PORSCHE 944 BYPASSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 944 1982-85 (includes uncategorized and accessory items) FVD98010002 Kit includes: 2 x sport motronic dme (ecu) exchange 2 x sport airfilter 1 x sport exhaust system genuine: engine - v10 cylinder capacity - 5733ccm compression ratio - 12,0:1 max. Power - 450kw (612hp) @ 8000rpm max. Torque - 590nm @ 5750rpm max. Speed - 330km/h max. Rpm - 8400rpm acceleration 0-100km/h - 3.9s tuning: max. Power - 496kw (675hp) @ 8000rpm max. Torque - 670nm (495 lbf ft) @ 6000rpm max. Speed - 345km/h max. Rpm - 8600rpm acceleration 0-100km/h - 3.7s FVD dme / ecu programming philosophy: for 27 + years, FVD-Brombacherhas been setting the standard for Porsche engine building and tuning in Germany. Our deep understanding of the flat 6 Porsche engine naturally led to our engine management software. ...(choose a part on the right to read more)
$18,394.67
Make a selection FVD95761890MG Factory: engine - v8 twin-turbo capacity - 4806ccm compression ratio - 10,5:1 max. Power - 368kw (500hp) @ 6000rpm max. Torque - 700nm (516 lbf ft) @ 2250-4500rpm max. Speed - 275km/h max. Rpm - 6500rpm acceleration 0-100km/h - 5.1s tuning:* max. Power - 397kw (540hp) @ 6000rpm max. Torque - 780nm (575 lbf ft) @ 3500rpm max. Speed - 280km/h max. Rpm - 6700rpm acceleration 0-100km/h - 5.0s * only with sport exhaust system and sport air filter for 27 + years, FVD-Brombacherhas been setting the standard for Porsche engine building and tuning in Germany. Our deep understanding of the flat 6 Porsche engine naturally led to our engine management software. Over the years we have perfected the art of software tuning, ...(choose a part on the right to read more)
$1,182.06
Make a selection RES96400100S1 More low and mid-range torque than our race system with cat bypass. Larger primaries, larger collector, largest diameter tubing on the market. Made for mid-range and top end performance with the added beauty of dual exhaust tips! + 25 hp & + 23 torque - 100 cell hjs tri-metallic race catalytics. -2 1/2 tubing (63.5mm) for max. Power across the rpm range.* -weighs 49 lbs. (22 kg). -German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - aeroquip cone style catalytic connection design to prevent exhaust leaks. -includes aeroquip quick release clamps. -made in Germany by m&m exhaust, gmbh. -dual round 3 exhaust tips -intoxicating flat 6 growl at idle, partial throttle and wide open throttle. P...(choose a part on the right to read more)
$8,394.41
Make a selection FVD99610061A Kit includes: software genius flash tool, sport air filter genuine: engine - 6 cylinder boxer twin-turbo capacity - 3600ccm compression ratio - 9,4:1 max. Power - 331kw (450hp) @ 5700rpm max. Torque - 620nm (457lbf ft) @ 3500-4500rpm max. Speed - 318km/h max. Rpm - 6750rpm acceleration 0-100km/h - 4.0s tuning: max. Power - 375kw (510hp) @ 5000rpm max. Torque - 745nm (550lbf ft) @ 4500rpm max. Speed - 328km/h max. Rpm - 7000rpm acceleration 0-100km/h - 3.8s for 27 + years, FVD-Brombacherhas been setting the standard for Porsche engine building and tuning in Germany. Our deep understanding of the flat 6 Porsche engine naturally led to our engine management software. Over the years we have perfected the art of so...(choose a part on the right to read more)
$2,232.61
Make a selection RES99111060SL Our entire "brombacher" line of exhausts is manufactured by m&m exhaust, gmbh in Germany. They manufacture a multitude of Porsche motorsport and racing exhausts. Each system is tested comprehensively for flow characteristics, thermal stress, cracking, and longevity. If you are looking for an exhaust product that can handle abuse at the track, look no further. Features: - made of t 316 motorsport grade stainless steel for improved durability over t 304. - fits 991.2 GT3 & GT3 rs models. - connects seamlessly to factory side mufflers or side muffler bypass. - does not include o2 sensor bungs like competitors' products, so laminar flow is retained. - reuses factory exhaust rings and clamps. - made in Germany by...(choose a part on the right to read more)
$4,239.97
Make a selection FVD95761891MG Genuine: engine - v8 capacity - 4806 ccm compression ratio - 12,5:1 max. Power - 298kw (405hp) @ 6500rpm max. Torque - 500nm @ 3500rpm max. Speed - 253km/h max. Rpm - 7000rpm acceleration 0-100km/h - 6,1s tuning: max. Power - 312kw (425hp) @ 6000rpm max. Torque - 520nm @ 4500rpm max. Speed - 265km/h max. Rpm - 7200rpm acceleration 0-100km/h - 5,7s for 27 + years, FVD-Brombacherhas been setting the standard for Porsche engine building and tuning in Germany. Our deep understanding of the flat 6 Porsche engine naturally led to our engine management software. Over the years we have perfected the art of software tuning, making substantial gains in horsepower and torque, while retaining drivability and most importan...(choose a part on the right to read more)
$1,182.06
Make a selection BES95B05040SK + 15 hp & + 18 tq gain. - 2.5 tubing (63.5mm). - 4 x 4 (101mm) round tips. - 8.5 lb. Weight savings over OEM mufflers. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - electronic valve controller must be removed from the OEM unit and added to our muffler. - made in Germany. Please note: this muffler is a direct replacement the macan turbo (95b) model which comes with a single electronic exhaust valve on the passenger side. This is the very 1st aftermarket muffler for the macan 95b turbo that includes a valve like the factory system. This allows our system ...(choose a part on the right to read more)
$4,907.63
Make a selection FSPOR992SC Purchase disclaimer: fabspeed motorsport does not condone the use of emission defeat devices for any vehicles used on public streets or roadways. Fabspeed motorsport will not tamper, remove, disable, or bypass emissions equipment on a motor vehicle in accordance with 40 cfr section 86.1854.12(a)(3), clean air act 40 cfr 1068.101(b). This includes software, known as tunes, that reprogram a motor vehicles electronic control module to alter engine performance and enable the removal of filters, catalysts, and other critical emissions controls.
$3,991.63
Make a selection BES99104060S + 11 hp & + 10 tq gain. - 2 3/4 tubing (70mm). - weighs 35.2 lbs (16 kgs) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - does not interfere with emissions and will not trigger the check engine light. - includes block off plates & caps to use with either the OEM center muffler or an aftermarket center muffler bypass (with 2 inlets). - replaces the OEM valved side mufflers. Connects to OEM header and catalytic flange and connects to OEM center muffler or bypass. - can be used with bes99107060s1 for an even more aggressive growl. * please note - you will no longer have use of your valves ! Our 991 GT3 side muffler replacements are vastly different than the baffle plated mufflers stu...(choose a part on the right to read more)
$1,931.69
Make a selection FVD98010001 Kit includes: 2 x sport motronic dme (ecu) exchange 2 x sport airfilter genuine: engine - v10 cylinder capacity - 5733ccm compression ratio - 12,0:1 max. Power - 450kw (612hp) @ 8000rpm max. Torque - 590nm @ 5750rpm max. Speed - 330km/h max. Rpm - 8400rpm acceleration 0-100km/h - 3.9s tuning: max. Power - 478kw (650hp) @ 8000rpm max. Torque - 640nm @ 6000rpm max. Speed - 340km/h max. Rpm - 8600rpm acceleration 0-100km/h - 3.8s our Carrera GT ecu programming offers you not only more power and torque but phenomenal sound! Within the cgt end muffler is a flap-type mechanism fitted which is controlled by vacuum units. These vacuum units are also controlled by the ecu. Our programming modifies the control of these f...(choose a part on the right to read more)
$8,201.91
Make a selection FVD111LAMADP 90 degree adapter for hard to reach places. General FitmentALL
$70.09
Make a selection RES99700062S
From $8,193.88
Make a selection RES99700061S
From $8,194.63
Make a selection RES99700060S Race exhaust system 997 GT3 cup (2010+ 3.8 l), stainless steel. - header diameter 50mm - tube diameter 70mm after the headers - recommended for engines 450hp+ all motorsport and racing parts are special order items. Special order items must be paid for in advance. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis and do not carry any warranty. No exceptions.
From $5,920.99
Make a selection RES99710080S Race system grand am spec. 997 3.6l & 3.8l facts: - headers - 3 x 45mm (1.77") diameter tubing into a 1 x 70mm (2.75") collector (reduces thermal stress) - muffler - interchangeable cat bypass tube w/ 4 tube style mufflers, tubing 70mm (2.75") - weighs 36 lbs. (16,4 kg) - developed for excellent mid range torque needed out of corners - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability - made in Germany - intoxicating growl at idle, partial throttle and wide open throttle - 997 3.6l & 3.8l - grand-am regulation 106db - approved for use in the grand-am continental series - no dme programming necessary includes: 4 x conical springs 2 x adjustable exhaust tips w/ clamps 1 x muffler bracke...(choose a part on the right to read more)
From $5,722.60
Make a selection RES99620060S Race exhaust system 996 GT3, stainless steel, cat bypass with tips facts: - + 25 crank hp & + 19 crank torque - catalytic bypass - includes quick release clamps - made in Germany - dme programming necessary. All motorsport and racing parts are special order items. Special order items must be paid for in advance. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis and do not carry any warranty. No exceptions.
From $4,579.74
Make a selection 21011123 Catalytic bypass pipe "x torque" design made by m&m in Germany. The x torque design in is a true x pipe design. It is open in the center to add backpressure for torque. Give's you 10-15 ft-lbs of torque in the mid range along with 10-15 hp in the higher rpms. Why settle for the traditional cross over cat design when you can add torque in the mid range where the 996's need it most! Dme programming is necessary. Without it you will get a check engine light (cel). Tech tip: for older cars repair-kit FVD mk 996300
From $825.66
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |