Vehicles
Sections
60 not categorized PORSCHE 944 S2 REAR SEALCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 944 1982-85 (includes uncategorized and accessory items)
$33.26
Make a selection 94411691100 Does your 924 tach needle climb in high gears and not move the car like it should? Does your 924 make a grinding noise in neutral? Does your 944 seem to lurch during acceleration after shifts? These are all typical clutch problems. We offer complete packages to help you do it right! All clutch packages include clutch disc pressure plate release bearing and the always forgotten needle bearing (the little bearing in the flywheel that ruins your drive tube when it goes bad), the pilot bearing and the rear main seal. View/Change Diagram
$686.33
Make a selection FVD33150045 Original rubber replacement bushing (65 shore hardness value) for the rear control arms (camber link and caster link). This bushing cartridge is weather sealed and is crafted in high carbon steel and 7075 t6 aircraft aluminum. Sold individually.
$70.09
Make a selection FVD341999R Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with our FVD clubsport series. They are made from rubber with a 85 shore hardness value which is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This is the ideal upgrade for street and light track / clubsport use. This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes 85 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$134.24
Make a selection FVD3419991 This is a cost effective alternative to buying new control arms. Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with new bushings of the same rubber (65 shore hardness value). This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$134.24
Make a selection 91150411302EQ This one-piece seal is furthest from the rear bumper, we recommend replacing this when removing the motor for maintenance. We recommend replacing both the small and large engine seals, the large is part # 91150411102 sold individually. 1 necessary per car.
$17.82
Make a selection FVD33150020 This kit is complete and includes the front and rear monoball cartridges with press tools. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 4. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$772.20
Make a selection 92835294100 Does your car pull to one side when you hit the brakes or let go of the wheel? Do you notice one wheel seems to "get hot"? Are your calipers leaking or stuck even though you have cracked the bleeder nipples? You may need to rebuild your caliper(s). These factory kits include seals, piston clips, and boots; and with a little labor and paint, will look new as well. Reasonably priced, they sure beat the price of a new caliper! View/Change Diagram
From $27.54
Make a selection 477827529A Look at the rear hatch lock. see that gap around it? wondered what goes there? it is this piece! subjected to ultra violet damage, this piece has long ago deteriorated. replacement is as easy as a snap and you will stop the water leak. View/Change Diagram
From $6.48
Make a selection 92856426103
From $15.88
Make a selection FVD33300902AT Send us your original spring plate and we will have it reconditioned for you. The reconditioning process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and media blast the part. Once fully prepared, we install new rs spec. (85 shore) rubber bushings/bearings. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Then we seal the spring plate with a corrosion resistant plating. Sold individually. 2 necessary per car. Please note: this only fits cars with the g50 transmission.
$282.74
Make a selection PO930RBCKIT Rear; 2 required per vehicle
$52.82
Make a selection FVD33150046R Replace worn-out original soft rubber (65 shore hardness value) track rod bushings with our FVD clubsport series. They are made of rubber that has an 85-shore hardness value, the same as the rs models. 85-shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes an 85-shore hardness value core. Sold individually. 8 are necessary per car. Please note: this does not include the track rod, the picture circled in red is just for reference.
$71.28
Make a selection T55100204 Oil seal installer, flywheel end. Specially manufactured to our specifications, these tools make it easy to properly install the rear crankshaft seal. They fully support, position and press the fragile oil seal into place without distortion. For all 356 engines.
$89.05
Make a selection
$1.25
Make a selection 94451204301
From $116.42
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |