Vehicles
Sections
169 not categorized PORSCHE CAYMAN ELYCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 928 1983-86 (includes uncategorized and accessory items) 99919217350EQ A severely worn a/c belt will no longer be able to grip the pulleys and will start to slip and cause a loud squealing noise when the a/c is turned on. Belts undergo a lot of friction and wear. They are cost effective to change and will keep you're a/c functioning properly. Be sure to follow recommended service and replacement intervals set by Porsche on belts. High-quality OEM Bosch replacement belt, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
$20.20
Make a selection 99334101802ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install original control arm bushings. . Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for its return to you. We do not offer a core exchange on this part. Sold individually....(choose a part on the right to read more)
$462.13
Make a selection AP958170 Agency power is proud to release its super sport exhaust system for the 958 Porsche Cayenne s v8 2011 and up. the super sport exhaust is a axle system that gives your 4.8l v8 engine a real aggressive tone. made here in the usa, the exhaust saves close to 30lbs off the rear end of the vehicle. using 304 stainless steel and detail oriented tig welding, the exhaust system uses two small high flow mufflers which give it the sports car rumble. its reduced back pressure design gives the engine improved horsepower and torque with most noticeable improvement in throttle response. because of the reduced restriction, this exhaust horsepower gains can definitely be noticed in the mid to top rpm range.
$1,615.63
Make a selection ADVWSSDXL Perfect gear to show off your tuner of choice at a windy track day or race event. This German made, wind and water proof soft shell jacket is available in black or white. It includes grey color contrasts with the FVD logo stitched in red on the collar, left chest and right arm. There are plenty of pockets with waterproof zippers to safely store personal items and electronics.
$160.38
Make a selection BBI9118170001 The bbi autosport race spec seat mounts are a direct bolt into the factory mount location for a hassle free, easy installation for your competition race seat. The bbi autosport seat mounts have a large range of adjustment options allowing fitment for all major fia and sfi approved seat brands and offers an integrated 5 and 6-point sub belt mounting location. The wide range of adjustment covers almost all possible seating preferences to properly seat drivers of all sizes. Cad designed, cnc laser cut and formed from one piece of .125” (1/8”) carbon steel with no welds to maximize strength and stiffness. All mounts are powder coated with a wrinkle black base and satin black sides.
$426.60
Make a selection BBI9912020003 The bbi autosport 997 & 991 GT3 / rs exhaust side bypass is a direct replacement for the factory primary side mufflers. The primary mufflers are weigh approximately 44 pounds total while the bbi pipes are 4 pounds in comparison. For durability and protection against corrosion, each system is meticulously tig welded using 304 aerospace grade stainless tubing with lower carbon content. The result is a substantial reduction in weight behind the rear axle which significantly improves handling and less restriction to produce a much more aggressive exhaust note.
$1,026.00
Make a selection BBI9964010006 Finally, a solution that allows you to safely increase without the risk of damaging your front axles. as you add GT3 shims to your front Porsche 996/997 turbo lower control arms, you move the cv joints beyond their safe range of motion, risking failure and expensive damage. These 10mm thick precision spacers, used with 16mm of lca shims will provide an additional -1.7 deg. Of camber, while maintaining the factory cv joint and axle relationship. the spacer design features a concentric lip that positively and accurately locates it to the cv joint for perfect balance and no vibration. Each kit includes two spacers and all the needed hardware in high class 10.9 grad
$405.00
Make a selection BEC911930SGT Brombacher exclusive covers are completely manufactured in the south of Germany in baden wurtemberg, between stuttgart and our local mountains in the southern black forest. The materials chosen is environmentally friendly production and each stich is made with care. 100% Germany quality, perfect, personalized appearance for every taste, even in the covered state a mixture of cotton and polyester nano-coated on the outside which makes it so dirt and water repellent, completely paint-friendly, with very breathable construction. Price includes: cover color selection, color selection of trim, custom embroidered logo and a matching bag with a small custom logo, in the same colors. Please let us know what model, year...(choose a part on the right to read more)
$943.27
Make a selection BEC911964BBC Brombacher exclusive covers are completely manufactured in the south of Germany in baden wurtemberg, between stuttgart and our local mountains in the southern black forest. The materials chosen is environmentally friendly production and each stich is made with care. 100% Germany quality, perfect, personalized appearance for every taste, even in the covered state a mixture of cotton and polyester nano-coated on the outside which makes it so dirt and water repellent, completely paint-friendly, with very breathable construction. Price includes: cover color selection, color selection of trim, custom embroidered logo and a matching bag with a small custom logo, in the same colors. Please let us know what model, year...(choose a part on the right to read more)
$943.27
Make a selection BEC993001GSOH Brombacher exclusive covers are completely manufactured in the south of Germany in baden wurtemberg, between stuttgart and our local mountains in the southern black forest. The materials chosen is environmentally friendly production and each stich is made with care. 100% Germany quality, perfect, personalized appearance for every taste, even in the covered state a mixture of cotton and polyester nano-coated on the outside which makes it so dirt and water repellent, completely paint-friendly, with very breathable construction. Price includes: cover color selection, color selection of trim, custom embroidered logo and a matching bag with a small custom logo, in the same colors. Please let us know what model, year...(choose a part on the right to read more)
$943.27
Make a selection BES91105000S This muffler was specifically designed for a backdate to the st look. It is manufactured for mid-range and top end performance, all without drone inside the cabin. It seamlessly mates to ssi heat exchangers for added performance while keeping the cabin warm in the winter. The muffler is vastly different than the common baffle plated mufflers stuffed with packing material that are common in the aftermarket. Ours are uniquely made with double perforated sound absorption tubes based on the halbgegenstromprinzip (half counter current principle). The acoustic silencer absorption tubes are made in a trapezoidal pattern and are perforated with varying diameters, which isolate and dampen the unwanted frequencies that c...(choose a part on the right to read more)
$2,838.13
Make a selection BEC997001SWOH Brombacher exclusive covers are completely manufactured in the south of Germany in baden wurtemberg, between stuttgart and our local mountains in the southern black forest. The materials chosen is environmentally friendly production and each stich is made with care. 100% Germany quality, perfect, personalized appearance for every taste, even in the covered state a mixture of cotton and polyester nano-coated on the outside which makes it so dirt and water repellent, completely paint-friendly, with very breathable construction. Price includes: cover color selection, color selection of trim, custom embroidered logo and a matching bag with a small custom logo, in the same colors. Please let us know what model, year...(choose a part on the right to read more)
$856.55
Make a selection BEC997GT225J Brombacher exclusive covers are completely manufactured in the south of Germany in baden wurtemberg, between stuttgart and our local mountains in the southern black forest. The materials chosen is environmentally friendly production and each stich is made with care. 100% Germany quality, perfect, personalized appearance for every taste, even in the covered state a mixture of cotton and polyester nano-coated on the outside which makes it so dirt and water repellent, completely paint-friendly, with very breathable construction. Price includes: cover color selection, color selection of trim, custom embroidered logo and a matching bag with a small custom logo, in the same colors. Please let us know what model, year...(choose a part on the right to read more)
$654.59
Make a selection BES91105000SST This muffler was specifically designed for a backdate to the st look. It is manufactured for mid-range and top end performance, all without drone inside the cabin. It seamlessly mates to ssi heat exchangers for added performance while keeping the cabin warm in the winter. The muffler is vastly different than the common baffle plated mufflers stuffed with packing material that are common in the aftermarket. Ours are uniquely made with double perforated sound absorption tubes based on the halbgegenstromprinzip (half counter current principle). The acoustic silencer absorption tubes are made in a trapezoidal pattern and are perforated with varying diameters, which isolate and dampen the unwanted frequencies that c...(choose a part on the right to read more)
$2,771.60
Make a selection BES98115000S This is a forum favorite for the best sound with minimal drone! This muffler really does everything so well. Civilized while cruising, a beast under load and cup car gurgles and crackles off throttle. + 11 hp & + 10 tq gain. - weighs 35.4 lbs - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - 2 1/2 tubing (63.5 mm). - 2 x 3.5 (90 mm) round tips. - intoxicating growl at idle, partial throttle and wide open throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - minimal resonance / drone in the cabin (200 rpms worth) compared to the competition's mufflers. This can be verified on the forums like ...(choose a part on the right to read more)
$3,579.44
Make a selection BES97005080S11 Brombacher panamera s & 4s "sound version" sport muffler - 10 crank hp & + 9 crank torque. - 2.5'' tubing (63,5mm) straight through design for maximum power. - 11 lb. Weight savings. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - quad 4'' (100mm) round tips sold separately for basic OEM systems (without Porsche sport exhaust)* - tips can be individually adjusted for personal taste. - deeper tonal quality and louder volume which enhances 4.8 l Porsche sound.** - no ecu (software) programming necessary. - will work with OEM exhaust components. - absolutely no drone in the cabin. - does not interfere with emissions and will not trigger the check engine light. - made in Germany...(choose a part on the right to read more)
$2,674.19
Make a selection BES98215000S The open architecture of this muffler allows for a deeper four-cylinder turbo tone, with plenty of whistling on tap. Coming off throttle from higher rpms exudes a chorus of snarling, gurgling and crackling letting everyone know that this car is not your average 982. + 15 hp & + 12 tq gain. - 2 x 3.5 (90 mm) round tips. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - lower deeper tones than the factory exhaust with far more whistling and gurgling / crackling off throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - no drone in the cabin. - "aero quip" style motorsport muffler connections t...(choose a part on the right to read more)
$3,636.47
Make a selection BES981C1200SGT4 - equal length long tube headers with motorsports merge collector. - 200 cell hd German hjs tri metal sport cats. - primary diameter 50mm outer , 47mm inner for the larger 3.8l displacement. - t316 lightweight stainless steel. - reduces thermal stress on the motor. - made in Germany by m&m exhaust gmbh. Please add 2 engine to header gaskets when ordering - 2 qty 997 111 107 31 power: - 981 GT4 / spyder (3.8l) = + 18 crank hp (13kw) & 16 crank torque ( 21 nm) our latest development for the 981 is aimed at those who are looking for more torque in the mid-range, a rich, deep exhaust growl. These headers contain the latest hjs cats, they are nicknamed "hd" for high durability matrix design catalytic converters. T...(choose a part on the right to read more)
$6,242.94
Make a selection BES987C0200SHD Brombacher Cayman/s (sound version) stainless steel exhaust system facts: - + 20 crank hp & + 19 crank torque - 200 cell high flow, tri metal German hjs sport catalysts - 2 tubing (50 mm) straight through design for max. Power - weighs 57 lbs. (25,8 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability - dual 3.5 (90mm) round tips - includes quick release clamps - made in Germany - intoxicating growl at idle, partial throttle and wide open throttle - no dme programming necessary. FVD is proud to introduce our newest line of Brombacherexhaust systems. Brombacher exhausts are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredibl...(choose a part on the right to read more)
$9,225.68
Make a selection BES99102240SHDO + 15 hp & + 14 torque - 200 cell high flow, tri metal German hjs "hd" high durability matrix sports catalysts. - can be used with FVD "brombacher" mufflers. - weighs 15.5 lbs. (7.0 kg). - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - made in Germany. - intoxicating growl at idle, partial throttle and wide open throttle. The catalytic converter cores used in this system are the most advanced in the industry. They are produced by hjs in Germany and are a 200 cpsi (cell per square inch) tri-metal design. Tri-metal cats are the freest flowing and environmentally friendly aftermarket cats produced today. Tri-metal catalytic converters are rodium, platinum and iridium coated and per...(choose a part on the right to read more)
$4,734.18
Make a selection BES99101210SHD For 2012+ 911 (991) with OEM or valved Porsche sport exhaust (pse). Facts: - equal length headers with motorsports merge collector. - 200 cell hd German hjs tri metal sport cats. - 2 3/4 tubing (70mm) - reduces thermal stress on the motor. - made in Germany power with software and bmc filters: - 991 (3.4l) = + 25 crank hp (15 kw) & + 18 crank torque (20 nm) - 991s (3,8l) = + 25 crank hp (15kw) & 18 crank torque (20 nm) our latest development for the 991 is aimed at those who are looking for more torque in the mid range, a rich, deep exhaust growl. These headers contain the latest hjs cats, they are nicknamed "hd" for high durability matrix design catalytic converters. They have a sm-matrix (winding of three f...(choose a part on the right to read more)
$5,221.26
Make a selection BES99104060S + 11 hp & + 10 tq gain. - 2 3/4 tubing (70mm). - weighs 35.2 lbs (16 kgs) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - does not interfere with emissions and will not trigger the check engine light. - includes block off plates & caps to use with either the OEM center muffler or an aftermarket center muffler bypass (with 2 inlets). - replaces the OEM valved side mufflers. Connects to OEM header and catalytic flange and connects to OEM center muffler or bypass. - can be used with bes99107060s1 for an even more aggressive growl. * please note - you will no longer have use of your valves ! Our 991 GT3 side muffler replacements are vastly different than the baffle plated mufflers stu...(choose a part on the right to read more)
$1,931.69
Make a selection BES99105040S Perfect muffler for those looking for a more aggressive exhaust note without changing the factory catalytic converters. The added benefit is you can reuse your OEM catalytic converters for emissions purposes. + 15 hp & + 12 torque - reuses OEM cats, perfect for those concerned about warranty. - open muffler design for added power. - tubing diameter is the same as the OEM system. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - 4 on a scale of 1-10 in volume (1 being stock) below 3,000 rpms, 6 on a scale of 1-10 in volume under maximum load (3 being stock). - includes cone and v band style hardware to prevent exhaust leaks. - made in Germany. - modular desi...(choose a part on the right to read more)
$3,154.14
Make a selection BES99106041S - 2 3/4 tubing (70mm). - weighs 7 lbs. (3,1 kg). - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - "quad" style tips, inner tip is 3.5" (90 mm) in diameter and outer is 3.4" (88 mm). - polished stainless steel. - made in Germany - will not fit stock mufflers! These tips only work in conjunction with our "brombacher" sport mufflers. Please note: using stock tips on our sport mufflers without these tips will cause hp loss. Once you restrict the diameter of the piping a small percentage of power is robbed. The exhaust tips are a dual 3.5"/ 3.4 round design and are double walled to dissipate heat, which means that they won't tarnish as quickly as single walled tips. There is an ...(choose a part on the right to read more)
$1,429.16
Make a selection BES99110200SK "brombacher" stainless steel exhaust system with valves for the 991 + 25 hp & + 20 tq gain. - 200 cell hjs "hd" sport catalysts. - 25 lb. Weight savings over OEM system (weighs 59 lbs. (27,0 kg), OEM weighs 84 lbs. (38kg). - 2 3/4 tubing (70mm). - 4 x 3.5 (90mm) round tips. - motorsport merge collector. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - absolutely no drone in the cabin. - "aero quip" style motorsport connections without gaskets or flanges to ensure a leak free exhaust. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - under load (moving) with valves closed: 85db* - under load (movin...(choose a part on the right to read more)
$10,833.37
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |