Vehicles
Sections
30 not categorized PORSCHE 944S SHEET METACan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 914 1970-76 (includes uncategorized and accessory items) 90014302902 Known as: oval-head sheetmetal screw / oval-head sheetmetal screw b 4,2 x 16 View/Change Diagram
From $1.08
Make a selection 111971911A Known as: rubber sleeve / rubber sleeve 15 $ / rubber sleeve f >>92483 30116 / grommet View/Change Diagram
From $7.67
Make a selection 914256331BO For you racers or for anyone running a type four engine and not connecting the heating system, comes this nifty way to block off the two round holes in the sheet metal where the j pipes enter to connect to the heater blower motor. easily installed using the original j pipe screw hole, these come semi gloss powder painted for a perfect match to the factory sheet metal. price is for a set of two. General Fitment914 1970-76
$31.86
Make a selection 914503125 Kit consists of: General Fitment914 1970-76
$42.22
Make a selection 021119543A This is the black protective edging that fits on the edge of the engine sheetmetal. it finishes the raw edge to prevent cuts. View/Change Diagram
$27.46
Make a selection 022129881F Throttle return spring fits between the throttle body lever and the sheetmetal on the 914 1.7 and 1.8 models. View/Change Diagram
$8.69
Make a selection 150752 As we all know the only way to install the optional oil pressure gauge is to replace the oil pressure switch with the much "fatter" oil pressure sender. this cannot be accomplished without cutting the sheet metal or extending the hole out of the sheet metal and attaching the sending unit. this hose will give you the needed length. (might need to grind down the male end for a proper fit) General Fitment914 1970-76
$41.04
Make a selection GR1019 If you are doing sheet metal repair to your Porsche (or any car, for that matter), wurth seam sealer is a must-have. It is used to seals seams & joints that are spot welded, riveted, or bolted. permanent adhesion to bare or painted surfaces. Brush able, low odor formula goes on thick to seal completely, and provides an OEM appearance when finished. Will not sag, shrink, or crack, and is paint-ready in 45 minutes. Temperature range from -13ºf to +176ºf. General FitmentACCESSORY
$63.18
Make a selection 91150403100GRV3 This is a sheet metal repair cup that is located behind the fuel door. It includes the fuel door hinge mount, lock (part # 901 504 034 20grv), buffer (part # 911 025 679 00) and tube for the pull cable. It is manufactured by dansk, they offer a complete line of replacement bodywork to complement the entire Porsche model range. All dansk products are manufactured to European standards to ensure the quality that you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Sold individually. 1 necessary per car. Please note: due to variances in production at the factory, age, accident damage or rust, each part may require trimming and or adjustment ...(choose a part on the right to read more)
$307.69
Make a selection FVD504911RSR These fender flares are made of metal sheet set (4pcs): - fender flare front left - fender flare front right - fender flare rear left - fender flare rear right
$5,834.27
Make a selection 91450415510 A must have part for engine cooling. Replace this part when the engine is out and clean the bay at the same time! This part is for the drivers and passengers side only. Check all engine sheet metal boots and seals while you are at it for the best cooling. View/Change Diagram
From $20.52
Make a selection AAA25600A This kit consists of all the proper hardware to install heat exchangers and a muffler, including the rare copper locking nuts to ensure a perfect installation. Remember to install the exchangers one at a time and torque in an x pattern to 18 ft lbs. General Fitment914 1970-76
$73.88
Make a selection AAA25600B This kit consists of all the proper hardware to install heat exchangers and a muffler, including the rare copper locking nuts to ensure a perfect installation. Remember to install the exchangers one at a time and torque in an x pattern to 18 ft lbs. General Fitment914 1970-76
$79.52
Make a selection N0141412 Known as: oval-head sheetmetal screw View/Change Diagram
$1.35
Make a selection
$1.19
Make a selection F916 Our five piece set of 914-6 sheet metal exactly duplicates the real thing as well as providing the unavailable right rear section. When installed, it enables your six cylinder engine to perfectly fit the engine bay. Painted in black.
$437.25
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |