Vehicles
Sections
402 not categorized PORSCHE 356 C REAR LEDCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 928 1978-82 (includes uncategorized and accessory items) 964561005016HA This is a complete cabrio top made in Germany with original sonnenland material. It is as close to the original as possible and is cut and trimmed to fit perfectly. Includes a trapezoidal pvc plastic rear window with a zipper like the original. If the window gets hazy simply unzip, remove and add a new window. Sonnenland material consists of 3 layers, dyed acrylic twill weave top layer, elastomeric rubber inner layer and polyester woven base layer. It provides increased strength against abrasion, increased fade resistance and the tighter woven layers are made for modern electric tops with stronger frames, like the 911 and 964. Sonnenland high quality material was originally used by Porsche and other top German ...(choose a part on the right to read more)
$2,377.19
Make a selection BES99126090S Our exhaust products are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredible value. Our entire "brombacher" line of exhausts is manufactured by m&m exhaust, gmbh in Germany who is no stranger to Porsche racing exhausts. Each is tested comprehensively for flow rate, thermal stress, resistance to cracking, and longevity. To further ensure quality, m&m use lightweight, motorsports grade, t 316 stainless steel and motorsports grade carbon. Features: inner 3.5" (90 mm) polished stainless-steel tip with FVD logo outer 3.9" (100 mm) matte carbon surround includes clamps for complete installation fills the factory cut outs perfectly can be adjusted for r...(choose a part on the right to read more)
$925.45
Make a selection BK7032 Originally published by floyd clymer this is a faithful reproduction of the 1969 publication of that manual. By far the most comprehensive manual ever published for the 912 Porsche it includes complete technical data, service and maintenance information and comprehensive detailed instructions for the repair and overhaul of all major and minor mechanical and electrical components, making it an invaluable resource for collectors and restorers of these classic automobiles. There are separate sections that deal with the repair and overhaul procedures for the engine, ignition system, fuel system, clutch, transmission, rear suspension, steering, front suspension, brakes, heater, exhaust and emission control system pl...(choose a part on the right to read more) General FitmentACCESSORY
$43.15
Make a selection FVD205986001 Front 26mm (not adjustable) rear 22mm (2 way adjustable)
$504.90
Make a selection FVDBSK352930002 Make your next brake service a breeze with our pre-packaged service kits. Quality means everything to us, so we only source these parts directly in Germany. This kit contains: 2 qty. Rear rotors (zimmerman), part # 93035204501eq & 93035204601eq 1 qty. Oem set of rear pads (textar), part # 96435193903 sold as a set. 1 necessary per car.
$464.51
Make a selection FVD205996003 Front 25mm (3 way adjustable) rear 24mm (3 way adjustable)
$1,216.51
Make a selection FVD205996003VAG These bushings are made for h&r front sway bars with 25 mm diameters. They are a direct replacement for our part # . These will also work on any bar with a 25-mm diameter. If you would also like to replace the rear, please use part # FVD205996003hag sold as a front set. 1 set needed per car.
$62.96
Make a selection FVD205997001 Front 26,5mm (3 way adjustable) rear 24mm (3 way adjustable)
$867.24
Make a selection FVD205997003 Only for cars with pdk front 24mm - not adjustable rear 24mm - 4-way adjustable
$895.75
Make a selection FVD205997005 Only for cars with pdk front 26mm - 3-way adjustable rear 24mm - 4-way adjustable
$933.77
Make a selection FVD33104381 The tow link is the furthest rear control arm on the rear axle. It is responsible for the toe angle adjustment. The OEM control arm bushings are simply too soft for track events and the teflon monoball racing bushings are too far too hard and noisy for street cars. Our sport bushings are made of a denser rubber (85 shore opposed to OEM 65 shore), which means that they are suitable for street and track use. Equally as important is that they do not produce any noise like the teflon bushings. FVD sport control arm facts: - better handling and more responsive. - makes precision adjustments of the suspension easier. - does not produce noise. - shore a hardness value of 85 for durability and handling. - fit's like o...(choose a part on the right to read more)
$488.12
Make a selection FVD20799601 Scavenging and aeration in the oil pan have been identified as a problem in 996 and Boxster models experiencing high g-forces on the racetrack. This oil pan spacer provides a simple solution. This spacer increases sump capacity by half a liter, providing more reserve to ward off starvation. Thisoil pan spacer clears all factory options including the rear skid plate. Added oil capacities as well as increased oil pan surface area increase oil cooling and engine performance. *oil pan and sump baffle are OEM parts and do not need to be purchased material: 6061 t6 aluminum alloy finish: clear anodized weight: n/a models: Boxster, Boxster s, and 996 models (excludes GT3 and turbocharged models) installation: for best...(choose a part on the right to read more)
$306.50
Make a selection FVD33150020 This kit is complete and includes the front and rear monoball cartridges with press tools. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 4. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$772.20
Make a selection FVD33150001 Solid bushings and mounts allow you to achieve exact suspension articulation which improves handling and stability on lowered / race prepared cars. The original soft rubber bushings can deform under track loads which allows the sub frame to shift and throw the camber and toe off. Solid bushings will not deform and will keep the camber and toe settings in line which equates to confidence in cornering and faster lap times. These are intended to replace the soft rubber bushings on the original rear sub frame (part #'s 993 331 051 00 & 993 331 052 00). They are made in Germany and are TUV approved. Sold as a set. 1 set is necessary per car. Please note: if you are also driving your car on the street, they will res...(choose a part on the right to read more)
$262.55
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$236.41
Make a selection 100555111NB This is a rear carpet kit for a rs model or a rs tribute, without back seats. This set is a lightweight fine German velour that is trimmed in vinyl. Each is cut, sewn and trimmed to fit perfectly. We can also add special order script on the rear deck, just contact us and let us know what you have in mind. Made in Germany. Sold as a set. 1 necessary per car.
$773.39
Make a selection FVD33150045 Original rubber replacement bushing (65 shore hardness value) for the rear control arms (camber link and caster link). This bushing cartridge is weather sealed and is crafted in high carbon steel and 7075 t6 aircraft aluminum. Sold individually.
$70.09
Make a selection FVD33150040R Replace worn-out original rear sub frame (side panel) bushings with our FVD clubsport series. They are made of rubber with an 85 shore hardness value, that is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. This bushing is made in Germany. It is crafted in high carbon steel and 7075 t6 aircraft aluminum and includes an 85 shore hardness value core. This is a front and rear bushing for one sub frame. 2 are necessary per car. We also sell the entire right and left rear sub frames with these bushings already installed, please order our part # FVD331993001.
$463.32
Make a selection FVD333007 These high quality, German made mounts are made specifically for rear shock absorbers that contain a 15mm i.d. Uniball spherical bearing. They are located at the base of the rear shocks, and secure the shock to the rear trailing arms. They are required with FVD exclusive suspension kits with part #'s 115 900 911 xx / xxx. For example 115900911030 they are also required for rear shocks like part # FVD33315755 sold as a set. 1 necessary per car.
$188.89
Make a selection FVD33398701 Bilstein suspension featuring with upside/down technology. Lowering 35 mm front and 30 mm rear - giving it a GT3 stance.
$3,028.21
Make a selection FVD33399600B8 Bilstein suspension featuring with upside/down technology. Lowering 35 mm front and 30 mm rear - giving it a GT3 stance
$2,525.69
Make a selection FVD33396401 A cost-effective combination of bilstein b6 shocks with a set of German h&r lowering springs. This kit is a perfect balance of performance and comfort for street use. Benefits: optimum adhesion and enhanced stability for daily driving and extreme driving situations. Slightly lower stance at 1.3 inches (35 mm) front / 1.18 inches (30 mm) rear. Marked improvement in safety and sportiness. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Please note: if you would like to reduce the ride height, please order part # 115110016 which will lower the stance by another 1.5 inches (40mm).
$2,741.61
Make a selection FVD33300905 This rear spring plate is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New rs spec. (85 shore) rubber bushings are installed to make this a direct bolt on. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Features: made from ¼ inch spring steel includes new rs spec. (85 shore) rubber bushings made in Germany sold individually. 2 necessary per car.
$295.81
Make a selection FVD33399600B6 Bilstein suspension featuring with upside/down technology. Lowering 35 mm front and 30 mm rear - giving it a GT3 stance
$2,637.36
Make a selection FVD51154199 Prevents the hood from accidentally opening at speed and keeps the hood in place should an impact occur. These are genuine Porsche motorsports parts from Germany. Fits front hood / trunk and or the rear deck lid. Sold individually. All motorsport and racing parts are special order items. Special order items must be paid for in advance. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis and do not carry any warranty. No exceptions.
$99.79
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |