176 not categorized PORSCHE 996 REAR ENDCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 TURBO/GT2 2001-05 - Body (includes uncategorized and accessory items) 10050330000 This 9 inch front and 11 inch rear steel fender flare set is made in Germany, we offer a complete line of replacement bodywork to complement the entire Porsche model range. Sold individually. 1 necessary per car. Please note: for conversions, these flares will allow you to run 9 wide tires in the front and 11 wide in the rear. For the 964 / 965 models the torsion bar cut out must be filled. Due to variances in production at the factory, age, accident damage or rust, each part may require trimming and or adjustment for perfect fitment.
$1,780.81
Make a selection FVD911503185186 This seal kit consists of original part # 911 503 185 00 (left) and 911 503 186 00 (right). The set can be used on the trailing edge of the front fender at the cowl just below the windshield. It is also used under the back of the rear quarter panel where it meets the bumper side panel. Genuine part sourced from Porsche ag in Germany to ensure quality, reliability and precise fitment. Sold as a set. 1 set is necessary for front fenders and one set is necessary for the rear. Please note: this is the thinner width. This is not the thicker width from the SC models.
$16.12
Make a selection 96433102100RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$725.87
Make a selection 96433102200RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$725.87
Make a selection 1153332541 Fur alle 996 und 997gt3 und cup modelle, nicht einstellbarer einrohr gasdruck renndampfer mit bilstein enwickelt u.a. Fur teilnehmer des Porsche sportscups
$1,321.06
Make a selection 99911342641EQ High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
$33.26
Make a selection FVD512996053R02 Ware ist ohne befestigung, locher mussen selber gebohrt werden. Keine 1. Klassige oberflache, mussen nochmal lackiert werden.
$1,745.14
Make a selection FVD504911RSR These fender flares are made of metal sheet set (4pcs): - fender flare front left - fender flare front right - fender flare rear left - fender flare rear right
$5,834.27
Make a selection
$415.80
Make a selection
$415.80
Make a selection
$20.83
Make a selection
$20.83
Make a selection 846R1035 This harness mount was developed in response to customer requests for a truss-style harness mount for the Porsche 996 coupe. The new 846 r1035 features water-jet machined aluminum construction much like our 846 r1025 harness truss. Like all brey-krause harness mounts, the 846 r1035 uses only existing mounting points. No drilling, welding or fabrication is required for installation. Once installed, the main portion can be unbolted in ten minutes, allowing use of the rear seats. General Fitment911 GT3 2007-11911 TURBO/GT2 2007-09 911 2005-08 911 GT3 2003-05 911 TURBO/GT2 2001-05 911 1998-05
$1,099.01
Make a selection 846R10351 This harness mount was developed in response to customer requests for a truss-style harness mount for the Porsche 996 coupe. The new 846 r1035 features water-jet machined aluminum construction much like our 846 r1025 harness truss. Like all brey-krause harness mounts, the 846 r1035 uses only existing mounting points. No drilling, welding or fabrication is required for installation. Once installed, the main portion can be unbolted in ten minutes, allowing use of the rear seats. General Fitment911 GT3 2007-11911 TURBO/GT2 2007-09 911 2005-08 911 GT3 2003-05 911 TURBO/GT2 2001-05 911 1998-05
$1,769.53
Make a selection 846R1030 The harness mount bar has been tested and certified by an independent lab to handle the types of forces required by the national highway traffic safety admin. Dot and sae j385 rev. Mar 95, motor vehicle seat belt anchorages-performance requirements. General Fitment911 GT3 2007-11911 TURBO/GT2 2007-09 911 2009-12 911 2005-08 911 GT3 2003-05 911 TURBO/GT2 2001-05 911 1998-05
$767.02
Make a selection FVD33300909ATK This non-adjustable rear spring plate is remanufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New rs spec. (85 shore) rubber bushings are installed to make this a direct bolt on. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Features: includes new rs spec. (85 shore) rubber bushings made in Germany sold individually. 2 necessary per car. This part is a remanufactured part. Send us your original and we will have it remanufactured for you. We do not offer a core exchange on this part. Each is remanufactured in Germany, so the lead times can vary.
$369.47
Make a selection FVD33150005 Restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm cannot compensate enough when lowering your Porsche, leaving you with as much as ½ inch of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration. Sold in pairs. 1 necessary per car.
$825.66
Make a selection FVD33150001 Solid bushings and mounts allow you to achieve exact suspension articulation which improves handling and stability on lowered / race prepared cars. The original soft rubber bushings can deform under track loads which allows the sub frame to shift and throw the camber and toe off. Solid bushings will not deform and will keep the camber and toe settings in line which equates to confidence in cornering and faster lap times. These are intended to replace the soft rubber bushings on the original rear sub frame (part #'s 993 331 051 00 & 993 331 052 00). They are made in Germany and are TUV approved. Sold as a set. 1 set is necessary per car. Please note: if you are also driving your car on the street, they will res...(choose a part on the right to read more)
$262.55
Make a selection FVD35161107 Wheel spacers make your tires and wheels appear wider by moving the wheel out from the hub, providing both performance and appearance improvements. Whether you want improved handling, increased safety, or simply desire your car to make a statement about your individual style, wheel spacers can help you accomplish your goal. This spacer fits between the wheel and hub. Size: 7 mm (.275 inches) bolt pattern: 5/130 center bore: 71.6 bolt / stud: n/a thread type: 14x1.5 material: strength tested aluminum alloy coating: anodized for corrosion protection hub alignment set screws are included. Longer bolts sold separately depending on application. Made in Germany. Sold individually. Can be used in front and/or rear. No...(choose a part on the right to read more)
$101.49
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$236.41
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |