Vehicles
Sections
351 not categorized PORSCHE 914 HEAD BOLTCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 914 1970-76 (includes uncategorized and accessory items) 70476LED The h-4 hella led headlamp conversion is the best thing you can do for your lighting! bright white light illuminates much further than stock or even the typical h4 headlamps, showing you the whole roadway. These hella leds bolt directly in place of your headlamps and include the cable and relay. The ultimate. A must for us near-sighted drivers! if you have a 356 six volt system please specify and we will substitute the six volt leds order two for a complete set. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 924 1986-88 924 1980-85 924 1976-79 944 1989-91 944 1985-88 944 1982-85 928 1983-86 928 1978-82 914 1970-76 968 1992-95 ACCESSORY
$214.92
Make a selection 914352423A This is the splined adjusting lug for the inside of the rear 914 caliper. it is easily removed by cocking a long 4mm allen wrench in it. it is located under the inner adjuster cover which may have an allen socket or a 10mm bolt head to remove. extra long for an easy reach. adjusted through the swing arm, the pads need to have 8 thousands clearance between the pad and the rotor, and check the rotor for warpage. General Fitment914 1970-76
$28.62
Make a selection STP222 This 17 mm magnetic box v-wrench is needed for securing the top engine bolts from rotating during removal and reinstallation of motor from transmission. The 12 point socket has magnetic insert to hold wrench onto bolt head while the nut is being loosened. This tool is a necessity when doing a clutch replacement with the engine still in the vehicle. Applicable: Porsche models using 17 mm connecting bolts with a hex head. Please call our office for availability. General Fitment356 1950-59356 1960-65 912 1965-69 914 1970-76
$124.79
Make a selection 91134732700 Known as: hexagon-head bolt View/Change Diagram
$16.25
Make a selection 90007413402 #51 View/Change Diagram
From $3.70
Make a selection 9142510000C Our beautiful muffler gasket kits offer you everything you need for a perfect installation except a little labor! Don't fight rusted bolts or sae sized hardware. Specifically for the '75-76 2.0l. General Fitment914 1970-76
$45.06
Make a selection 91433203500 This is a all new lobro made in italy rear cv axle boot kit. Its a great idea to replace the boot and the rest of the small parts all necessary after so many years of usage. Why not get the kit ready to go with the lobro grease the washer, 'c' clip, all ready to go for a new suspension job. This is a great part compared to the yellow bottom flange color cv axle boots since these rubber boots are a better quality than the competition. Why settle for cheap aftermarket cv axle boot kit and search for a quality grease when you can buy the kit and complete the job the right way the first time. get this great lobro italian made cv rear axle boot kit today~! Fits all rear left or right axle for Porsche 914-4 '70-...(choose a part on the right to read more) View/Change Diagram
From $11.88
Make a selection N0101544 Known as: hexagon-head bolt View/Change Diagram
$3.35
Make a selection N01021513 Known as: hexagon-head bolt / hexagon-head bolt m 6 x 15 / hexagon-head bolt m 6x15 din 933-8.8 / hexagon-head bolt m 6x15 View/Change Diagram
From $1.19
Make a selection MIS200 The quick six mounting kit enables you to immediately bolt a six-cylinder engine into your 914-4, using the factory engine pods. the '73-76 bodies, however, do require the purchase of the early rubber engine mounts. The bulkhead mount is for the serious six conversion. Welded in by a competent mechanic, it allows you to eliminate the four cylinder mounting pods allowing more clearance for valve adjust, easy removal of the rear shift bar and most importantly shifts the center of weight further forward to the factory recommended position. Includes 930 engine mounts General Fitment914 1970-76
$745.20
Make a selection 90007401502 Known as: hexagon-head bolt / hexagon-head bolt m 6 x30 din 931-8.8 / hexagon-head bolt m 6x30 / hexagon-head bolt m 6 x 30 various applications great for securing the rear engine lid catch on a 914 View/Change Diagram
From $1.51
Make a selection FVD10397592 Use only when already connecting rods with sps-carr-6 was delivered! General Fitment911 1994-98911 1989-94 914 1970-76 911 1970-73
$67.54
Make a selection ST5201 The lemans is a classic, handmade, custom seat with a firm support. It comes in leatherette with basket weave. The configurations were used in the recaro sport seat and the Porsche seat and the classic choice for the classic seats. The lemans is currently our lightest seat and is used as a vintage race seat as a bolt in replacement and upgrade for the Porsche 914. Some customers have had the seat installed in the Porsche 904 replicas. Sliders, as well as matching headrests, are standard on all seats. seats sold separately as well as seat brackets for specific cars. General Fitment914 1970-76911 1970-73 911 1965-69 912 1965-69 356 1960-65 356 1950-59
$1,668.60
Make a selection 90015502602 Known as: hexagon-head bolt m 10 x 85 View/Change Diagram
$3.78
Make a selection N0103404 Known as: hexagon-head bolt / hexagon-head bolt m 8 x 40 View/Change Diagram
From $1.89
Make a selection ST5202 The lemans is a classic, handmade, custom seat with a firm support. It comes in leatherette with basket weave. The configurations were used in the recaro sport seat and the Porsche seat and the classic choice for the classic seats. The lemans is currently our lightest seat and is used as a vintage race seat as a bolt in replacement and upgrade for the Porsche 914. Some customers have had the seat installed in the Porsche 904 replicas. Sliders, as well as matching headrests, are standard on all seats. seats sold separately as well as seat brackets for specific cars. General Fitment914 1970-76911 1970-73 911 1965-69 912 1965-69 356 1960-65 356 1950-59
$1,188.00
Make a selection 90007402202 Known as: hexagon-head bolt / hexagon-head bolt m 6 x 65 View/Change Diagram
$2.14
Make a selection 90007411102 Known as: hexagon-head bolt / hexagon-head bolt m 6 x 50 View/Change Diagram
$2.52
Make a selection 90007411103 Known as: hexagon-head bolt m 6 x 50 View/Change Diagram
$1.19
Make a selection AAA25600A This kit consists of all the proper hardware to install heat exchangers and a muffler, including the rare copper locking nuts to ensure a perfect installation. Remember to install the exchangers one at a time and torque in an x pattern to 18 ft lbs. General Fitment914 1970-76
$73.88
Make a selection N0102311
View/Change Diagram
From $1.08
Make a selection 702863 If you buy the wheel adapter set you will need these special short head bolts to mount them to the car. Sold individually, you will need 12 bolts. General Fitment914 1970-76
$3.46
Make a selection 90008204302 View/Change Diagram
$15.66
Make a selection FVD10397505CARR Carrillo is one of the most respected connecting rod manufacturers in competitive motorsports. Carrillo rods are constructed from their proprietary alloy and forged to their custom specifications. The rods are then fully machined to guarantee the removal of all surface imperfections. After heat treatment, each connecting rod is magnaflux inspected and hardness checked, then machined to final size. Each set is balanced and then shot-peened to achieve the ultimate in strength and fatigue properties. The carrillo multiphase (carr) connecting rod bolt (sps-carr-6) is a high quality, aircraft standard fastener. Each bolt is manufactured with asymmetrical threads, each thread has a slightly different design than the ...(choose a part on the right to read more)
$3,188.59
Make a selection FVD1109115040 This replica high butterfly mfi throttle bodies system is for those looking for ultimate engine performance as well as an authentic rsr engine appearance. This kit keeps air consistently on tap for superior drivability. When the throttle is opened, there is an instant injection of air, providing a sharp, crisp throttle response. This efficient injection frees up more power and compliments larger displacements, high lift cams and full exhaust systems. This kit is engineered, precision machined, flow tested and manufactured in Germany. It is replicated to look as close to the original as possible. Intake trumpets (velocity stacks) are available in your choice of red or black. Includes: 6 individual stacks (50 mm ...(choose a part on the right to read more)
$8,053.45
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |