Vehicles
Sections
140 not categorized PORSCHE 996 WIL VICan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 912 1965-69 (includes uncategorized and accessory items) 90134101890 Rennline high density front strut mounts for your 911/914 not only replace tired factory rubber pieces, but return better handling and ride quality without being overly stiff. At 25% more stiff than stock, these are a great compromise, allowing the front suspension to maintain better alignment and geometry over bumps and around corners thanks to their increased stiffness. Still at home on a race track, these will ride with a feel closer to factory than that of our more track oriented full camber plate and monoball setups. General Fitment914 1970-76911 1965-69 912 1965-69 911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73
$267.30
Make a selection 96414718703EQ Remove the power steering belt cover to inspect your toothed steering belt for wear and cracking. Belts undergo a lot of friction and wear, so replacing them periodically will prevent damage. Be sure to follow recommended service and replacement intervals set by Porsche on belts or examine the power steering pump belt at each oil change. Sold individually. 1 necessary per car.
$73.66
Make a selection 96433102200RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$725.87
Make a selection 96434101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for...(choose a part on the right to read more)
$462.13
Make a selection 96434307281ATK Looking for a more cost-effective solution than ordering a new link? Let us recondition your original drop link. The reconditioning process includes full inspection, disassembly, degreasing and media blasting. Once fully prepared, we properly install new bushings, finish with a corrosion proof coating and include a new lock nut. Please note: each link is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your link we will notify you as soon as we can. Arrangements can be made for its return to you. Sold individually. 1 necessary per car.
$210.28
Make a selection 93034702501 This item will ship when available if add to your order View/Change Diagram
From $192.24
Make a selection 911641301CXFVD Remanufactured part sourced in Germany. Includes a new rubber sealing ring. Purchase a newly remanufactured unit from us and an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and resell-able, the core deposit will be refunded. Sold individually. 1 necessary per car. Please note: this is a special-order item. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis. Please call us in advance of placing your order, these are very hard to come by and in some instances, we c...(choose a part on the right to read more)
$1,120.28
Make a selection 91436131501S By far the best way you can fit mahle pedrini or fuchs factory alloy wheels on your 914 inexpensive 17mm head 40 mm shank, this set replaces the impossible to find factory originals. The alloys on a 914 need super long threads so without this special bolt the wheels will not hold on.
$129.06
Make a selection 93034702000KIT Will ship when available.
$305.91
Make a selection 914301GT For 7” and 9” flares.
$270.00
Make a selection 91434783100
View/Change Diagram
From $14.58
Make a selection 91163125902 Drain tubes can become clogged and will eventually lead to corrosion of the head light bucket. If you are upgrading your headlights or servicing them it is a great idea to change the drain tube. Sold individually. 2 necessary per car. View/Change Diagram
From $1.73
Make a selection 90135501200 The master cylinder is a critical component of your braking system. If it begins to fail you will experience a softer, spongier pedal feel. You can also experience a pedal that slowly sinks towards the floor when it is depressed. If you check your brake fluid and notice it is dark brown or black, odds are the cylinder seals have deteriorated and the fluid has been contaminated. High-quality OEM (original equipment manufacturer) master cylinder replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. This master cylinder includes, new washers, grommets and protection cap. Sold individually. 1 necessary per car. View/Change Diagram
From $401.54
Make a selection 95037003 Stoptech brake lines consist of a ptfe (commonly referred to as teflon) inner line that carries the brake fluid, which is then covered with a layer of stainless steel woven braid. The ptfe tube is very resistant to expansion under pressure and will not degrade from exposure to brake fluid. every stoptech brake line is 100% tested in-house to a pressure of 4,500 psi. This is almost 4 times the typical line pressure exerted by a production vehicle's master cylinder. stoptech is a registered brake line manufacturer with the united states DOT and all stoptech stainless steel brake lines are manufactured to meet DOT compliance standards. Stoptech stainless steel lines also meet or exceed fmvss 106 and applicable...(choose a part on the right to read more) General Fitment911 1965-69911 1970-73 911 1974-77 911 1978-83 911 1984-86 912 1965-69
$98.93
Make a selection 90135199800 Does your car pull to one side when you hit the brakes or let go of the wheel? Do you notice one wheel seems to "get hot"? Are your calipers leaking or stuck even though you have cracked the bleeder nipples? You may need to rebuild your caliper(s). These factory kits include seals, piston clips, and boots; and with a little labor and paint, will look new as well. Reasonably priced, they sure beat the price of a new caliper! View/Change Diagram
From $30.89
Make a selection 90135293910 This is a great new part to get to finish that brake restoration project. Why settle for used caliper bridge pipe when you can still purchase a new one today. Always get new brake lines for your calipers after so many great years of use, and avoiding further costly damage. This is the rear brake caliper bridge pipe on your calipers for all Porsche 356c, 911 ' 65 - ' 69, 912 ' 65 - ' 69, fits either left or right you will need to purchase 2 to complete the job right. View/Change Diagram
From $27.00
Make a selection
$128.52
Make a selection 930602015AX3ATK Send us your distributor and we will remanufacture it for you. A perfect option for those who have time and want to save on costs. The remanufacturing process includes full inspection, disassembly, cleaning and degreasing. We then install a toothed timing belt, 3 German made top bearings, 1 German made lower bearing and a distributor pinion pin (part # 930 602 922 00). Clearances, timing and proper operation are then checked to ensure reliability. Please note: each distributor is remanufactured in Germany, so the lead times can vary.
$1,552.92
Make a selection 93061221102 When your pads reach a critical level, these sensors will trigger a warning to alert you that your pads need to be changed. Be sure to purchase these in conjunction with your new brake pads. High-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per axle.
From $14.06
Make a selection 93060610500ATK The remanufacturing process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, clean, degrease and rebuild to factory specifications. Remanufacturing is done in Germany, so the lead times can vary. Send us your original warmup regulator and we will have it remanufactured for you. We do not offer a core exchange on this part. Please note: please package your part as carefully as possible to ensure that damage is not caused en route to us.
$804.28
Make a selection
From $42.65
Make a selection
From $114.48
Make a selection
From $114.48
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |