PORSCHE 996 TURBO POSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 928 1992-95 - Brakes/Wheels (includes uncategorized and accessory items) FVD351997TTCS This kit convert's the 997 turbo pccb rotors to steel rotors with yellow pagid pads.( only 5-hole, not central lock ) this system is complete with everything that you need to install. Do not ruin your expensive ceramic brake discs on the track. Get ready for racing with the original and much cheaper Porsche motorsport steel brake discs! What's in the box: 4 x 2-piece brake discs (380 x 34 mm - front / 350 x 28 mm - rear) 4 x wear sensors 2 x set ( front and rear ) brake pad set (pagid yellow - rs29 ) 8 x screws for brake caliper 8 x damping plates technical tip: also order stainless steel brake lines (FVD b96 355 97) and racebrake fluid (012 145 ca).
$6,852.38
Make a selection FVD35117 Bei 944 s2 nur mit sportfahrwerk m030 koni sporting lookbetter coolingremoves wetness and contamination fast General Fitment944 1982-85944 1985-88 928 1992-95
From $208.28
Make a selection FVD50399101MM The moshammer front fender set blends just the right amount of motorsport pedigree with functionality. This aggressive design is captivating on any 991 model and offers a level of exclusivity not found with competitors body kits. The integrated fender vents lower the thermal load on the brakes by allowing the heat to be quickly ventilated up and out of the wheel arch. This composite fender set has been meticulously designed to bolt up to the factory locations for perfect panel fitment, alignment and consistent gaps. A perfect addition for a leased vehicle or for those looking to return the car to its original appearance in the future. These fenders complement the entire moshammer stormforce (991.1) / stormforce...(choose a part on the right to read more)
$3,921.59
Make a selection BBI9964010002 Finally, a complete solution to properly widen the front track width of a Porsche 996 and 997 turbo. To help increase front end grip, this kit allows full negative camber adjustment without binding the axles and fitment of wider wheel/tire combinations and GT3 cup car fenders. Each kit includes lower control arms, thrust arms, axle spacers, upper mounts, and camber shims.
$3,990.60
Make a selection FVD35118 Bei 944 s2 nur mit sportfahrwerk m030 koni sporting lookbetter coolingremoves wetness and contamination fast General Fitment944 1982-85944 1985-88 928 1992-95
From $208.28
Make a selection FVD351997GT2CS2 This kit convert's the 997 turbo GT2's / 997gt3 rs pccb rotors to 997 GT3 cup car steel rotors with green cup car pads ( for cars with central lock only ) this system is complete with everything that you need to install. Do not ruin your expensive ceramic brake discs on the track. Get ready for racing with the original and much cheaper Porsche motorsport steel brake discs! What's in the box: 4 x 2-piece brake discs (380 x 34 mm - front / 350 x 28 mm - rear) 4 x wear sensors 8 x cup brake pads (racing green) 8 x screws for brake caliper 8 x damping plates technical tip: also order stainless steel brake lines (FVD b96 355 97) and racebrake fluid (012 145 ca).
$7,894.26
Make a selection BES99125010SK Are you one of those that are looking for more sound from your Porsche sport exhaust (pse)? Perhaps it's not quite as aggressive as you would like, or your last Porsche just sounded so much better? Don't worry, we have you covered, and the beauty is, you don't have to touch the catalytic converters which is a big no, no with Porsche dealers. With the valves open you receive a far more exotic, rich, deep, turbo motorsport tone and with the valves closed, soft subtle, completely stock sounds. So, absolutely no compromise and you will be thinking, the car really should have left the factory like this! Features: - + 10 crank hp & + 8 crank torque. - weighs 29 lbs. (13 kg) - German v2a - x5crni18-10 - 1.4301 stai...(choose a part on the right to read more)
$5,218.88
Make a selection BES99120040S Take your 991.1 or 991.2 turbo or turbo s to a new level with these muffler bypass pipes. They produce the wildest sound available on the market today and are a perfect upgrade for level 3 or 4 car used on the track. They produce loud, low, deep tones with exaggerated turbo whistling and sinister gurgling and crackling off throttle. By far the best sound you can get out of your turbo, not to mention being able to shoot flames! The only real drawback is the drone in the cabin which we try to minimalize by stepping down the diameter in 3 stages. Features: - + 35 crank hp & + 25 crank torque - 3 tubing (75mm) that tapers down to 2.25" (57mm) to prevent turbo damage. - weighs 7 lbs. (3,1 kg) - German v2a - x5crni1...(choose a part on the right to read more)
$725.87
Make a selection FVD504993RS Made of polyurethane so they will not chip or crack like fiberglass, and are flexible enough to survive small impacts. Simple installation without any modifications to the original bodywork. Sold as a set (left and right). Not for wide body cars (993 turbo or turbo-look). Please note: these are aftermarket products. All aftermarket products need to be prepped, sanded, gaps checked / filled and painted. We only recommend professional installation with a shop that has aftermarket bodywork experience.
$752.00
Make a selection BES99715040S2 Quiet version with catalytic bypass and 4x80mm end tips these versions of FVD sport exhaust system is specifically made for increased performance vehicles. Designed for tolerable, pleasant and sonorous sound (especially for the turbo cabriolet). The elimination of the catalysts reduced drastically the back pressure and increases the performance and throttle response to the max! - stainless steel exhaust system - catalytic bypass - 4x80mm end tips - 2 3/4 tubing (70mm) straight through design for maximum power - weighs 39 lbs. (18,1 kg) - made in Germany - dme programming necessary (catalytic adaption) - stock tips will fit. Tech tip: order also repair / gasket set FVD mk9 970 02
$3,162.46
Make a selection 99310117054 This is the original stud used in the rennsport and turbo (m64.20 / 60) models. We recommend them for your next engine rebuild. Sold individually. 24 necessary per car.
From $58.21
Make a selection 99312301352ATK Our k-16 remanufactured turbo is cost competitive and is a direct replacement. Simply send us your original k16 turbochargers and a borg warner / kkk certified technician will remanufacture your turbo. The remanufacturing process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will replace the turbine wheels, thrust bearings, install new seals, install new waste gates, recondition the internals and high speed balance the turbo. This ensures reliability and superior performance for many years to come. The remanufacturing is done on an exchange basis only. You must send us your original k16 turboc...(choose a part on the right to read more)
$2,370.06
Make a selection BES98215000S The open architecture of this muffler allows for a deeper four-cylinder turbo tone, with plenty of whistling on tap. Coming off throttle from higher rpms exudes a chorus of snarling, gurgling and crackling letting everyone know that this car is not your average 982. + 15 hp & + 12 tq gain. - 2 x 3.5 (90 mm) round tips. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - lower deeper tones than the factory exhaust with far more whistling and gurgling / crackling off throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - no drone in the cabin. - "aero quip" style motorsport muffler connections t...(choose a part on the right to read more)
$3,636.47
Make a selection 129T851846 The rh turbo style Porsche wheel is a classic design perfectly suited for any Porsche model. The center section is cast aluminum and finished in a silver paint. The wheels come with standard rh center cap and accept factory Porsche wheel bolts and center caps. The wheels are offered in 17 and 18 with a variety of offsets to fit narrow and wide body Porsche applications. These wheels are made to order and take between 1-3 weeks to deliver. We recommend ordering a set of rh valves, part # 12945281 when ordering this wheel. Sold individually.
$369.47
Make a selection 930123002X This remanufactured turbo is a direct replacement for original part # 930 123 002 00. The remanufacturing is completed in Germany by kkk/borg warner certified technicians. This ensures reliability, superior performance and cost effectiveness. The remanufacturing process includes: complete disassembly. All parts are cleaned, inspected and measured for tolerances. Turbine wheels are replaced. Thrust bearings are replaced. All new seals are installed. Internals are reconditioned. Parts are balanced (static & dynamic) according to balancing protocol. For a complete installation we recommend adding a gasket, part # 93012319105 an intake sleeve, part # 93011015801 and be sure to have a few spare studs on hand, part #...(choose a part on the right to read more)
From $3,220.28
Make a selection 129T101840 The rh turbo style Porsche wheel is a classic design perfectly suited for any Porsche model. The center section is cast aluminum and finished in a silver paint. The wheels come with standard rh center cap and accept factory Porsche wheel bolts and center caps. The wheels are offered in 17 and 18 with a variety of offsets to fit narrow and wide body Porsche applications. These wheels are made to order and take between 1-3 weeks to deliver. We recommend ordering a set of rh valves, part # 12945281 when ordering this wheel. Sold individually.
$482.33
Make a selection 00004400057 Smooth-fitting indoor car cover featuring full-color Porsche logo. Designed for use out of the weather, as indoor protection from dust and dirt. Made from a breathable, antistatic material, features full-color Porsche logo. General FitmentACCESSORY
$550.29
Make a selection 96434703200SP We are committed to Porsche cars and are very happy to release an outer tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 032 00. This is ideally suited for use with our monoball inner tie rod, part # 96434705805sp for the 964 c2 / turbo look or 965 or part # 96434705804sp for the 964 c4 or rs. Please note: this is not for the wide body. Sold indiv...(choose a part on the right to read more)
$341.51
Make a selection FVD34791130 Enhance steering precision and steering feedback by simply replacing your original tie rods. Turbo tie rods use a spherical inner joint instead of soft rubber bushings. They offer quicker steering response, more sensitivity and more precision. These are standard length we highly recommend them for lowered vehicles with bump steer kits like part # FVD34791100 or FVD347911930 . We also offer turbo tie rods in longer lengths for other applications, check part # FVD34791180r and FVD34791181ry this kit is manufactured in Germany by an OEM supplier, made from high carbon steel and 7075 t6 aluminum. Kit includes: 2 qty. Outer tie rods 2 qty. Inner tie rods 2 qty. Spacing washers 2 qty. Boots 2 qty. Castle nuts 2 qty. ...(choose a part on the right to read more)
$240.02
Make a selection 90110705903 The new oil cooler for the Porsche 914-6 is based on the incredibly popular and successful csf 911/930 turbo engine oil cooler (csf #8242). Both of these oil coolers went through 2+ years of development and multiple rounds of prototypes. The csf Porsche 914-6 engine oil cooler’s world debut at rennsport reunion 2023 was met with incredible support and enthusiasm from the community. Obviously air-cooled enthusiasts know the struggles associated with the oil cooler located on the engine block of the old flat six motor. With the 914-6 swaps/conversions becoming ever more popular, this new oil cooler will be a game changer for classic Porsche owners and restoration shops.
From $1,112.40
Make a selection 96434705804SP We are committed to Porsche cars and are very happy to release an inner tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 032 00. We also suggest replacing your outer tie rods, part # 96434703200 (qty. 2 are needed) and now is also a good time to replace your worn out inner tie rod dust bellows, part # 96434719103. Please note: this is not for the ...(choose a part on the right to read more)
$212.65
Make a selection FVD11103901 These headers are meant to replace the original 993 GT2 r (993 111 039 83) headers that are no longer available. They will reduce turbo lag and add horsepower and torque. Made of t316 stainless. Primaries are 42mm (1.65 ). Merge into a 50mm (2 ) motorsports collector. Manufactured by m&m exhaust in Germany.
$1,982.77
Make a selection F9664120202TT This is for the 996 turbo model with logo in center tach. The differences are day and night! Gauge faces are one of the most visible and frequently looked at components in your Porsche. Why skimp on quality? Gauge faces should have clearly visible markings and be easy to read with and without back lighting. Replacement faces should offer similar qualities, but many gauge faces on the market don't quite make the grade. FVD gauge faces are different. What makes them different you ask? See for yourself. In the below pictures you will see that the tiptronic is an FVD gauge face and the 6 speed gauge face is the competitions. The daytime difference (the competition): darker, more yellow appearance raised orange war...(choose a part on the right to read more)
$533.41
Make a selection FVD10397501CARR Connecting rod with plc carr-6 screw. The s connecting screw (plc carr-6) needs only every third time to be changed under race conditions or motor sport use when overhauling the engine. When used in 997.1turbo connecting rod bearing 99310314715set must be used (tongue / nose opposite). Carrillo is one of the most respected connecting rod manufacturers in competitive motor sports. Carrillo rods are constructed from their propriety alloy and forged to their custom specifications. The rods are then fully machined to guarantee the removal of all surface imperfections. After heat treatment, each connecting rod is magnaflux inspected and hardness checked, then machined to final size. Each set is balanced and then sho...(choose a part on the right to read more)
$3,188.59
Make a selection FVD123025ATK K24/26 exchange turbo (only OEM k24 exchange accepted) (up to 700 hp) power is focused on mid and top range rpm's. Facts: - modified compressor housing and backing plate - modified & lightened high flow compressor wheels. - remanufactured by kkk / borg warner certified technicians - free software update for those already running FVD software. FVD brombachers 996 k24/26 race turbos are new units created for those who are looking for ultimate in performance. Power is focused in the mid and top rpm range while keeping turbo lag low. They are completely bolt on and do not require custom headers or special modifications. The factory OEM turbocharger compressor housing is re-profiled and the compressor backing plate...(choose a part on the right to read more)
$3,214.73
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |