Vehicles
Sections
397 not categorized PORSCHE 986 ENDCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 944 1989-91 (includes uncategorized and accessory items) 911606105JXATK The cis injection / k-jetronic warm up regulator is a critical component that performs the following functions: lowers pressure when engine is cold. Absorbs / distributes engine heat. Allows for an additional rich mixture under full load to prevent engine damage. Altitude correction. Send us your original part and we will have it remanufactured for you. We do not offer a core exchange on this part. Each part is remanufactured in Germany, so the lead times can vary. Sold individually. 1 necessary per car. Please note: this part number encompasses: Bosch part 0 438 140 045 for 911 SC models from 1977-80 and Bosch part 0 438 140 089 for 911 SC models from 1980-83
$781.94
Make a selection 91134732204EQ The symptoms of a worn tie rod end include, clunking, rattling and squeaking when turning, poor alignment and premature tire wear. Have the rod ends inspected when servicing your suspension and proactively change them when noticing any of the symptoms. Quality European aftermarket replacement designed to perform like the original. Sold individually. Left or right-side fitment. 2 necessary per car.
$68.15
Make a selection 914503031F Excellent repair panel for the front of your rusted or crashed 914 fender
$43.96
Make a selection 93150302102R02 Kotflugel hat zur windschutzscheibe hin ein abgebogenes eck.
$1,518.55
Make a selection 914503032G Excellent panel to repair the front fender front dog leg area under the side marker
$78.75
Make a selection 92833226701 This is a high-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per axle.
From $6.93
Make a selection 94460617001 For all 944 and 944s2 models this is the device that signals the control unit to cause the coil to spark. when this device fails your car is dead in the water, there is fuel pressure but no spark.
$151.91
Make a selection 96433102100RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$705.71
Make a selection 93020705304 Pmo parts is proud to introduce a euro style oil cooler to replace “trombone” style coolers used in most g-model cars.
From $459.00
Make a selection 96434732202EQ The symptoms of a worn tie rod end include, clunking, rattling and squeaking when turning, poor alignment and premature tire wear. Have the rod ends inspected when servicing your suspension and proactively change them when noticing any of the symptoms. Sold individually. Left or right side fitment. 2 necessary per car.
$51.98
Make a selection 964347009BXATK This steering rack is a remanufactured part with a core, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and resell-able, the core deposit will be refunded. The remanufacturing process includes full inspection and testing for structural integrity. We then disassemble and bead blast to remove corrosion. Internals are micro-finished to OEM specifications. Sealing surfaces are carefully checked and restored prior to installing new premium seals and o-rings. Each unit is then carefully tested for full functional...(choose a part on the right to read more)
$1,715.18
Make a selection 99911342641EQ High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
$32.34
Make a selection FVD201911RSR100 Whether you are restoring a tribute car or endurance racing your 911, this tank will fit the bill. It is made in Germany from pvc plastic and includes high grade threaded brass inserts. It is build by fia specs and can be adapted to work in all 911's from 67-89. It holds a capacity of 26.4 gallons or 100 liters.
$3,218.99
Make a selection BES99715040S2 Quiet version with catalytic bypass and 4x80mm end tips these versions of FVD sport exhaust system is specifically made for increased performance vehicles. Designed for tolerable, pleasant and sonorous sound (especially for the turbo cabriolet). The elimination of the catalysts reduced drastically the back pressure and increases the performance and throttle response to the max! - stainless steel exhaust system - catalytic bypass - 4x80mm end tips - 2 3/4 tubing (70mm) straight through design for maximum power - weighs 39 lbs. (18,1 kg) - made in Germany - dme programming necessary (catalytic adaption) - stock tips will fit. Tech tip: order also repair / gasket set FVD mk9 970 02
$3,074.61
Make a selection
$1,044.75
Make a selection FVD123013ATK K-16/24 turbo (up to 555 hp) power is focused on low and mid range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD brombachers 993 k-16/24 remanufactured turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The remanufacturing process starts with re-profiling the OEM turbochar...(choose a part on the right to read more)
$3,125.43
Make a selection BT4000 Never worry about a dead battery while your car is in storage or you’re away as long as you have the battery tender. This handy device will monitor your battery’s voltage constantly. Don’t worry about over charging, the tender automatically goes into a floating mode once your battery is fully charged. This great item will increase the life of your battery. General FitmentACCESSORY
$73.45
Make a selection FVD50399701MM Louvers slats they are such a unique feature, so important. By opening the front fenders, and allowing the hot air from the brakes to get ventilated out of the wheel arch! To mount on top or bottom of the exist front fender. For all Porsche 997 Carrera | s | 4s | GTS | GT3 | targa | turbo s | GT2 | GT2 rs | sport classic
$672.21
Make a selection FVD201911RSR110 Whether you are restoring a tribute car or endurance racing your 911, this tank will fit the bill. It is made in Germany from pvc plastic and includes high grade threaded brass inserts. It is build by fia specs and can be adapted to work in all 911's from 67-89. It holds a capacity of 29 gallons or 110 liters.
$3,218.99
Make a selection FVD123047ATK FVD Brombacher997.2 tt "700 series" upgraded turbos facts: - modified compressor housing for the 3.8 l displacement - modified & lightened billet compressor wheel with 12 blades - 49.55 mm inducer - 68 mm exducer - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already running FVD software we start by re-profiling the OEM vtg turbocharger compressor housing and modifying the compressor backing plate. This is done to replace the factory compressor wheel with a larger 12 blade, modified compressor wheel. The larger wheel is also lightened allows the turbo to flow a larger volume of air (more power), and aids i...(choose a part on the right to read more)
$2,766.23
Make a selection FVD503997GT3CUP For both front fender (4 pieces), widening per fender approx. 2cm. Requires the removal of the side marker.
$1,249.79
Make a selection FVD50399101MM The moshammer front fender set blends just the right amount of motorsport pedigree with functionality. This aggressive design is captivating on any 991 model and offers a level of exclusivity not found with competitors body kits. The integrated fender vents lower the thermal load on the brakes by allowing the heat to be quickly ventilated up and out of the wheel arch. This composite fender set has been meticulously designed to bolt up to the factory locations for perfect panel fitment, alignment and consistent gaps. A perfect addition for a leased vehicle or for those looking to return the car to its original appearance in the future. These fenders complement the entire moshammer stormforce (991.1) / stormforce...(choose a part on the right to read more)
$3,812.66
Make a selection 914503032F Excellent repair panel for this area of the front 914 fender
$43.96
Make a selection FVDMK997004 Installation made easy! Replace worn hardware and gaskets with one of our prepackaged installation kits.
$281.89
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |