Vehicles
Sections
71 not categorized PORSCHE CAYMAN S CIS BOXCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 944 1989-91 (includes uncategorized and accessory items) FVD505981SCH Motorsport quality grp (glass-reinforced plastic) front bumper, specifically produced for the early 911 style headlights up to 2001. This will fit all 986 Boxster models however. - produced by a German motorsport manufacturer. - provisions for turn signals are included. - lightweight - made of high strength, grp (glass-reinforced plastic) - includes a sheet of black race mesh for the radiator inlets. Please note: this is a motorsport part that takes time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world. All grp products must properly be fitted and completely prepared prior to paint. They require pre-fitment, filling, sanding, primer and paint...(choose a part on the right to read more)
$1,449.93
Make a selection FVD98661810MG Genuine: engine - 6 cylinder boxer capacity - 2480ccm compression ratio - 11,0:1 max. Power - 150kw (204hp) @ 6000rpm max. Torque - 245nm (181lbf ft) @ 4500rpm max. Speed - 240km/h max. Rpm - 6700rpm acceleration 0-100km/h - 6.9s tuning: max. Power - 158kw (215hp) @ 6000rpm max. Torque - 260nm (192lbf ft) @ 4500rpm max. Speed - 247km/h max. Rpm - 6900rpm acceleration 0-100km/h - 6.7s very important note: our tool can only flash ecu's with the Bosch # 0 261 204 605. If your ecu does not have this Bosch # then the ecu must be sent to us to be flashed in house. Please check the sticker on the outside of your ecu to determine which Bosch # you have. You can check by opening the rear trunk and pulling the carpet li...(choose a part on the right to read more)
$1,033.73
Make a selection FVD351997TTCS1 This kit convert's the 997 turbo pccb rotors to steel rotors with yellow pagid pads.( only 5-hole, not central lock ) this system is complete with everything that you need to install. Do not ruin your expensive ceramic brake discs on the track. Get ready for racing with the original and much cheaper Porsche motorsport steel brake discs! What's in the box: 4 x 2-piece brake discs (380 x 34 mm - front / 350 x 28 mm - rear) 4 x wear sensors 2 x set ( front and rear ) brake pad set (pagid yellow - rs29 ) 8 x screws for brake caliper 8 x damping plates technical tip: also order stainless steel brake lines (FVD b96 355 97) and racebrake fluid (012 145 ca).
$6,165.39
Make a selection FVD351997TTCS This kit convert's the 997 turbo pccb rotors to steel rotors with yellow pagid pads.( only 5-hole, not central lock ) this system is complete with everything that you need to install. Do not ruin your expensive ceramic brake discs on the track. Get ready for racing with the original and much cheaper Porsche motorsport steel brake discs! What's in the box: 4 x 2-piece brake discs (380 x 34 mm - front / 350 x 28 mm - rear) 4 x wear sensors 2 x set ( front and rear ) brake pad set (pagid yellow - rs29 ) 8 x screws for brake caliper 8 x damping plates technical tip: also order stainless steel brake lines (FVD b96 355 97) and racebrake fluid (012 145 ca).
$6,662.04
Make a selection FVD99661831MG Genuine: engine - 6 cylinder boxer capacity - 3600ccm compression ratio - 11,7:1 max. Power - 265kw (360hp) @ 7200rpm max. Torque - 370nm (273lbf ft) @ 5000rpm max. Speed - 302km/h max. Rpm - 7600rpm acceleration 0-100km/h - 4.8s tuning: max. Power - 276kw (375hp) @ 7000rpm max. Torque - 390nm (288lbf ft) @ 5000rpm max. Speed - 310km/h max. Rpm - 7900rpm acceleration 0-100km/h - 4.6s for 27 + years, FVD-Brombacherhas been setting the standard for Porsche engine building and tuning in Germany. Our deep understanding of the flat 6 Porsche engine naturally led to our engine management software. Over the years we have perfected the art of software tuning, making substantial gains in horsepower and torque, while re...(choose a part on the right to read more)
$1,264.73
Make a selection MAP09028016 The Porsche flat six boxer engine and the cars it powers are legendary. with this kit you can assemble a model of a 1966 2.0 litre flat six engine in around three hours. Discover the fascinating world of automotive engineering with the whole family
From $204.75
Make a selection FVD1169011 Our FVD exclusive line of clutch kits is culmination of Porsche genuine parts, zf sachs race engineering gmbh parts and motorsports parts that have been developed to work together without compromise. They offer a silky-smooth release, superb drivability, can handle more torque (354 ft/lbs. / 480 nm max.) than comparable stage type recommendations. We specifically chose a clutch disc with torsion springs that function as a vibration damper between engine and gearbox, which provides an effortless release in 1st gear. This kit is suited for daily use and offers a superior driving experience. This kit also uses a lightweight zf sachs race engineering gmbh aluminum pressure plate. Kit includes: 1 qty. Oraganic clutc...(choose a part on the right to read more)
$1,642.79
Make a selection I09BLACK Now you can repair the broken glove box hinges with high quality anodized aluminum straps! Porsche made the mistake of making the glove box door and hinge straps all one piece. Expensive to replace (over $350)! Now you no longer have to suffer the flapping lid by replacing the broken hinges with this handy kit. Installation is a snap and the are guaranteed for life! Glove box hinge repair kit for all late 944s and 968s and fix those flimsy plastic straps forever with these strong anodized aluminum ones! General Fitment944 1985-88944 1989-91 968 1992-95
$56.60
Make a selection FVD99610061A Kit includes: software genius flash tool, sport air filter genuine: engine - 6 cylinder boxer twin-turbo capacity - 3600ccm compression ratio - 9,4:1 max. Power - 331kw (450hp) @ 5700rpm max. Torque - 620nm (457lbf ft) @ 3500-4500rpm max. Speed - 318km/h max. Rpm - 6750rpm acceleration 0-100km/h - 4.0s tuning: max. Power - 375kw (510hp) @ 5000rpm max. Torque - 745nm (550lbf ft) @ 4500rpm max. Speed - 328km/h max. Rpm - 7000rpm acceleration 0-100km/h - 3.8s for 27 + years, FVD-Brombacherhas been setting the standard for Porsche engine building and tuning in Germany. Our deep understanding of the flat 6 Porsche engine naturally led to our engine management software. Over the years we have perfected the art of so...(choose a part on the right to read more)
$2,170.59
Make a selection SESDP924 Safety devices 6 point competition bolt-in roll cage kit offered by stable energies includes: bolt on door bars, harness bar and diagonal. Optionally, the diagonal is offered in a non-removable version. Please refer to the part number to specify correctly when ordering. The bolt on harness bar is offset towards the rear to allow full movement of the front seats. This harness bar also incorporates shoulder harness guides which locate the shoulder harnesses on the harness bar. For the club racers, a seat back brace can be attached to the harness bar as well. General Fitment924 1976-79924 1980-85 924 1986-88 944 1989-91 944 1985-88 944 1982-85
$1,429.31
Make a selection RES98720000SS Having to weld up cracks regularly on your current aftermarket racing exhaust? If you are looking for a racing exhaust that can handle abuse at the track, look no further. This exhaust system is manufactured by m&m exhaust, gmbh in Germany. They manufacture a multitude of Porsche motorsport and racing exhausts. Each system is designed for reliability and performance gains throughout the entire rev range. Not to mention, you directly benefit from everything m&m learns at the track, so their systems designs are never static. Also, each system is tested comprehensively for flow characteristics / rate, thermal stress, cracking, and longevity. Features: + 20 hp & + 19 tq catalytic bypass pipes weighs 55 lbs. (23 kg)...(choose a part on the right to read more)
$5,336.10
Make a selection SESDP944 Safety devices 6 point competition bolt-in roll cage kit offered by stable energies includes: bolt on door bars, harness bar and diagonal. Optionally, the diagonal is offered in a non-removable version. Please refer to the part number to specify correctly when ordering. The bolt on harness bar is offset towards the rear to allow full movement of the front seats. This harness bar also incorporates shoulder harness guides which locate the shoulder harnesses on the harness bar. For the club racers, a seat back brace can be attached to the harness bar as well. General Fitment924 1986-88944 1982-85 944 1985-88 944 1989-91 968 1992-95
$2,095.05
Make a selection BS23473 Bbs continues to transfer race car technology and race-bred performance to road wheels designed for the latest high-performance luxury automobiles. As always, bbs pushes itself to set new standards, aiming to radically reduce wheel weight while ensuring absolute concentricity, perfect balance, and the stability its reputation has been built upon. The lm wheel features a painted center, diamond cut rim, and a protective top coat for a beautiful finish. General Fitment924 1980-85924 1986-88 944 1982-85 944 1985-88 944 1989-91 968 1992-95 BOXSTER 1997-04 BOXSTER 2005-08 911 1974-77 911 1978-83 911 1984-86 911 1987-89 911 1989-94 911 GT3 2007-11 911 2005-08 911 GT3 2003-05 911 1998-05 911 1994-98 CAYMAN 2006-08
$1,172.47
Make a selection FVD111LAMVER Having problems with your check engine light? Want to run cat bypass pipes or a free flowing sports catalyst set up on your vehicle without having to reprogram the dme (ecu)? This adapter offsets the oxygen sensor about 1.5 inch from the gas stream. This achieves, in most cases, a sufficient measurement for the air/co ratio and increases the tolerance range between the pre and post cat oxygen sensors. In addition, the sensitivity of the oxygen sensor is also reduced allowing you to run a nearly any exhaust or catalytic set up, including bypass pipes, without the need to reprogram your ecu! Use only for the 2nd oxygen sensor (after catalytic)! General FitmentBOXSTER 1997-04911 GT3 2007-11 911 2005-08 911 GT3 2003-05 911 TURBO/GT2 2001-05 911 1998-05 911 1989-94 911 1987-89 911 1984-86 911 1978-83 CAYENNE 2007-10 CAYENNE 2003-06 CAYMAN 2006-08 BOXSTER 2005-08 968 1992-95 944 1982-85 944 1985-88 944 1989-91 928 1992-95 928 1987-91 928 1983-86 924 1986-88 924 1980-85 911 1994-98
$45.05
Make a selection GR246371 Pentosin longtime antifreeze is specifically adapted for use in alloy engines. It offers excellent advantages over other similar products: prevents lime formation, does not foam, protects against corrosion and cavitation, nitrite, amine and phosphate free, manufactured to meet the exacting standards of din, astm and dbl and is formulated for all year use. Longtime anti freeze in recommended for Porsche 924, 944 and 968 models. General Fitment924 1976-79924 1980-85 924 1986-88 944 1989-91 944 1985-88 944 1982-85 928 1992-95 928 1987-91 928 1983-86 928 1978-82 968 1992-95 BOXSTER 1997-04 BOXSTER 2005-08 CAYMAN 2006-08 CAYENNE 2003-06 CAYENNE 2007-10 911 GT3 2007-11 911 2005-08 911 GT3 2003-05 911 TURBO/GT2 2001-05 911 1998-05
$15.25
Make a selection GR2041 Fully synthetic 5w-40 motor oil is the choice for today's high tech engines. It has been formulated according to the German car manufacturers' latest specifications to provide unsurpassed protection and performance. Improves fuel mileage, helps in cold starting, and lowers oil consumption. General Fitment968 1992-95944 1989-91 944 1985-88 944 1982-85 928 1992-95 928 1987-91 928 1983-86 928 1978-82 924 1986-88 924 1980-85 924 1976-79 BOXSTER 1997-04 BOXSTER 2005-08 CAYMAN 2006-08 CAYENNE 2003-06 CAYENNE 2007-10 911 1998-05 911 2005-08
$48.44
Make a selection 99720198000 Inspired by the fuel filler caps on historic racing cars, this elegant accessory features an engraved Porsche® logo and can be safety tethered to the car. View/Change Diagram
$213.40
Make a selection SA03 These brackets have been specially designed to allow you to install both, factory seat belts and aftermarket harnesses at the same time. Intended for the use of quick disconnect lap belts on both sides of the seat. This is a perfect set up for your street/track car. All brackets are designed to attach to the factory seat belt mounting locations so no drilling is required. General Fitment911 1965-69356 1960-65 912 1965-69 911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89 911 1989-94 911 1994-98 911 1998-05 911 TURBO/GT2 2001-05 911 GT3 2003-05 911 2005-08 911 GT3 2007-11 944 1989-91 944 1985-88 944 1982-85 928 1992-95 928 1987-91 928 1983-86 928 1978-82 924 1986-88 924 1980-85 924 1976-79 914 1970-76 CAYMAN 2006-08 BOXSTER 2005-08 BOXSTER 1997-04 968 1992-95
$56.60
Make a selection WE35406 Bbs continues to transfer race car technology and race-bred performance to road wheels designed for the latest high-performance luxury automobiles. As always, bbs pushes itself to set new standards, aiming to radically reduce wheel weight while ensuring absolute concentricity, perfect balance, and the stability its reputation has been built upon. The lm wheel features a painted center, diamond cut rim, and a protective top coat for a beautiful finish. General Fitment924 1980-85924 1986-88 944 1982-85 944 1985-88 944 1989-91 968 1992-95 BOXSTER 1997-04 BOXSTER 2005-08 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89 911 1989-94 911 1994-98 911 1998-05 911 GT3 2003-05 911 2005-08 911 GT3 2007-11 CAYMAN 2006-08
$1,289.56
Make a selection HR5511 If you have room in your fender well to spacer your wheels out, here is an easy way to improve your Porsche’s handling. Made of aluminum/magnesium alloy these hard anodized spacers are hub-centric and up to 70% lighter than typical steel wheel spacers. Made in Germany. Spacers come with wheel bolts, studs and nuts. General Fitment356 1960-65912 1965-69 911 1989-94 911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1965-69 911 1994-98 914 1970-76 924 1986-88 928 1978-82 928 1983-86 928 1987-91 928 1992-95 944 1982-85 944 1985-88 944 1989-91 968 1992-95 BOXSTER 1997-04 BOXSTER 2005-08 CAYMAN 2006-08 CAYENNE 2003-06 CAYENNE 2007-10 911 1998-05 911 TURBO/GT2 2001-05 911 GT3 2003-05 911 2005-08 911 GT3 2007-11
$289.22
Make a selection WE35408 Bbs continues to transfer race car technology and race-bred performance to road wheels designed for the latest high-performance luxury automobiles. As always, bbs pushes itself to set new standards, aiming to radically reduce wheel weight while ensuring absolute concentricity, perfect balance, and the stability its reputation has been built upon. The lm wheel features a painted center, diamond cut rim, and a protective top coat for a beautiful finish. General Fitment924 1980-85924 1986-88 944 1982-85 944 1985-88 944 1989-91 968 1992-95 BOXSTER 1997-04 BOXSTER 2005-08 911 1974-77 911 1978-83 911 1984-86 911 1987-89 911 1994-98 911 1998-05 911 GT3 2003-05 911 2005-08 911 GT3 2007-11 CAYMAN 2006-08
$1,760.91
Make a selection WE35407 Bbs continues to transfer race car technology and race-bred performance to road wheels designed for the latest high-performance luxury automobiles. As always, bbs pushes itself to set new standards, aiming to radically reduce wheel weight while ensuring absolute concentricity, perfect balance, and the stability its reputation has been built upon. The lm wheel features a painted center, diamond cut rim, and a protective top coat for a beautiful finish. General Fitment924 1980-85924 1986-88 944 1982-85 944 1985-88 944 1989-91 968 1992-95 BOXSTER 1997-04 BOXSTER 2005-08 911 1974-77 911 1978-83 911 1984-86 911 1987-89 911 1989-94 911 GT3 2007-11 911 2005-08 911 GT3 2003-05 911 1998-05 911 1994-98 CAYMAN 2006-08
$1,689.77
Make a selection MT1000 These high-quality mats add a touch of elegance to your car's interior. Each set of mats are custom made to your specifications to perfect fit your favorite auto. Our mats are made of the most durable heavy duty plush carpet with professional stitching and rubber backing to prevent slippage. These tough mats come in a variety of colors. Please be sure to indicate color when ordering. General FitmentALL
$149.50
Make a selection 47075004 Bmc sport air filters were originally developed in association with the ferrari f1 team. Bmc started producing their filters in 1973 and is one of the most recognized brands in the European automotive industry and is a member of the vdat German tuning association. Oem filters only require a total particle filtration efficiency up to a minimum size of 10 microns. Oem air filters function primarily to protect the engine, so they are cost effectively produced in paper. Paper filters have high resistance to airflow that reduces the inlet pressure and consequently engine performance. Bmc filtration systems yield more engine performance, both in terms of power and torque without compromising reliability. A bmc sport ...(choose a part on the right to read more)
$236.78
Make a selection 47041616 Bmc sport air filters were originally developed in association with the ferrari f1 team. Bmc started producing their filters in 1973 and is one of the most recognized brands in the European automotive industry, they are also a member of the vdat German tuning association. Oem filters only require a total particle filtration efficiency up to a minimum size of 10 microns. Oem air filters function primarily to protect the engine, so they are cost effectively produced in paper. Paper filters have high resistance to airflow that reduces the inlet pressure and consequently engine performance. Bmc filtration systems yield more engine performance, both in terms of power and torque without compromising reliability. A bm...(choose a part on the right to read more)
$123.59
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |