PORSCHE 964 PARTSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 944 1982-85 - Electrical (includes uncategorized and accessory items) 6425 The 6al delivers everything the 6a does with the addition of a built-in soft touch rev control. This feature allows you to set an rpm limit to protect the engine from over-rev damage caused by driveline failure or missed shifts. Other msd rpm controls can be connected to the 6al such as a three step module selector or rpm activated switch . The 6al also comes supplied with rubber shock mounts and 3000, 6000, 7000, 8000, rpm modules. All necessary parts and wiring instructions are included. General Fitment911 1987-89911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1965-69 944 1989-91 944 1985-88 944 1982-85 924 1986-88 924 1980-85 924 1976-79 914 1970-76 912 1965-69 911 1989-94
$358.00
Make a selection 911561023606EQ This is a complete cabrio top cover made in Germany with original material. It is as close to the original as possible and is cut and trimmed to fit perfectly. Includes all of the original tenax snaps / retainers in the original locations. This would replace original part # 911 561 023 60 6ha made in Germany. Sold individually. 1 necessary per car.
$1,321.10
Make a selection 93010090104EQ High-quality victor reinz replacement gaskets, o-rings and washers to reseal your engine case (short block). Victor reinz has been supplying German auto manufacturers and Porsche for decades. They are a trusted name in gaskets and sealing products. This kit is complete with everything needed and we source this directly in Germany for an added level of quality. Sold individually. 1 set necessary per car. Please note: if you prefer the genuine crankshaft sealing ring, please order part # 99911342641 this also includes the intermediate shaft o-ring, part # 99970731540. Please check the model fitment tab to ensure accurate fitment.
$118.80
Make a selection 91155507860700R01 Genuine part sourced in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. Like new
$150.00
Make a selection 911561050002FA1 We go to extra lengths to ensure that our linings are as similar to the originals as possible. Each is cut and trimmed to fit perfectly. Replaces original part # 911 561 050 002 fx made in Germany. Sold individually. 1 necessary per car. Please note: specific model fitment below.
$177.10
Make a selection 9115550551570EQ Quality replacement headliner for original number, 911 555 055 157 00. This is made by dansk, they offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality, factory fitment and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Sold individually. 1 necessary per car.
From $192.50
Make a selection 95011623712EQ When the clutch pedal is depressed, the hydraulic pressure from the master cylinder engages a piston in the slave cylinder to actuate the clutch fork to release your clutch. If the slave cylinder develops a leak or fails, you will not be able to engage or disengage the clutch to shift gears. Sold individually. 1 necessary per car. We also recommend installing our stainless clutch hose, part # FVD42347700
$126.50
Make a selection 146096479 Thermo-tec snap straps General FitmentALL
$30.45
Make a selection 22011090102ATK Sport throttle bodies are a great addition for those with highly modified cars. They are a great addition for those with full exhaust systems (larger diameters), maf kits, larger displacements, street or race cams, etc. The remanufacturing process includes full inspection of your throttle body to ensure proper operation after the remanufacturing process. We then disassemble and bore the original to a 2.7-inch (70.5 mm) diameter. The entire throttle body is cleaned, degreased and the internals are polished to create more laminar flow. We then machine the shaft to accept larger butterfly's which seamlessly match the bore. All clearances are checked for precision to ensure reliability. Each throttle body is reman...(choose a part on the right to read more)
$589.60
Make a selection 93021123801EQ This part is sourced in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
$139.70
Make a selection 93010314781SET Oem parts, sourced directly from Germany. Sold individually. 1 necessary per car.
$366.30
Make a selection KEV53100601 Made in europe by one of the manufacturers to Porsche. Extremely high-quality kevlar / carbon door that includes every detail for a perfect fit. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight 4 kg (8.81 lbs) - kevlar / carbon - mounting is just like factory, no modifications are necessary. ** does not include the inner protection bar please note: these are high quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world. Hinges are not provided; original hinges must be used. Please let us know the year and model and if you intend to use electric windows and electric...(choose a part on the right to read more)
$3,285.70
Make a selection 444552985051 This is a carbon overlay, meant to be adhered to your original plastic instrument trim. We recommend adhering the carbon overlay to your original with wurth bond and seal (sold separately). Great detail is taken to attempt to match the original weave size, color and polish. Whether you are adding carbon to the interior or matching existing pieces, this is high quality and is made in Germany so it is made to last, like the original. This cover is a carbon overlay to be adhered to the original black plastic piece, part # 911 552 550 00 700 for reference. Sold individually.
$640.20
Make a selection 96560612601EQ Oxygen or lambda sensors are critical to your engines health. If the sensor is faulty you may experience poor gas mileage, rough idling or engine pinging. High-quality replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Be sure to check the "fits these models" tab to make sure that this will work for your needs. Sold individually. 1 necessary per car.
$111.10
Make a selection FVD803993VR0222 High quality, German made three-point replacement safety belt, designed to perform like the original. Features / specs: belt length: 300 cm (118 inches) 3 point inertia reel belt angle adjustable reel (max. Of 8 *) includes 22 cm (8.5 inch) buckle, installation hardware and caps. Din-en-iso 9001: 2000 quality standard manufactured, e-mark approved. The matching rear belt is part # FVD803993hr sold individually. 2 necessary per car.
$187.00
Make a selection KEV503032011 Made in europe by one of the manufacturers to Porsche. Extremely high-quality kevlar / carbon fender that includes every detail for a perfect fit. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight 5.9 lbs. (2.68 kg) - made of high strength kevlar and carbon. - mounting is just like factory, no modifications are necessary. Please note: these are high quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world.
$1,215.50
Make a selection 96410090200EQ FVD cylinder head gasket sets contain high quality German sourced gaskets, seals and o-rings. This kit contains a complete set of gaskets to make a teardown / rebuild more convenient. Sold as a complete set. 1 necessary per car. To complete the gasket set for the whole engine please order part # 93010090104eq
$387.20
Make a selection HEI964001005S Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long-standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: bolt-in bar - screwed in to the original seat belt points chromoly steel 1.5-inch diameter tubing, .098 wall thickness tubing. Bars which connect to the main hoop, use a connecting joint system. Tig welded. Retains full seat adjustability. Semi-gloss black finish. Cost effective for club sport ...(choose a part on the right to read more)
$1,284.80
Make a selection FVD803993HR High quality, German made replacement lap safety belt, designed to perform like the original. Features / specs: includes buckle, installation hardware and caps. Din-en-iso 9001: 2000 quality standard manufactured, e-mark approved. The matching front belt is part # sold individually. 2 necessary per car.
$187.00
Make a selection 96420713004EQ This connects to the side of the oil tank. We recommend replacing 2 qty. Clamps, part # 99951235602 when replacing this piece. Sold individually. 1 necessary per car.
$11.00
Make a selection 964347009BXATK This steering rack is a remanufactured part with a core, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and resell-able, the core deposit will be refunded. The remanufacturing process includes full inspection and testing for structural integrity. We then disassemble and bead blast to remove corrosion. Internals are micro-finished to OEM specifications. Sealing surfaces are carefully checked and restored prior to installing new premium seals and o-rings. Each unit is then carefully tested for full functional...(choose a part on the right to read more)
$1,633.50
Make a selection 96434101707AT By ordering this article number, you will receive a reconditioned wishbone with newly pressed-in bearings. The calculated replacement deposit will be returned to you as soon as the old part has been received and checked. This item is also available with race bearings (85 shore).article number FVD 341 017 07at the reconditioning process includes full inspection of each track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. If your old part is not repairable we will inform y...(choose a part on the right to read more)
$418.00
Make a selection 96411122380R02 All motorsport and racing parts are special order items. Special order items must be paid for in advance. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis and do not carry any warranty. No exceptions. Leichte lagerspuren
$201.99
Make a selection 964555251000EQ Attention to detail is what distinguishes our parts from the competition. We source these door handles in Germany to ensure that they are made as closely to the original as possible. Sold individually.
$95.46
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |