whistling and gurgling / crackling off throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - no drone in the cabin. - "aero quip" style motorsport muffler connections t...(choose a part on the right to read more)
$3,041.28
Make a selection FVD3310212291 Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. It offers rs style handling characteristics, superior durability and is still forgiving enough for street use. - better handling. - makes precision adjustments of the suspension easier. - does not produce road noise. - shore hardness value of 85. - direct OEM replacement. - more forgiving for street use. -includes press tools and grease for easier assembly. Sold as a set. 1 kit is necessary per car. Please note: this fits the 964 c2 / c4 and rs america. Not keen on installing or having the bushings installed at a shop? Please check out our part # FVD33399603b8 and FVD33399603b8, we wil...(choose a part on the right to read more)
$974.16
Make a selection BES981C5000SKGT Gt4 clubsport ++ with the valves open. Completely civilized at low rpms and while cruising. + 11 hp & + 10 tq gain. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - 2 3/4 tubing. - 2 x 3.5 (90 mm) round tips. - intoxicating growl at idle, partial throttle and wide open throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - minimal resonance / drone in the cabin. - "aero quip" style motorsport muffler connections to ensure a leak free exhaust. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. Please note: gaskets a...(choose a part on the right to read more)
$5,791.50
Make a selection BBI9964010001 Features
$567.00
Make a selection 99634304349 Serie production spring seat must be used! Bilstein b4 OEM (original equipment manufacturer) replacement shock absorber for your Porsche with standard suspension. The b4 damper from bilstein is the perfect replacement for your Porsche. Facts: - constant damping power under any load - high power reserves for maximum safety - ride like it's the first time, every time - OEM quality - bilstein gas pressure technology
From $465.56
Make a selection FVD33150030 This kit is complete and includes a total of 8, 4 smaller and 4 larger for the rear control arms. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 8. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$806.65
Make a selection BES98115001SK This is our jekyll and hyde version ! The perfect compromise for you and your loved ones. Rich, deep race car tones with the valves open and soft subtle, completely stock sounds with them closed. Top of the line or range depending on the english, and is the best choice for a daily driver. + 11 hp & + 10 tq gain. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - 2 1/2 tubing (63.5 mm). - 2 x 3.5 (90 mm) round tips. - intoxicating growl at idle, partial throttle and wide open throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - minimal resonance / drone in the cabin (200 rpms worth) compared t...(choose a part on the right to read more)
$5,613.30
Make a selection 99633305153 Bilstein b4 OEM (original equipment manufacturer) replacement shock absorber for your Porsche with standard suspension. The b4 damper from bilstein is the perfect replacement for your Porsche. Facts: - constant damping power under any load - high power reserves for maximum safety - ride like it's the first time, every time - OEM quality - bilstein gas pressure technology
$497.75
Make a selection FVD33150020 This kit is complete and includes the front and rear monoball cartridges with press tools. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 4. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$772.20
Make a selection 99634304347 Serie production spring seat must be used! Bilstein b4 OEM (original equipment manufacturer) replacement shock absorber for your Porsche with standard suspension. The b4 damper from bilstein is the perfect replacement for your Porsche. Facts: - constant damping power under any load - high power reserves for maximum safety - ride like it's the first time, every time - OEM quality - bilstein gas pressure technology
From $465.56
Make a selection FVD721T221 Camber adjuster needed to adjust toe - in of the rear suspension.
$16.63
Make a selection 96434307001SP Replace your old drop links to reduce body roll and rejuvenate your cars handling in the corners. Sport-version with 85 shore 964 c2 only with m030 factory sport suspension sold individually. 1 necessary per car.
$257.80
Make a selection 98633305130 Bilstein b4 OEM (original equipment manufacturer) replacement shock absorber for your Porsche with m030-sportsuspension. The b4 damper from bilstein is the perfect replacement for your Porsche. Facts: - constant damping power under any load - high power reserves for maximum safety - ride like it's the first time, every time - OEM quality - bilstein gas pressure technology
From $396.90
Make a selection 911FDLNK Upgrade your stock front swaybar with this simple bolt in replacement for the factory drop links.
$221.40
Make a selection 96434306901SP Replace your old drop links to reduce body roll and rejuvenate your cars handling in the corners. Sport-version with 85 shore 964 c2 only with m030 factory sport suspension sold individually. 1 necessary per car.
$257.80
Make a selection 477412031B Sach/boge suspension components have been standard equipment on Porsche for years. Buy with the knowledge that the factory uses sachs/boge parts and stands behind their quality and precision that they bring to everything the manufacture. Sachs/boge shocks and struts provide a taut, sporty ride while remaining a comfortable street ride.
$111.24
Make a selection 150TBF900 Replace worn-out original front control arm / wishbone bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This is located at the front of the control arm / wishbone. The correct matching poly-graphite bushing for the rear of the control arm is part # 150tbr900 sold individually. 2 necessary per car.
$52.27
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |