PORSCHE 944S EFFCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 944 1982-85 - Engine (includes uncategorized and accessory items) 96437504381 Replace your worn-out, original soft rubber engine mounts with our higher density, rs specification rubber bushing. This is manufactured of rubber with a 75-shore hardness value. 75-shore is the same density as what is used in the rs models. It is more durable, provides more positive, sharper shifts and offers crisper throttle response. Yet, rs spec rubber is still quiet and comfortable for street use. Features: sharper shifts crisper throttle response does not produce nvh (noise vibration harshness) like teflon or solid bushings rubber has a shore hardness value of 75 (like rs models) made in Germany this mount is a high-quality OEM (original equipment manufacturer) replacement part, designed to perform like t...(choose a part on the right to read more)
From $199.99
Make a selection 99660610599 If you are noticing engine vibrations, misfires and even backfiring your crankshaft position sensor maybe bad. Your car's dme (ecu) uses the signal from the crankshaft position sensor to control ignition timing and fuel injection, so if your sensor is failing your engine is suffering from poor timing and is not running efficiently. This kit is complete and ready to install.
$132.75
Make a selection SNX006 Sonax gloss shampoo concentrate is a highly effective, phosphate free formula that penetrates and loosens tough dirt without damaging or stripping the protective layer. The special anionic surfactants within, simultaneously adhere and distribute dirt particles and act as emulsifiers absorbing and dissolving oil droplets. Sonax gloss shampoo concentrate is safe for all finishes and leaves a brilliant, clean shine to your paint surface every time! Simply mix two capfuls of shampoo concentrate into a 5 gallon bucket and fill with clean water. General FitmentACCESSORY
$21.50
Make a selection FVD1109114840 This replica high butterfly mfi throttle bodies system is for those looking for ultimate engine performance as well as an authentic rsr engine appearance. This kit keeps air consistently on tap for superior drivability. When the throttle is opened, there is an instant injection of air, providing a sharp, crisp throttle response. This efficient injection frees up more power and compliments larger displacements, high lift cams and full exhaust systems. This kit is engineered, precision machined, flow tested and manufactured in Germany. It is replicated to look as close to the original as possible. Intake trumpets (velocity stacks) are available in your choice of red or black. Includes: 6 individual stacks (48 mm ...(choose a part on the right to read more)
$7,456.90
Make a selection FVD50599108MM The moshammer stormforce evo rs front chin spoiler for the GTS model blends a bit of Porsche heritage into its design with canard style winglets. This effective design transforms turbulent air into a more laminar flow, creating added downforce and uplift reduction. It also incorporates twin air guides to assist with brake ventilation and underbody air flow efficiency. The moshammer stormforce evo rs front chin spoiler design offers exclusive aesthetics, aero functionality and it is secured seamlessly into the factory locations without modification. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of the s...(choose a part on the right to read more)
$1,230.90
Make a selection FVD10699712 For 997 turbo. - specially designed for tuned and motorsport vehicles the racing & high performance division of csf build and engineer the most advanced, efficient, and reliable cooling systems in the world. Csf manufacturers radiators with high performance all-aluminum and direct-fit replacement for racecars. The only high performance manufacture to feature this advanced technology. These radiators are stamped to the same geometry of the application's original plastic end radiators. These tanks feature less welding, and are generally considered the strongest tank designs in the industry.
$548.90
Make a selection FVD10699704 For 996 turbo and 997 turbo, 996 GT3l. Fits right side. - specially designed for tuned and motorsport vehicles the racing & high performance division of csf build and engineer the most advanced, efficient, and reliable cooling systems in the world. Csf manufacturers radiators with high performance all-aluminum and direct-fit replacement for racecars. The only high performance manufacture to feature this advanced technology. These radiators are stamped to the same geometry of the application's original plastic end radiators. These tanks feature less welding, and are generally considered the strongest tank designs in the industry.
$768.90
Make a selection FSPOR992TVLV Treat your 992 turbo to the finest cat-back exhaust solution on the market. This valveed exhaust system is plug-and-play with the factory pse system so you can turn pse off for quiet highway cruising and turn pse on for ripping twin turbo sports car sound!
$5,245.95
Make a selection SNX005 Sonax high speed wax is a highly effective protective spray wax that is easy to apply and long lasting. The breakthrough nanotechnology wax formulation includes a blend of microscopic carnauba wax (protection) and a special silicon emulsion (shine) that delivers a streak-free, high-gloss finish. Sonax high speed wax is also ideal for maintaining and protecting plastic convertible tops. General FitmentACCESSORY
$15.95
Make a selection SNX002 Sonax premium class paint cleaner is the optimum abrasive polish for preparation of a paint surface. It is a silicone-free paintwork cleaner that safely and effectively degreases the paint surface and removes smear films caused by silicone, oil and wax deposits. Sonax premium class paint cleaner contains nanotechnology-refined, high-end alumina which ensures a smooth and consistent polishing effect. New paintwork surfaces are gently made to shine without producing holograms or other unwanted polishing structures. It is ideal for the care and maintenance of scratch resistant ceramic clear coats. It will considerably increase the durability of a follow up sealing or protecting treatment (i.e. Sonax premium class ...(choose a part on the right to read more) General FitmentACCESSORY
$28.95
Make a selection FVD1109115043 This replica high butterfly mfi throttle bodies system is for those looking for ultimate engine performance as well as an authentic rsr engine appearance. This kit keeps air consistently on tap for superior drivability. When the throttle is opened, there is an instant injection of air, providing a sharp, crisp throttle response. This efficient injection frees up more power and compliments larger displacements, high lift cams and full exhaust systems. This kit is engineered, precision machined, flow tested and manufactured in Germany. It is replicated to look as close to the original as possible. Intake trumpets (velocity stacks) are available in your choice of red or black. Includes: 6 individual stacks (50 mm ...(choose a part on the right to read more)
$7,456.90
Make a selection FVD10699601 For 986 (Boxster) and 996 modell. Fits left and right side. - specially designed for tuned and motorsport vehicles the racing & high performance division of csf build and engineer the most advanced, efficient, and reliable cooling systems in the world. Csf manufacturers radiators with high performance all-aluminum and direct-fit replacement for racecars. The only high performance manufacture to feature this advanced technology. These radiators are stamped to the same geometry of the application's original plastic end radiators. These tanks feature less welding, and are generally considered the strongest tank designs in the industry.
$548.90
Make a selection 96410541903EQ When working on your cylinder head, we recommend replacing the valves, valve seat rings, guides, springs, retainers and temperature sensor at the same time to reduce future labor costs. Cost effective, German made exhaust valve for the 964 c2 / c4 and rs that have the m64.01/02/03 motors. Sold individually. 6 necessary per car.
$64.90
Make a selection FVD33396410 A cost effective FVD exclusive combination of bilstein clubsport shocks with a set of eibach pro kit springs. This suspension kit is meant for those who want the car to sit at the lowest possible ride height. This set up will allow you to lower the front axle by 2.4 inches (60 mm). This is a perfect kit for clubsport or race use where the surfaces are smooth and even. The stock rs ride height was 1.6 inches (40 mm) lower. So, this is a full 3/4 of an inch (20 mm) lower on the front axle. Sold as a complete kit. 1 kit is necessary per car. Please note: we recommend the b6 / ohlins suspension kits for those looking for more comfort for street use.
$2,726.53
Make a selection FVD33396500 A cost-effective combination of bilstein b6 shocks with a set of German h&r lowering springs. This kit is a perfect balance of performance and comfort for street use. Benefits: optimum adhesion and enhanced stability for daily driving and extreme driving situations. Lower stance at 1.3 inches (35 mm) front / 1.18 inches (30 mm) rear. Marked improvement in safety and sportiness. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Please note: if you would like to reduce the ride height, please order part # 115110016 which will lower the stance by another 1.5 inches (40mm).
$2,730.94
Make a selection FVD33396401 A cost-effective combination of bilstein b6 shocks with a set of German h&r lowering springs. This kit is a perfect balance of performance and comfort for street use. Benefits: optimum adhesion and enhanced stability for daily driving and extreme driving situations. Slightly lower stance at 1.3 inches (35 mm) front / 1.18 inches (30 mm) rear. Marked improvement in safety and sportiness. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Please note: if you would like to reduce the ride height, please order part # 115110016 which will lower the stance by another 1.5 inches (40mm).
$2,538.53
Make a selection FVD3419991 This is a cost effective alternative to buying new control arms. Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with new bushings of the same rubber (65 shore hardness value). This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection FVD50599102MM The moshammer evo 2 front chin spoiler blends a bit of Porsche heritage into its design with canard style winglets. This effective design transforms turbulent air into a more laminar flow, creating added downforce. Porsche active aerodynamics remains fully functional in all 3 positions and the evo 2 chin spoiler secures seamlessly into the factory locations. The evo 2 spoiler's design offers a more aggressive look but also blends perfectly with other design elements like the side skirts and rear spoiler. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of either the evo rs (991.2 turbo/s) or downforce rs...(choose a part on the right to read more)
$1,386.00
Make a selection FVD51299124MM The moshammer stormforce evo rs rear spoiler for the 991.2 model blends a bit of Porsche ducktail heritage into its design to increase rear downforce and reduce front axle uplift. The contours of this spoiler have a step effect which seamlessly blends into both rear quarter panels. When viewed at a standstill it has a subtle factory like appeal that complements the cars lines. When deployed the rake angle takes on a more aggressive appearance evoking thoughts of the much beloved ducktails. Like a majority of the moshammer offerings, this spoiler is a direct replacement, so it secures seamlessly to the factory locations with the original hardware. This is an ideal addition for a leased vehicle or for those looki...(choose a part on the right to read more)
$1,455.30
Make a selection 96434307181ATK Looking for a more cost-effective solution than ordering a new link? Let us recondition your original drop link. The reconditioning process includes full inspection, disassembly, degreasing and media blasting. Once fully prepared, we properly install new bushings, finish with a corrosion proof coating and include a new lock nut. Please note: each link is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your link we will notify you as soon as we can. Arrangements can be made for its return to you. Sold individually. 1 necessary per car.
$194.70
Make a selection FVD890964228 We recommend changing your ignition cables when changing your plugs and distributor. Overlooking the ignition cables can lead to increased resistance and weak spark which causes incomplete combustion in the cylinder and robs your engine of power and efficiency. Also, check your cable clips, part # 96460255900 and wire guide, part # 91160232500, they wear with time and now is the perfect time to change them. Sold as a complete set. Be sure to check the "fits these models" tab to make sure that this will work for your needs.
$685.30
Make a selection FVD6314051 Now we can offer you OEM quality clear turn signals. We have sourced these from Bosch in Germany directly. Bosch is a worldwide leading developer and manufacturer of automotive technology. They represent maximum quality and reliability and go above and beyond any minimum legal specifications. These turn signals are e-1 certified in Germany. They will not fade and discolor with time like those on the market in the past. The set includes 2, 12v 21 watt amber bulbs to meet road regulations. If you would like a clear set of bulbs that flash amber, order part # FVD631752 sold as a set. 1 necessary per car. Please note: these are euro spec turn signals so the flat reflectors hole for the bulb holder is not cutout. Eu...(choose a part on the right to read more)
$324.50
Make a selection FVD50399101MM The moshammer front fender set blends just the right amount of motorsport pedigree with functionality. This aggressive design is captivating on any 991 model and offers a level of exclusivity not found with competitors body kits. The integrated fender vents lower the thermal load on the brakes by allowing the heat to be quickly ventilated up and out of the wheel arch. This composite fender set has been meticulously designed to bolt up to the factory locations for perfect panel fitment, alignment and consistent gaps. A perfect addition for a leased vehicle or for those looking to return the car to its original appearance in the future. These fenders complement the entire moshammer stormforce (991.1) / stormforce...(choose a part on the right to read more)
$3,631.10
Make a selection BES99722240BES Brombacher 997.2 tt "sport " stainless steel, sport cat converter replacements for our bes- muffler facts: - + 21 crank hp & + 18 crank torque** - 200 cell "hd", tri metal German hjs sport catalysts - tubing diameter is the same as the OEM system. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - reduces backpressure and thermal stress - 5 on a scale of 1-10 in volume (1 being stock). - reuses OEM v band style connecting hardware. - made in Germany. - available in 100 cell and cat bypass. Please ask your sales person for pricing. - more distinguished growl at idle, partial throttle and wide open throttle. - dme programming not necessary. - reuses OEM ti...(choose a part on the right to read more)
$4,303.20
Make a selection 99919235250EQ Belts undergo a lot of friction and wear. They are cost effective to change and will keep your engine and accessories in good condition. Be sure to follow recommended service and replacement intervals set by Porsche on belts. Please note: specifically fits 964 c2 / c4 and rs up to 1992 with the corresponding m64.01/02/03 engine codes. Sold individually. 1 necessary per car.
$24.20
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |