Vehicles
Sections
207 not categorized PORSCHE 356A B AND BCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 914 1970-76 (includes uncategorized and accessory items) 91435553100 Known as: ring fitting View/Change Diagram
From $27.11
Make a selection 91442424700 Avoid purchasing a costly new emergency handle with these handy repair parts. A little labor and then the brake handle that works like new. View/Change Diagram
$21.37
Make a selection 914423285W At last a bracket to hold the end of the 914 accelerator cable when converting to carburation. Easily installed in the casing, this eliminates fabricating your own.
$42.66
Make a selection 91442407305 We have all longed to install the factory look center consoles in our beloved 914s, and the console, the gauges and even the aftermarket factory look wiring harness was never a problem, it was the 90 degree bend console heater switch. made especially by the factory to clear the slot in the console, this long discontinued switch was as rare as hens teeth and to try and bend the original was a futile exercise. we now have a quality factory look reproduction to instantly solve the problem and return your 914 to the factory perfection it deserves. General Fitment914 1970-76
$45.22
Make a selection 91442425601 Superb reproduction of the outrageously expensive factory part View/Change Diagram
From $45.22
Make a selection 91450107510 Just pulled up on the 914 emergency brake handle and it broke off in your hand? The pivot stand has rusted away! Years of hardtop side seal leak directly onto this complex part has caused the problem. Discontinued by the factory in 2001 this identical part is an easy installation after simply sliding out the drivers seat and removing the seat rack and rocker carpet. This part can then be spot welded in. View/Change Diagram
$74.41
Make a selection 91442450200 View/Change Diagram
$15.66
Make a selection 91450194420C At last, a solution to right frame rail rust. The inner rocker solves the problem from the jack post to the front, but what about under the jack post to the rear? The solution is our right inner wheel house repair panel. It solves both right rear frame rot as well as the behind the battery tray rust-through. Easily welded in, it restores these areas' strength, as well as the stock appearance. One piece does it all! Piece is made extra strong and coated for good rust protection. General Fitment914 1970-76
$259.09
Make a selection 91442405500 Disengagement rod for the early 70-72 914 breakaway two piece handle. View/Change Diagram
$46.98
Make a selection
$17.17
Make a selection 91454217310S This excellent set of reproduction replaces the no longer available factory parts and is the plastic cap that fits at the rear top of the door and finishes off the squeegee. each easily installs with two screws, one of which holds the rear window guide channel. Set of left and right caps. General Fitment914 1970-76
$30.07
Make a selection 91454211110S This is a set of high quality plastic cap that nicely finishes off the squeege at the back of the side window while providing the final groove for the squeege to fit into. easily installed with one screw, they also helps keep the window from rattling. This part also fits about the first 1000 1973 914 models. sold as a set of 2, for left and right sides. General Fitment914 1970-76
$37.28
Make a selection
$48.47
Make a selection 91455204010BA This faceplate replaces the factory piece in the 1970-74 914 dashboard and accommodates blaupunkt frankfurt and becker radios. Comes upholstered, you must cut the shaft and radio holes. General Fitment914 1970-76
$33.77
Make a selection 914503125610 Finally an excellent reproduction of the outer steel factory rocker panel. Identical to the original at a fraction of the new price. Now get both side for one low price! General Fitment914 1970-76
$312.12
Make a selection 91456302113 Excellent reproduction of the original 914 hardtop front bolster that always breaks its ends off due to rough handling when releasing the top handles. made from modern automotive materials, this part should last longer than the life of your 914 and will not crack like the original. View/Change Diagram
$200.34
Make a selection
$20.61
Make a selection 91142479203
From $15.72
Make a selection 944VIC8501 Just pop off your emblem and reinstall into new unit. Remove old worn out unit, install new one. Please specify desired color and shift pattern when ordering. This part has a 2-3 week lead time. General Fitment944 1985-88944 1989-91 968 1992-95 914 1970-76
$118.26
Make a selection 915302911161 This ring and pinion is manufactured in Germany to our specifications using case hardened steel (18crnimo7-6). Our specifications include special heat treatment which is extremely wear resistant, contains a tough inner core, includes high tensile strength and exhibits lower noise levels. Sold as a set. 1 necessary per car. Technical info: setting for the drive train is on the bevel gear and not as usual on the ring gear.
$5,841.40
Make a selection
$35.59
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |