![](https://30ed524141d0cac60ab4-d2e2d18a14257de3b9ce428cf077ee97.ssl.cf2.rackcdn.com/acban.jpg)
PORSCHE CAYMAN S CHECK OUTCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 944 1982-85 - Transmission (includes uncategorized and accessory items) ![]() 90161561620EQ This is the round rubber cap that seals the door contact switch. They degrade and become brittle with age and are important as they keep moisture out of the switch. We recommend replacing both at the same time. Sold individually. Left of right side fitment.
$3.30
Make a selection 92811014711EQ Today's fuel has a myriad of oxygenate additives to comply with more strict emissions standards. These additives can be detrimental to your investment. Certain additives can break down rubber components in the fuel system. Others like ethanol are hygroscopic, so they absorb water. Ethanol is also an alcohol, so it tends to clean out more impurities which tends to foul the fuel filter far more quickly than fuels of the past. So, keeping the above in mind, we suggest replacing your fuel filter far more regularly. This is a high-quality replacement filter sourced directly from Germany. Sold individually.
$52.80
Make a selection 91152104403R01 This is for a driver's side (left hand drive) sports seat that reclines. It is the right lower outer hinge cover that does not have a knob / lever. This is a genuine part sourced from Porsche ag in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. Like new
$420.20
Make a selection 99311032701EQ Quality original style replacement filter. Are you adding this filter to a list for your next service? Please check out our engine maintenance kits, they contain everything needed to make your routine maintenance simple. Sold individually. 1 necessary per car.
$28.60
Make a selection 91151192302EQ This gasket sits on the inside of the hood in the front trunk. It tends to get nicked and cut and will degrade with time. It is essential to keep moisture out of the trunk and should be replaced at the first signs of damage. Sold individually. 1 necessary per car.
$136.40
Make a selection 911561051012EQ This is the top outer section of the cabrio top made in Germany with original sonnenland material. It is as close to the original as possible and is cut and trimmed to fit perfectly. Sonnenland material consists of 3 layers, dyed acrylic twill weave top layer, elastomeric rubber inner layer and polyester woven base layer. It provides increased strength against abrasion, increased fade resistance and the tighter woven layers are made for modern electric tops with stronger frames for the 911 and 964. Sonnenland high quality material was originally used by Porsche and other top German manufacturers. Made in Germany. This would replace original part # 911 561 051 012xw sold individually. 1 necessary per car. Only f...(choose a part on the right to read more)
$1,141.80
Make a selection 91155503156LEEQ This is an original replacement driver's side door panel that comes pre-cut with window cut outs, handle cut outs and door pull cut outs. If you have speakers that you want to retain, you must cut them yourself to size. These are a perfect diy project and can be custom tailored to match your interior options. Made in Germany. Sold individually. Please note: specific vehicle fitment below. This is not an rennsport style panel. It is intended as a direct replacement for the original.
$649.00
Make a selection 91150306203EQRB Without door post without rear lamp holder but: what you need for most quarter panel body repairs!
$1,654.40
Make a selection 93010190200EQ1 Quality aftermarket replacement, designed to perform like the original. Includes a threaded drain plug cut out, but does not include the drain plug itself. We also recommend replacing the gaskets for installation, part # 93010139101 sold individually. 1 necessary per car.
$12.10
Make a selection 93011013900EQ Today's fuel has a myriad of oxygenate additives to comply with more strict emissions standards. These additives can be detrimental to your investment. Certain additives can break down rubber components in the fuel system. Others like ethanol are hygroscopic, so they absorb water. Ethanol is also an alcohol, so it tends to clean out more impurities which tends to foul the fuel filter far more quickly than fuels of the past. So, keeping the above in mind, we suggest replacing your fuel filter far more regularly. High-quality OEM Bosch replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually.
$51.70
Make a selection 96410524707GU This fits 964 c2 / c4 and rs models with engine codes # m64.01/02/03. This is an OEM part, sourced directly from Germany. Professional installation is required. Different manufacturing tolerances require an inspection of the free clearance of all parts! If you're not sure about what parts are right for your build, be sure to ask one of our parts specialists. Sold individually. 1 necessary per car.
$932.80
Make a selection 93011007600EQ Today's fuel has a myriad of oxygenate additives to comply with more strict emissions standards. These additives can be detrimental to your investment. Certain additives can break down rubber components in the fuel system. Others like ethanol are hygroscopic, so they absorb water. Ethanol is also an alcohol, so it tends to clean out more impurities which tends to foul the fuel filter far more quickly than fuels of the past. So, keeping the above in mind, we suggest replacing your fuel filter far more regularly. This is a high quality mahle replacement filter sourced directly from Germany. Sold individually.
$19.80
Make a selection 96410524609ST This fits 964 c2 / c4 and rs models with engine codes # m64.01/02/03. This is an OEM part, sourced directly from Germany. Professional installation is required. Different manufacturing tolerances require an inspection of the free clearance of all parts! If you're not sure about what parts are right for your build, be sure to ask one of our parts specialists. Sold individually. 1 necessary per car.
$1,441.00
Make a selection 96410524609GU This fits 964 c2 / c4 and rs models with engine codes # m64.01/02/03. This is an OEM part, sourced directly from Germany. Professional installation is required. Different manufacturing tolerances require an inspection of the free clearance of all parts! If you're not sure about what parts are right for your build, be sure to ask one of our parts specialists. Sold individually. 1 necessary per car.
$932.80
Make a selection 93060610500ATK The remanufacturing process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, clean, degrease and rebuild to factory specifications. Remanufacturing is done in Germany, so the lead times can vary. Send us your original warmup regulator and we will have it remanufactured for you. We do not offer a core exchange on this part. Please note: please package your part as carefully as possible to ensure that damage is not caused en route to us.
$744.70
Make a selection 96453705700SET If you are hearing a crunching or creaking noise when you close your door, start by replacing your door check / door arrester. It prevents the door from opening to widely or slamming. As our cars age, they wear out and start to become very noisy. We also recommend replacing the door check bolt, and safety clip, so we have created an complete set for one door - repair sold individually. Left of right side fitment. 2 needed per car.
$64.14
Make a selection 96434101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for...(choose a part on the right to read more)
$418.00
Make a selection 96434705804SP We are committed to Porsche cars and are very happy to release an inner tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 032 00. We also suggest replacing your outer tie rods, part # 96434703200 (qty. 2 are needed) and now is also a good time to replace your worn out inner tie rod dust bellows, part # 96434719103. Please note: this is not for the ...(choose a part on the right to read more)
$196.90
Make a selection 96433102100RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$672.10
Make a selection 99310605180 Allows you to convert to one fan belt to run the fan and alternator like the factory rs versions. Oem part sourced in Germany to ensure quality, reliability and precise fitment. Once installed the alternator will run at the fan speed. That will lessen the inertial load and will add slightly more horsepower and acceleration. - includes fasteners (3 qty. M 6x35) - weighs .4 lbs ( .17 kg) please note: for 993 race car conversions or for cars without a/c we also recommend the corresponding crankshaft pulley, part # 99310205040 sold individually. 1 necessary per car.
From $152.90
Make a selection 96534703200SP We are committed to Porsche cars and are very happy to release an outer tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM part number, 965 347 032 00. Sold individually. 2 needed per car. We also suggest replacing your inner tie rod, we have a uniball option, our part # 96434705805sp (qty. 1 is needed) and now is also a good time to replace your worn out inner tie...(choose a part on the right to read more)
$251.90
Make a selection 96437504381 Replace your worn-out, original soft rubber engine mounts with our higher density, rs specification rubber bushing. This is manufactured of rubber with a 75-shore hardness value. 75-shore is the same density as what is used in the rs models. It is more durable, provides more positive, sharper shifts and offers crisper throttle response. Yet, rs spec rubber is still quiet and comfortable for street use. Features: sharper shifts crisper throttle response does not produce nvh (noise vibration harshness) like teflon or solid bushings rubber has a shore hardness value of 75 (like rs models) made in Germany this mount is a high-quality OEM (original equipment manufacturer) replacement part, designed to perform like t...(choose a part on the right to read more)
From $199.99
Make a selection BES98215000S2 The open architecture of this muffler allows for a deeper four-cylinder turbo tone, with plenty of whistling on tap. Coming off throttle from higher rpms exudes a chorus of snarling, gurgling and crackling letting everyone know that this car is not your average 982. + 15 hp & + 12 tq gain. - 2 x 3.5 (90 mm) round tips. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - lower deeper tones than the factory exhaust with far more whistling and gurgling / crackling off throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - no drone in the cabin. - "aero quip" style motorsport muffler connections t...(choose a part on the right to read more)
$2,816.00
Make a selection 99334101702ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install original control arm bushings. . Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for its return to you. We do not offer a core exchange on this part. Sold individually....(choose a part on the right to read more)
$418.00
Make a selection 9A160410400EQ If your starter is on its way out, you will notice an intermittent clicking noise and a delay in the vehicle starting. Eventually, you will hear a metallic screeching noise that is a sure sign that your starters bendix mechanism, bearings or solenoid are kaput. When ordering a new starter, be sure to check the protection cap on the terminal for cracks which allows moisture in and causes pre-mature failure. High-quality denso OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
$506.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |