![](https://30ed524141d0cac60ab4-d2e2d18a14257de3b9ce428cf077ee97.ssl.cf2.rackcdn.com/acban.jpg)
Vehicles
Sections
208 not categorized PORSCHE 924 S EFFCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 TURBO/GT2 2001-05 - Electrical (includes uncategorized and accessory items) ![]() 90110511511EQ High-quality, cost effective OEM replacement for original part # 901 105 115 03. This cover is designed and manufactured to perform like the original. Please note: this cover does not have the Porsche logo stamped on it like the genuine part. If that is a concern for your build or restoration, please order 901 105 115 11 this will require 6 qty. Washers 90003101430 and 6 qty. Self-locking hex nuts 90008400403 sold individually. 2 necessary per car.
$109.73
Make a selection 99919233850EQ Belts undergo a lot of friction and wear. They are cost effective to change and will keep your alternator and engine in good condition. Be sure to follow recommended service and replacement intervals set by Porsche on belts. Please note: specific model fitment information below. Sold individually. 1 necessary per car.
$15.02
Make a selection 99919235250EQ Belts undergo a lot of friction and wear. They are cost effective to change and will keep your engine and accessories in good condition. Be sure to follow recommended service and replacement intervals set by Porsche on belts. Please note: specifically fits 964 c2 / c4 and rs up to 1992 with the corresponding m64.01/02/03 engine codes. Sold individually. 1 necessary per car.
$25.41
Make a selection 99660610599 If you are noticing engine vibrations, misfires and even backfiring your crankshaft position sensor maybe bad. Your car's dme (ecu) uses the signal from the crankshaft position sensor to control ignition timing and fuel injection, so if your sensor is failing your engine is suffering from poor timing and is not running efficiently. This kit is complete and ready to install.
$139.41
Make a selection FVD33396401 A cost-effective combination of bilstein b6 shocks with a set of German h&r lowering springs. This kit is a perfect balance of performance and comfort for street use. Benefits: optimum adhesion and enhanced stability for daily driving and extreme driving situations. Slightly lower stance at 1.3 inches (35 mm) front / 1.18 inches (30 mm) rear. Marked improvement in safety and sportiness. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Please note: if you would like to reduce the ride height, please order part # 115110016 which will lower the stance by another 1.5 inches (40mm).
$2,665.62
Make a selection FVD123048 FVD Brombacher997.2 tt "700 series" upgraded turbos facts: - modified compressor housing for the 3.8 l displacement - modified & lightened billet compressor wheel with 12 blades - 49.55 mm inducer - 68 mm exducer - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already running FVD software we start by re-profiling the OEM vtg turbocharger compressor housing and modifying the compressor backing plate. This is done to replace the factory compressor wheel with a larger 12 blade, modified compressor wheel. The larger wheel is also lightened allows the turbo to flow a larger volume of air (more power), and aids i...(choose a part on the right to read more)
$6,733.65
Make a selection FVD33150040 Replace worn-out original rear sub frame (side panel) bushings and return your car to its original ride quality with this cost effective alternative. This bushing is made in Germany. It is crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value core. This is a front and rear bushing for one sub frame. 2 are necessary per car. If you are looking for a sportier upgrade we suggest our clubsport sub frame bushing set, part # FVD33150040r. We also sell complete sub frames with the bushings installed, part # FVD331993001.
$438.90
Make a selection FVD20730001 Have the oil thermostat threads come off with the oil line? Instead of replacing the entire thermostat, screw on our adapter to the remaining threads on the thermostat and reattach the oil line to the adapter. Simple, quick and cost effective fix to a common problem.
$46.98
Make a selection FVD123013ATK K-16/24 turbo (up to 555 hp) power is focused on low and mid range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD brombachers 993 k-16/24 remanufactured turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The remanufacturing process starts with re-profiling the OEM turbochar...(choose a part on the right to read more)
$3,125.43
Make a selection FVD10699601 For 986 (Boxster) and 996 modell. Fits left and right side. - specially designed for tuned and motorsport vehicles the racing & high performance division of csf build and engineer the most advanced, efficient, and reliable cooling systems in the world. Csf manufacturers radiators with high performance all-aluminum and direct-fit replacement for racecars. The only high performance manufacture to feature this advanced technology. These radiators are stamped to the same geometry of the application's original plastic end radiators. These tanks feature less welding, and are generally considered the strongest tank designs in the industry.
$576.35
Make a selection BK147147 The illustrated buyer’s guide Porsche provides enthusiasts with information and insight helpful to identifying desirable models and avoiding problems as they search for their ideal Porsche. Adding new material and revising previous information, this book covers all the Porsche models through 2010, including the last of the air-cooled 911s, the water-cooled 911s, Cayenne, Cayman, Boxster, and panamera. By dean batchelor and randy leffingwell. Paperback, 240 page General FitmentACCESSORY
$26.20
Make a selection BES99105040S Perfect muffler for those looking for a more aggressive exhaust note without changing the factory catalytic converters. The added benefit is you can reuse your OEM catalytic converters for emissions purposes. + 15 hp & + 12 torque - reuses OEM cats, perfect for those concerned about warranty. - open muffler design for added power. - tubing diameter is the same as the OEM system. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - 4 on a scale of 1-10 in volume (1 being stock) below 3,000 rpms, 6 on a scale of 1-10 in volume under maximum load (3 being stock). - includes cone and v band style hardware to prevent exhaust leaks. - made in Germany. - modular desi...(choose a part on the right to read more)
$3,066.53
Make a selection FVD10397599 Cp-carrillo's fastener assembly lube is molybdenum based lubrication grease with enhanced properties. This product offers an improved clamp load repeatability, greater resistance to high pressure and temperature (range -22f to 1200f), and no oil contamination. The coefficient of friction stays unchanged, even after several connecting rod bolt re-tightening and loosening processes. We highly recommend lubricating the connecting rod bolt head and thread with this lubricant. Be sure to add it to your order if you are replacing your rod bolts. Sold individually.
$17.33
Make a selection BES99722240BES Brombacher 997.2 tt "sport " stainless steel, sport cat converter replacements for our bes- muffler facts: - + 21 crank hp & + 18 crank torque** - 200 cell "hd", tri metal German hjs sport catalysts - tubing diameter is the same as the OEM system. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - reduces backpressure and thermal stress - 5 on a scale of 1-10 in volume (1 being stock). - reuses OEM v band style connecting hardware. - made in Germany. - available in 100 cell and cat bypass. Please ask your sales person for pricing. - more distinguished growl at idle, partial throttle and wide open throttle. - dme programming not necessary. - reuses OEM ti...(choose a part on the right to read more)
$4,518.36
Make a selection FVD33396411 A cost effective FVD exclusive combination of bilstein clubsport shocks with a set of eibach pro kit springs. This suspension kit is meant for those who want the car to sit at the lowest possible ride height. This set up will allow you to lower the front axle by 2.4 inches (60 mm). This is a perfect kit for clubsport or race use where the surfaces are smooth and even. The stock rs ride height was 1.6 inches (40 mm) lower. So, this is a full 3/4 of an inch (20 mm) lower on the front axle. Sold as a complete kit. 1 kit is necessary per car. Please note: we recommend the b6 / ohlins suspension kits for those looking for more comfort for street use.
$2,746.97
Make a selection FVD123014 K-16/24 turbo (up to 555 hp) power is focused on low and mid-range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD Brombacher993 k-16/24 new turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The process starts with re-profiling the OEM turbocharger compressor housing and m...(choose a part on the right to read more)
$3,125.43
Make a selection FVD123019ATK Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)
$2,144.84
Make a selection FVD123025ATK K24/26 exchange turbo (only OEM k24 exchange accepted) (up to 700 hp) power is focused on mid and top range rpm's. Facts: - modified compressor housing and backing plate - modified & lightened high flow compressor wheels. - remanufactured by kkk / borg warner certified technicians - free software update for those already running FVD software. FVD brombachers 996 k24/26 race turbos are new units created for those who are looking for ultimate in performance. Power is focused in the mid and top rpm range while keeping turbo lag low. They are completely bolt on and do not require custom headers or special modifications. The factory OEM turbocharger compressor housing is re-profiled and the compressor backing plate...(choose a part on the right to read more)
$3,125.43
Make a selection FVD123047 FVD Brombacher997.2 tt "700 series" upgraded turbos facts: - modified compressor housing for the 3.8 l displacement - modified & lightened billet compressor wheel with 12 blades - 49.55 mm inducer - 68 mm exducer - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already running FVD software we start by re-profiling the OEM vtg turbocharger compressor housing and modifying the compressor backing plate. This is done to replace the factory compressor wheel with a larger 12 blade, modified compressor wheel. The larger wheel is also lightened allows the turbo to flow a larger volume of air (more power), and aids i...(choose a part on the right to read more)
$6,733.65
Make a selection FVD123048ATK FVD Brombacher997.2 tt "700 series" upgraded turbos facts: - modified compressor housing for the 3.8 l displacement - modified & lightened billet compressor wheel with 12 blades - 49.55 mm inducer - 68 mm exducer - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already running FVD software we start by re-profiling the OEM vtg turbocharger compressor housing and modifying the compressor backing plate. This is done to replace the factory compressor wheel with a larger 12 blade, modified compressor wheel. The larger wheel is also lightened allows the turbo to flow a larger volume of air (more power), and aids i...(choose a part on the right to read more)
$2,766.23
Make a selection FVD50399101MM The moshammer front fender set blends just the right amount of motorsport pedigree with functionality. This aggressive design is captivating on any 991 model and offers a level of exclusivity not found with competitors body kits. The integrated fender vents lower the thermal load on the brakes by allowing the heat to be quickly ventilated up and out of the wheel arch. This composite fender set has been meticulously designed to bolt up to the factory locations for perfect panel fitment, alignment and consistent gaps. A perfect addition for a leased vehicle or for those looking to return the car to its original appearance in the future. These fenders complement the entire moshammer stormforce (991.1) / stormforce...(choose a part on the right to read more)
$3,812.66
Make a selection FVD351425426EQ A quality, cost effective set of replacement "big red" style calipers. These are a direct replacement for the 965 turbo, 993 c4s / rs and 993 turbo but can be installed on many 964 / 993 models with the correct caliper adapters. Please contact your FVD parts specialist for fitment questions. We also recommend swapping out your brake lines for a set of stainless braided lines when replacing calipers. Also a now is the time to install a set of our speed bleeders, part # FVD910102. They are comparable to part numbers 993 351 425 10 and 993 351 426 10. Please note: these are aftermarket calipers and do not come with the logo or brake pads. Sold individually. 1 necessary per car.
$918.23
Make a selection FVD3419991 This is a cost effective alternative to buying new control arms. Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with new bushings of the same rubber (65 shore hardness value). This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$130.52
Make a selection FVD33396500 A cost-effective combination of bilstein b6 shocks with a set of German h&r lowering springs. This kit is a perfect balance of performance and comfort for street use. Benefits: optimum adhesion and enhanced stability for daily driving and extreme driving situations. Lower stance at 1.3 inches (35 mm) front / 1.18 inches (30 mm) rear. Marked improvement in safety and sportiness. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Please note: if you would like to reduce the ride height, please order part # 115110016 which will lower the stance by another 1.5 inches (40mm).
$2,867.49
Make a selection FVD123047ATK FVD Brombacher997.2 tt "700 series" upgraded turbos facts: - modified compressor housing for the 3.8 l displacement - modified & lightened billet compressor wheel with 12 blades - 49.55 mm inducer - 68 mm exducer - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already running FVD software we start by re-profiling the OEM vtg turbocharger compressor housing and modifying the compressor backing plate. This is done to replace the factory compressor wheel with a larger 12 blade, modified compressor wheel. The larger wheel is also lightened allows the turbo to flow a larger volume of air (more power), and aids i...(choose a part on the right to read more)
$2,766.23
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |