![](https://30ed524141d0cac60ab4-d2e2d18a14257de3b9ce428cf077ee97.ssl.cf2.rackcdn.com/acban.jpg)
PORSCHE 944 S2 INST RINGCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 GT3 2003-05 - Transmission (includes uncategorized and accessory items) ![]() FVD33300902AT Send us your original spring plate and we will have it reconditioned for you. The reconditioning process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and media blast the part. Once fully prepared, we install new rs spec. (85 shore) rubber bushings/bearings. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Then we seal the spring plate with a corrosion resistant plating. Sold individually. 2 necessary per car. Please note: this only fits cars with the g50 transmission.
$274.89
Make a selection 22011099706 The 997 turbo ipd "y" pipe was built for the more demanding turbo performance customer. The factory y pipe becomes restrictive when adding substantial power gains. The ipd "y" pipe has larger inlets and an optimized diversion area allowing for even greater power gains. This superior and more efficient design flows 126 more cfm than the factory y pipe delivering the additional power needed to raise the performance bar on any turbo. The ipd "y" y pipe is designed to be a direct replacement of the factory OEM y pipe. There are no modifications or fabrication required for installing the ipd y pipe. This is an easy and straight forward r & r (remove and reinstall) bolt on upgrade. Note: contains everything nec...(choose a part on the right to read more)
$1,149.23
Make a selection 930123002X This remanufactured turbo is a direct replacement for original part # 930 123 002 00. The remanufacturing is completed in Germany by kkk/borg warner certified technicians. This ensures reliability, superior performance and cost effectiveness. The remanufacturing process includes: complete disassembly. All parts are cleaned, inspected and measured for tolerances. Turbine wheels are replaced. Thrust bearings are replaced. All new seals are installed. Internals are reconditioned. Parts are balanced (static & dynamic) according to balancing protocol. For a complete installation we recommend adding a gasket, part # 93012319105 an intake sleeve, part # 93011015801 and be sure to have a few spare studs on hand, part #...(choose a part on the right to read more)
From $3,130.83
Make a selection 930105136001 Genuine gear, sourced in Germany to ensure quality, reliability and precise fitment. We recommend ordering 6 qty. Oil pump lock plates part # 99903900100 for installation. Please note: please check the model fitment tab to ensure accurate fitment. Sold individually. 1 necessary per car.
$421.58
Make a selection 93010501314 Genuine intermediate shaft and gear, sourced in Germany to ensure quality, reliability and precise fitment. We recommend ordering 6 qty. Oil pump lock plates part # 99903900100 for installation. Please note: please check the model fitment tab to ensure accurate fitment. Sold individually. 1 necessary per car.
From $1,744.05
Make a selection 93060201501 Complete distributor without an exchange. This distributor has been completely remanufactured, which includes a full inspection, disassembly, cleaning and degreasing. We then install a toothed timing belt, 3 German made top bearings, 1 German made lower bearing and a distributor pinion pin (part # 930 602 922 00). We also install new dust caps, Bosch rotors and Bosch cap. Clearances, timing and proper operation are then checked to ensure reliability.
$2,661.20
Make a selection 93010734714 This part is sourced in Germany to ensure quality, reliability and precise fitment. This will fit all the vehicles listed in the fitment tab and those that have been updated to pressure fed tensioners. This line requires that you also purchase part # 93010734706 . We also recommend purchasing 1 qty. Union nut, part # 90010400303 and 1 qty. Cutting ring sleeve, part # n0208251 for installation. Also need the right side? Please order part # 93010734812 for the 911 3.2 l and 930 3.3l. Order part # 93010734815 for the 965 3.3 l. Sold individually. 1 necessary per car.
From $43.89
Make a selection FVD35199607ZB Wheel spacers make your tires and wheels appear wider by moving the wheel out from the hub, providing both performance and appearance improvements. Whether you want improved handling, increase safety, or simply desire your car to make a statement about your individual style, wheel spacers can help you accomplish your goal. FVD BrombacherGermany conveniently combines Porsche specific h&r spacers, the correct Porsche bolt shoulders and the correct length h&r bolts to take the guess work out of adding spacers to your car. Our spacers are cost competitive and have been developed to work together without compromise. Don't be fooled by the competition whose costs quickly add up by requiring you to order the spacers...(choose a part on the right to read more)
$107.42
Make a selection 96442422300 Restore precise shifting with this OEM shift coupler bushing. To save on installation cost / time, we recommend installing a new conical screw, part # 90142422900 coupler sleeves / boots, part # 91142429400 and 91142429200 be sure to check / replace the shift rod bushing as well, part # 91142413900, the friction ring, part # 91442422400 this is a high-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per car.
From $5.88
Make a selection 99310524713 Genuine camshaft for 993 models from 1994-1995 with the engine numbers m64.05/06/07/08. We recommend having the opposite camshaft inspected and if it is necessary to replace, order part # 99310524713 sold individually. 1 necessary per vehicle. Please note: professional installation is required. Different manufacturing tolerances require an inspection of the free clearance of all parts!
$979.44
Make a selection FVD1161022 Hailing from the baden wurttemberg region in Germany, speaking the language and dealing with lead engineers from the OEM and motor sport manufacturers for more than 30+ years has many advantages. Our FVD exclusive line of clutch kits is culmination of Porsche genuine parts, zf sachs race engineering gmbh parts and motorsports parts that have been developed to work together without compromise. They offer a silky smooth release, superb drivability, can handle more torque (370 ft/lbs. / 500 nm max.) than comparable stage 1 type recommendations. These kits are perfect for street and light track use. We specifically chose a clutch disc with torsion springs that function as a vibration damper between engine and gearb...(choose a part on the right to read more) General Fitment911 GT3 2007-11911 GT3 2003-05 911 1994-98 911 1989-94
From $1,731.35
Make a selection FVD123011Y These actuators are assembled with springs for higher boost levels. Additional springs are available for tuning to custom boost level. These replacement actuators are supplied complete with brackets ready to install.
$34.65
Make a selection FVD33300905 This rear spring plate is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New rs spec. (85 shore) rubber bushings are installed to make this a direct bolt on. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Features: made from ¼ inch spring steel includes new rs spec. (85 shore) rubber bushings made in Germany sold individually. 2 necessary per car.
$287.60
Make a selection 99312301352ATK Our k-16 remanufactured turbo is cost competitive and is a direct replacement. Simply send us your original k16 turbochargers and a borg warner / kkk certified technician will remanufacture your turbo. The remanufacturing process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will replace the turbine wheels, thrust bearings, install new seals, install new waste gates, recondition the internals and high speed balance the turbo. This ensures reliability and superior performance for many years to come. The remanufacturing is done on an exchange basis only. You must send us your original k16 turboc...(choose a part on the right to read more)
$2,304.23
Make a selection AP958170 Agency power is proud to release its super sport exhaust system for the 958 Porsche Cayenne s v8 2011 and up. the super sport exhaust is a axle system that gives your 4.8l v8 engine a real aggressive tone. made here in the usa, the exhaust saves close to 30lbs off the rear end of the vehicle. using 304 stainless steel and detail oriented tig welding, the exhaust system uses two small high flow mufflers which give it the sports car rumble. its reduced back pressure design gives the engine improved horsepower and torque with most noticeable improvement in throttle response. because of the reduced restriction, this exhaust horsepower gains can definitely be noticed in the mid to top rpm range.
$1,570.75
Make a selection 96434703200SP We are committed to Porsche cars and are very happy to release an outer tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 032 00. This is ideally suited for use with our monoball inner tie rod, part # 96434705805sp for the 964 c2 / turbo look or 965 or part # 96434705804sp for the 964 c4 or rs. Please note: this is not for the wide body. Sold indiv...(choose a part on the right to read more)
$338.28
Make a selection 96434307281ATK Looking for a more cost-effective solution than ordering a new link? Let us recondition your original drop link. The reconditioning process includes full inspection, disassembly, degreasing and media blasting. Once fully prepared, we properly install new bushings, finish with a corrosion proof coating and include a new lock nut. Please note: each link is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your link we will notify you as soon as we can. Arrangements can be made for its return to you. Sold individually. 1 necessary per car.
$204.44
Make a selection 96434350301 This is the lower strut plate that retains the spring and sits on top of the adjusting nut. We recommend that you inspect and replace if necessary with any new shock install. This plate tends to suffer from corrosion as debris collects in it with time. Sold individually. Right or left side fitment. 2 necessary per car.
From $39.00
Make a selection FVD116981GT4 Hailing from the baden wurttemberg region in Germany, speaking the language and dealing with lead engineers from the OEM and motor sport manufacturers for more than 30+ years has many advantages. This FVD exclusive clutch kit is culmination of zf sachs race engineering gmbh parts and an aasco motorsports lightweight flywheel that have been developed to work together without compromise. This kit offers a silky-smooth release, superb drivability, can handle more torque than comparable clutch kits. We specifically chose a clutch disc with torsion springs that function as a vibration damper between engine and gearbox that is necessary when removing the factory dual mass flyweel (dmfw). It also means that you will e...(choose a part on the right to read more)
$2,770.85
Make a selection BK7081 The haynes manual is the world's best selling vehicle repair manual. Hundreds of pictures with easy to follow step-by-step instructions make any repair a snap! Everything from a simple tune-up to a major engine overhaul are included in these handy manuals. The electrical wiring diagrams as great too. Specify make, model and year for your car or motorcycle. General FitmentACCESSORYBOXSTER 1997-04
$28.35
Make a selection BES99305040S FVD is proud to introduce our newest line of Brombacherexhaust systems. Brombacher exhausts are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredible value. All of our exhausts are manufactured in Germany and are tested comprehensively for flow rate and characteristics, thermal stress, resistance to cracking, and longevity. Brombacher mufflers outer shell dampens and eliminates unwanted frequencies and ensures no resonance or drone in the cabin. The end result is a strong, linear, firing-order dominated flat-6 Porsche sound. In addition, Brombacherexhausts systems are available for ultimate performance full titanium. Our titanium system's are nearly...(choose a part on the right to read more)
$1,911.53
Make a selection FVD1109115043 This replica high butterfly mfi throttle bodies system is for those looking for ultimate engine performance as well as an authentic rsr engine appearance. This kit keeps air consistently on tap for superior drivability. When the throttle is opened, there is an instant injection of air, providing a sharp, crisp throttle response. This efficient injection frees up more power and compliments larger displacements, high lift cams and full exhaust systems. This kit is engineered, precision machined, flow tested and manufactured in Germany. It is replicated to look as close to the original as possible. Intake trumpets (velocity stacks) are available in your choice of red or black. Includes: 6 individual stacks (50 mm ...(choose a part on the right to read more)
$7,829.75
Make a selection F6564120102 Instrument faces are one of the most visible and frequently looked at components in your Porsche. When making the decision to change them you want to make ensure that you select a high quality product similar to your originals. Each of our sets are made in Germany and use the factory scripting (font). Our faces also offer the same uniform night time shading and includes the original die cut notches for easy installation. Each kit is made for global distribution, so simply pick out the faces that match your originals. They are available in a variety of colors to make a bold statement, or to match exterior paint schemes. This kit includes faces for: manual transmission / tiptronic transmission / kph / mph / celsi...(choose a part on the right to read more)
$634.10
Make a selection FVD1161021 The discs rigid hub with organic friction material has superior thermal resistance, is more resistant to higher rpm's than the oe discs, offers greater longevity and is able to transmit higher torque (370 ft/lbs. / 500 nm max.). It is an ideal kit for lightly modified street or light use track cars. Clutch kit is made in Germany and includes: 1 qty. Clutch disc (zf sachs race engineering, gmbh) 1 qty. Pressure plate (zf sachs race engineering, gmbh) 1 qty. Release bearing 1 qty. Spline lubricant 9 qty. Pressure plate screws kit weighs 13 lbs. (6 kg) tech tip: when you are planning to install a new clutch, it is a good idea to replace the clutch release fork and shaft to ensure proper clutch engagement. Our par...(choose a part on the right to read more) General Fitment911 GT3 2007-11911 GT3 2003-05 911 1994-98 911 1989-94
From $1,201.38
Make a selection FVD160924000 Bosch micro edge excel wiper blades clean windshields better and last longer than ever before. This ultra performance wiper blade features an exclusive dual rubber compound with a fully-enclosed metal tension spring, housed in an aerodynamic steel frame. The result is less streaking and unmatched resistance to wear from weather and corrosive elements. And with the exclusive Bosch directconnectâ„¢ one-step system, installation is quick and easy.
$25.41
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |