PORSCHE 996 TURBO ECSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 912 1965-69 - Brakes/Wheels (includes uncategorized and accessory items) 99312301452ATK Our k-16 remanufactured turbo is cost competitive and is a direct replacement. Simply send us your original k16 turbochargers and a borg warner / kkk certified technician will remanufacture your turbo. The remanufacturing process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will replace the turbine wheels, thrust bearings, install new seals, recondition the internals and high speed balance the turbo. This ensures reliability and superior performance for many years to come. The remanufacturing is done on an exchange basis only. You must send us your original k16 turbocharger. After receiving y...(choose a part on the right to read more)
$2,370.06
Make a selection 99312301352ATK Our k-16 remanufactured turbo is cost competitive and is a direct replacement. Simply send us your original k16 turbochargers and a borg warner / kkk certified technician will remanufacture your turbo. The remanufacturing process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will replace the turbine wheels, thrust bearings, install new seals, install new waste gates, recondition the internals and high speed balance the turbo. This ensures reliability and superior performance for many years to come. The remanufacturing is done on an exchange basis only. You must send us your original k16 turboc...(choose a part on the right to read more)
$2,370.06
Make a selection 992CAT With over 25+ years of Porsche air and water-cooled experience, fabspeed motorsport usa offers a great enhancement for your stock exhaust or aftermarket exhaust on your Porsche 992 Carrera. Using only the highest quality helical valves imported directly from the u.k., our system eliminates any risk of failing exhaust valves. Helical limited in great britain supplies the world's very best exhaust valves to Porsche, ferrari, lamborghini, mclaren, aston martin, and other hypercar manufacturers. Other cheap aftermarket exhaust valves are not able to handle the heat produced by a rear or mid-engine car and are guaranteed to fail, break and rattle. Helical u.k. Imported exhaust valves are bullet-proof and never fai...(choose a part on the right to read more)
$5,665.63
Make a selection 93033229700EQ High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 4 necessary per car (2 per axle). Please note: this only fits 930 turbo models with the 4 speed transmission # 930.34/36 and the 1984 911 wide body models with the 5 speed transmission # 915.69 and 915.70.
$5.94
Make a selection BES95B05040SK + 15 hp & + 18 tq gain. - 2.5 tubing (63.5mm). - 4 x 4 (101mm) round tips. - 8.5 lb. Weight savings over OEM mufflers. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - electronic valve controller must be removed from the OEM unit and added to our muffler. - made in Germany. Please note: this muffler is a direct replacement the macan turbo (95b) model which comes with a single electronic exhaust valve on the passenger side. This is the very 1st aftermarket muffler for the macan 95b turbo that includes a valve like the factory system. This allows our system ...(choose a part on the right to read more)
$4,907.63
Make a selection FVD351997GT2CS2 This kit convert's the 997 turbo GT2's / 997gt3 rs pccb rotors to 997 GT3 cup car steel rotors with green cup car pads ( for cars with central lock only ) this system is complete with everything that you need to install. Do not ruin your expensive ceramic brake discs on the track. Get ready for racing with the original and much cheaper Porsche motorsport steel brake discs! What's in the box: 4 x 2-piece brake discs (380 x 34 mm - front / 350 x 28 mm - rear) 4 x wear sensors 8 x cup brake pads (racing green) 8 x screws for brake caliper 8 x damping plates technical tip: also order stainless steel brake lines (FVD b96 355 97) and racebrake fluid (012 145 ca).
$7,894.26
Make a selection 93010700607 This part number is the latest supersession from the manufacturer. For example: the turbo oil tank was originally 930 107 006 00, then 03, 04 and now finally is 930 107 006 07.
From $1,142.86
Make a selection 150PB00619 Replace worn-out original stabilizer bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. Sold individually. 2 necessary per car. Please note: this fits 911 models from 1965-73 if fitted with 19 mm original stabilizer bars. It also fits the 1975-77 930 turbo model if fitted with 19 mm original stabilizer bars.
$61.78
Make a selection BBI9911070001 The bbi autosport intercooler kit is a direct replacement upgrade for the Porsche 991 turbo. Designed with 3d modeling & computational fluid dynamics software, this bespoke intercooler features 3d printed and cfd tested end tanks, and offset cores for optimum flow and improved performance. The advanced 3d printing manufacturing process allows complex design and shapes to be produced for optimum flow. This kit is ready for installation (plug & play), using the stock plumbing and shrouds. When engineering, technology, and the right people are fueled by passion, the results are impressive.
$4,746.60
Make a selection 930123002X This remanufactured turbo is a direct replacement for original part # 930 123 002 00. The remanufacturing is completed in Germany by kkk/borg warner certified technicians. This ensures reliability, superior performance and cost effectiveness. The remanufacturing process includes: complete disassembly. All parts are cleaned, inspected and measured for tolerances. Turbine wheels are replaced. Thrust bearings are replaced. All new seals are installed. Internals are reconditioned. Parts are balanced (static & dynamic) according to balancing protocol. For a complete installation we recommend adding a gasket, part # 93012319105 an intake sleeve, part # 93011015801 and be sure to have a few spare studs on hand, part #...(choose a part on the right to read more)
From $3,220.28
Make a selection BBI9964010006 Finally, a solution that allows you to safely increase without the risk of damaging your front axles. as you add GT3 shims to your front Porsche 996/997 turbo lower control arms, you move the cv joints beyond their safe range of motion, risking failure and expensive damage. These 10mm thick precision spacers, used with 16mm of lca shims will provide an additional -1.7 deg. Of camber, while maintaining the factory cv joint and axle relationship. the spacer design features a concentric lip that positively and accurately locates it to the cv joint for perfect balance and no vibration. Each kit includes two spacers and all the needed hardware in high class 10.9 grad
$405.00
Make a selection 99704400006 Smooth-fitting indoor car cover featuring full-color Porsche logo. Designed for use out of the weather, as indoor protection from dust and dirt. Made from a breathable, antistatic material, features full-color Porsche logo. General FitmentACCESSORY
$518.41
Make a selection 21011196538 This sport muffler is engineered for the discerning Porsche 965 turbo owner who is interested in pure unbridled power and sound. It is hand made from t 321 grade stainless steel. All piping is mandrel bent for reduced backpressure and increased performance. The sport muffler exudes a lower, deeper linear-firing-order dominated flat 6 Porsche turbo sound with added turbo whistle. Exhaust tips are 76 mm (3 inch) polished ovals with a rolled lip. Each kit includes complete installation hardware, wastegate pipe and clamps. Features: gains of up to 10 hp more* t 321 stainless steel mandrel bent new wastegate pipe new gaskets new hardware new muffler clamps *dependent upon boost level and other modifications. Sold in...(choose a part on the right to read more)
$2,297.61
Make a selection FSPOR992SC Purchase disclaimer: fabspeed motorsport does not condone the use of emission defeat devices for any vehicles used on public streets or roadways. Fabspeed motorsport will not tamper, remove, disable, or bypass emissions equipment on a motor vehicle in accordance with 40 cfr section 86.1854.12(a)(3), clean air act 40 cfr 1068.101(b). This includes software, known as tunes, that reprogram a motor vehicles electronic control module to alter engine performance and enable the removal of filters, catalysts, and other critical emissions controls.
$3,991.63
Make a selection BES99715040S2 Quiet version with catalytic bypass and 4x80mm end tips these versions of FVD sport exhaust system is specifically made for increased performance vehicles. Designed for tolerable, pleasant and sonorous sound (especially for the turbo cabriolet). The elimination of the catalysts reduced drastically the back pressure and increases the performance and throttle response to the max! - stainless steel exhaust system - catalytic bypass - 4x80mm end tips - 2 3/4 tubing (70mm) straight through design for maximum power - weighs 39 lbs. (18,1 kg) - made in Germany - dme programming necessary (catalytic adaption) - stock tips will fit. Tech tip: order also repair / gasket set FVD mk9 970 02
$3,162.46
Make a selection F9664120201TTS Only for the turbo s model !
$533.41
Make a selection BK83760293 This comprehensive book is dedicated to the revolutionary Porsche 911s built between 1989 and 1994, known to aficionados and factory insiders as auftragsnummer 964 (project number 964). Porsche 911 enthusiast's companion™ covers Carrera 2, Carrera 4, and turbo models from 1989 to 1994. Whether you're a 964 owner, a prospective buyer, or a Porsche workshop technician looking for 964 information, this is an invaluable addition to your technical library. General FitmentACCESSORY911 1989-94
$91.80
Make a selection BES99125010SK Are you one of those that are looking for more sound from your Porsche sport exhaust (pse)? Perhaps it's not quite as aggressive as you would like, or your last Porsche just sounded so much better? Don't worry, we have you covered, and the beauty is, you don't have to touch the catalytic converters which is a big no, no with Porsche dealers. With the valves open you receive a far more exotic, rich, deep, turbo motorsport tone and with the valves closed, soft subtle, completely stock sounds. So, absolutely no compromise and you will be thinking, the car really should have left the factory like this! Features: - + 10 crank hp & + 8 crank torque. - weighs 29 lbs. (13 kg) - German v2a - x5crni18-10 - 1.4301 stai...(choose a part on the right to read more)
$5,218.88
Make a selection FVD123001 If you are experiencing over boost, odds are your wastegate diaphragm is torn or leaking. We are finding more and more failures on these diaphragms with our classics. We strongly recommend replacing them with the addition of an upgraded boost spring, part # FVD123110 . We also recommend replacing the pressure switch, part # 93060610100 high quality, German made, turbocharger wastegate diaphragm membrane. Sold individually. 1 necessary per car.
$143.75
Make a selection FVD10397501CARR Connecting rod with plc carr-6 screw. The s connecting screw (plc carr-6) needs only every third time to be changed under race conditions or motor sport use when overhauling the engine. When used in 997.1turbo connecting rod bearing 99310314715set must be used (tongue / nose opposite). Carrillo is one of the most respected connecting rod manufacturers in competitive motor sports. Carrillo rods are constructed from their propriety alloy and forged to their custom specifications. The rods are then fully machined to guarantee the removal of all surface imperfections. After heat treatment, each connecting rod is magnaflux inspected and hardness checked, then machined to final size. Each set is balanced and then sho...(choose a part on the right to read more)
$3,188.59
Make a selection FSPOR992TVLV Treat your 992 turbo to the finest cat-back exhaust solution on the market. This valveed exhaust system is plug-and-play with the factory pse system so you can turn pse off for quiet highway cruising and turn pse on for ripping twin turbo sports car sound!
$5,665.63
Make a selection FVD123047 FVD Brombacher997.2 tt "700 series" upgraded turbos facts: - modified compressor housing for the 3.8 l displacement - modified & lightened billet compressor wheel with 12 blades - 49.55 mm inducer - 68 mm exducer - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already running FVD software we start by re-profiling the OEM vtg turbocharger compressor housing and modifying the compressor backing plate. This is done to replace the factory compressor wheel with a larger 12 blade, modified compressor wheel. The larger wheel is also lightened allows the turbo to flow a larger volume of air (more power), and aids i...(choose a part on the right to read more)
$6,926.04
Make a selection FVD123048 FVD Brombacher997.2 tt "700 series" upgraded turbos facts: - modified compressor housing for the 3.8 l displacement - modified & lightened billet compressor wheel with 12 blades - 49.55 mm inducer - 68 mm exducer - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already running FVD software we start by re-profiling the OEM vtg turbocharger compressor housing and modifying the compressor backing plate. This is done to replace the factory compressor wheel with a larger 12 blade, modified compressor wheel. The larger wheel is also lightened allows the turbo to flow a larger volume of air (more power), and aids i...(choose a part on the right to read more)
$6,926.04
Make a selection FVD123020ATK Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)
$2,206.12
Make a selection FVD123013ATK K-16/24 turbo (up to 555 hp) power is focused on low and mid range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD brombachers 993 k-16/24 remanufactured turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The remanufacturing process starts with re-profiling the OEM turbochar...(choose a part on the right to read more)
$3,214.73
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |