PORSCHE 987 RUBBER O RINGCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 928 1978-82 - Transmission (includes uncategorized and accessory items) 96433106080 Our spring plates are manufactured in europe by an OEM supplier to Porsche using the finest materials (high carbon steel, 7075 t6 aluminum and 65 shore rubber - oe spec). Sold individually. Right side fitment. 1 qty. Required.
$734.40
Make a selection 91133300900B Bushings set with instructions:w/ 55-60 shore a
$32.28
Make a selection 150TBR900 Replace worn-out original front control arm / wishbone bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This is located at the front of the control arm / wishbone. The correct matching poly-graphite bushing for the front of the control arm is part # 150tbf900 sold individually. 2 necessary per car.
$53.46
Make a selection 96434101807AT By ordering this article number, you will receive a reconditioned wishbone with newly pressed-in bearings. The calculated replacement deposit will be returned to you as soon as the old part has been received and checked. This item is also available with race bearings (85 shore).article number FVD 341 018 07at the reconditioning process includes full inspection of each track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. If your old part is not repairable we will inform y...(choose a part on the right to read more)
$462.13
Make a selection 96433105980 Our spring plates are manufactured in europe by an OEM supplier to Porsche using the finest materials (high carbon steel, 7075 t6 aluminum and 65 shore rubber - oe spec). Sold individually. Left side fitment. 1 qty. Required.
$734.40
Make a selection 150SPB965 Replace the worn-out spring plate bushing with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This is the inner bushing for the 1-piece non-adjustable spring plate. Sold individually. 2 necessary per car.
$51.08
Make a selection 150PB10134 Replace worn-out original sway bar drop link bushings with this longer lasting poly-graphite plastic bushing set. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. The set includes 4 complete bushings and 4 sleeves (8mm inner diameter). Sold as a set. 1 necessary per car.
$79.60
Make a selection 91133300900BHD Bushings set with instructions:w/ 80-85 shore a hardness
$32.28
Make a selection FVD34101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$509.65
Make a selection FVD34391101SET Replace worn-out original front lower control arm bushings to return your car to its intended suspension geometry and steering feedback. Features: better handling reduces that sloppy steering feel does not produce any noise like the teflon bushings. Rubber has the original shore hardness value of 65 (like oem) fit's like oem, simple installation made in Germany if you are looking for a sportier upgrade we suggest our sport lower control arm set, part # FVD34391192set. Set is sold per axle. 2 necessary per car.
$165.13
Make a selection FVD375003 Are you experiencing vibrations in the cabin? The most likely cause is a worn transmission mount. Severely worn mounts translate to engine component wear and can even cause difficulty shifting. Our mount is manufactured in europe by an OEM supplier using the finest materials. It is a 65 shore rubber hardness value which is the same as the what was standard on these cars. Be sure to swap yours out during your next service. Sold individually. Central fitment in transmission carrier 96437502301. 1 qty. Required. Tech tip: now is the time to replace the old hardware as well. Below is a list of what is needed for installation. 1 qty. Hex head bolt m10x100 90007429202 1 qty. Lock nut m10 49020001 2 qty. Washers 10.3x...(choose a part on the right to read more)
$178.20
Make a selection 150SPB976 Replace worn-out spring plate bushings with these longer lasting poly-graphite plastic bushings. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This includes the inner and outer bushing for the 2-piece adjustable spring plate. Sold individually. 2 necessary per car.
$42.77
Make a selection FVD375003S Are you experiencing vibrations in the cabin? The most likely cause is a worn transmission mount. Severely worn mounts translate to engine component wear and can even cause difficulty shifting. We can offer your c4 a more sporty feel without the harsh vibration from a solid mount. Our transmission mount is manufactured in europe by an OEM supplier using the finest materials (high carbon steel, 7075 t6 aluminum and 85 shore rubber - rs spec). The rs spec shore rubber offers the c4 sportier handling without being too stiff for street use. Be sure to swap yours out during the next service. Sold individually. Central fitment into the transmission carrier bracket 96437502301. 1 qty. Required. Tech tip: now is the ti...(choose a part on the right to read more)
$190.08
Make a selection FVD34391192SET Replace worn-out original front lower control arm bushings with our FVD sport bushings, made of rubber with an 85 shore hardness value that is the same as the rs models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. Features: better handling reduces that sloppy steering feel makes precision adjustments of the suspension easier does not produce any noise like the teflon bushings. Rubber has a shore hardness value of 85 (like rs models) fit's like oem, simple installation made in Germany set is sold per axle. 2 necessary per car.
$171.07
Make a selection 91163103300 This is the screw that sits at the base of the adjustment ring, part # 91163193301. We also recommend purchasing a new rubber spacer, part # 91163113900. Sold individually. Driver's and passenger's side fitment. 2 necessary per car.
From $8.64
Make a selection FVD34101707ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$451.44
Make a selection VDO240101 This is by far the most elegant and efficient solution for mounting any gauge in your Porsche. black plastic cup with metal bracket and fits one 2 1/16" gauge. Long body has plenty of room to fit any fitting out of the back of the gauge. Cup tilts in it's mount for the best viewing angle. Comes with rubber gauge ring for the perfect fit. General FitmentALL
$65.83
Make a selection FVD33391101SET These bushings are manufactured from higher density, rs specification rubber (85 shore). Rs bushings are more durable than OEM 65 shore, provide more positive suspension location and are still quiet and compliant for street use. This set is a direct replacement for original part # 911 333 009 00 sold as a set. 1 necessary per axle.
$117.61
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |