Vehicles
Sections
176 not categorized PORSCHE 356 B PROPSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 GT3 2003-05 (includes uncategorized and accessory items) 2110901 Unique design actually grips steering knuckle for extra strength. Combined with a super strong 12mm grade 12.9 bolt, this is a sturdy solution. Height adjustable from .50" to 1.25" in 1/8" increments by positioning 3 spacers above/below steering knuckle. Articulates an impressive +/- 27 degrees to prevent binding at full compression and droop. Bump steer is a change in toe setting resulting from vertical wheel displacement. A car that bump-steers requires constant adjustment at the steering wheel to maintain a steady trajectory over uneven surfaces. This can be handful to drive. The 911/914 series has some bump steer inherent even in the stock configuration. The problem becomes more severe with lowered ride ...(choose a part on the right to read more)
$388.80
Make a selection 10010303808 The 11.8:1 compression will provide you with more acceleration than kits with 11.3:1 compression. However, this kit cannot be used with original cams, it requires a more aggressive cam (maximum valve lift (tdc) of 2.1 mm) and has very deep pockets for use with rsr valves. The 109-mm size means that the housings must be modified on non rennsport models. If you have a European rennsport model, these would be slip fit. This kit also requires the larger o-ring seals, part # 96410440180 and larger base gaskets, part # FVD116929. Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resi...(choose a part on the right to read more)
$13,111.19
Make a selection 100124100 Double row ims bearing version (original cover dish depth = 13.34 mm).
$838.68
Make a selection NLA62800500 For 12 volt conversions we have an inexpensive unit which is wired in line to the wiper motor. This small module will reduce 12 volts input to your 6 volt motor. The rheostat on the switch will still work properly. It can be mounted either under the dash, or on t-6/c cars, it can go next to the fuse block.
From $133.11
Make a selection PNA70202000 Finally; all stainless steel license plate frames.no more rust stains! From Porsche, of course. Appropriately finished and packaged with matching colored caps for your screw heads(4).
$66.56
Make a selection 644531035 This rubber wedge-shaped piece is a door check. Properly installed, it makes a thump noise when the door is being closed. They are symmetrical and can be used on either side of the car. Installation is possible with the door in place.
$31.49
Make a selection T55100204 Oil seal installer, flywheel end. Specially manufactured to our specifications, these tools make it easy to properly install the rear crankshaft seal. They fully support, position and press the fragile oil seal into place without distortion. For all 356 engines.
$89.05
Make a selection NLA50504900 This rubber base is the correct width for the bumper decos. Bases available by other vendors are three pieces which must be crudely glued together. Our piece, when properly installed, will look very original. The ends must be finished according to the 356a workshop manual -- instructions are provided.
From $56.52
Make a selection PNA70200300 Finally; all stainless steel license plate frames.no more rust stains! From Porsche, of course. Appropriately finished and packaged with matching colored caps for your screw heads(4). Comes with "Boxster" insert, "Porsche" shownt
$65.79
Make a selection PNA70201900 Finally; all stainless steel license plate frames.no more rust stains! From Porsche, of course. Appropriately finished and packaged with matching colored caps for your screw heads(4).
$66.56
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |