PORSCHE 996T INST SETCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 GT3 2003-05 - Engine (includes uncategorized and accessory items) 00004490042 Cabriolets are not known for having great acoustics inside the passenger compartment. However, the new Porsche Boxster high performance audio system changes all that. Explicitly designed for the interior and layout of the Boxster, the system delivers outstanding performance with either the roof on or off. The specially designed amplifier delivers two channels of 160 watts each, powering 2 ohm speaker sets. Two high-quality mid-range/tweeter systems coupled with a dual bass system in the door deliver incredible sound while being elegantly integrated within the Boxster's interior. Installation requires some knowledge of stereo installation, but in general is not too complicated. Beethoven or boston, the music wi...(choose a part on the right to read more)
$4,424.73
Make a selection 44404480062 High quality polished center console set that includes a polished carbon handbrake, the upper switch and lower switch covers made ready for installation. Each piece is a carbon overlay, meant to be adhered to your original plastic trim covers. We recommend adhering the carbon overlays to your originals with würth bond and seal (sold separately).
$1,533.84
Make a selection FVD33105900 Replace worn-out rear trailing arm bushings with our FVD sport bushings, made of rubber with an 85 shore hardness value that is the same as the rs models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. This is a direct replacement for original part # 90133105900 features: better handling makes precision adjustments of the suspension easier does not produce any noise like the teflon bushings. Rubber has a shore hardness value of 85 (like rs models) fit's like oem, simple installation made in Germany set is sold per axle. 1 necessary per car.
$161.70
Make a selection FVD33150040 Replace worn-out original rear sub frame (side panel) bushings and return your car to its original ride quality with this cost effective alternative. This bushing is made in Germany. It is crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value core. This is a front and rear bushing for one sub frame. 2 are necessary per car. If you are looking for a sportier upgrade we suggest our clubsport sub frame bushing set, part # FVD33150040r. We also sell complete sub frames with the bushings installed, part # FVD331993001.
$438.90
Make a selection FVD11196415GKT This installation kit is needed to install our part numbers FVD 111 964 15 or FVD 111 964 17. Sold as a set. 1 necessary per car.
$45.05
Make a selection FVD34350501 Worn bump stops and bellows can cause premature shock damage. We recommend replacing the stops and bellows with any new shock install. This set includes 2 qty. Front bump stops 96434330100 and 2 qty. Front bellows 96434350500 sold individually. 1 necessary per car.
$109.64
Make a selection FVD160993000 Bosch micro edge excel wiper blades clean windshields better and last longer than ever before. This ultra performance wiper blade features an exclusive dual rubber compound with a fully-enclosed metal tension spring, housed in an aerodynamic steel frame. The result is less streaking and unmatched resistance to wear from weather and corrosive elements. And with the exclusive Bosch directconnectâ„¢ one-step system, installation is quick and easy. Front drivers and passengers side wiper set.
$34.65
Make a selection FVD331993001 Our new rear sub frames contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. It offers rs style handling characteristics, superior durability and is still forgiving enough for street use. FVD clubsport sub frame facts: - better handling. - makes precision adjustments of the suspension easier. - does not produce road noise. - shore hardness value of 85. - direct OEM replacement. - more forgiving for street use. - new sub frames with inserts installed. Sold as a set. 1 kit is necessary per car.
$1,846.85
Make a selection F9764199703 Instrument faces are one of the most visible and frequently looked at components in your Porsche. When making the decision to change them you want to ensure that you select a high-quality product like your originals. Each of our sets are made in Germany and use the factory scripting (font). Our faces also offer the same uniform night time shading and include the original die cut notches for easy installation. Sold individually. 1 necessary per car. Please note: we recommend professional installation due to the intricacies of the instruments, needles, necessary tools and calibration. We have recommended installers in the u.s., contact us for further details.
$340.73
Make a selection MSPP009 These side stripes give your Porsche a great presence on the street! An original dealer installed item and factory equipment, these stripes look great on vintage cars and gives new Porsche a retro-racing touch. They are easy to install using a little soapy water and masking tape guide line. Stripes are 76.5 inches long. Sold as a set of two, one for each side of your car. General FitmentALL914 1970-76
$85.00
Make a selection E13209 Introducing the latest in tow hook innovation: engineered with an increased side load capacity and adjustable-length rigid mount receiver. This tapered stainless loop design incorporates a new locking function to maintain your preferred loop position. Additional features include machined graphics, rotational timing and camera mount compatibility.
$152.25
Make a selection BES99716000S1 Our exhaust products are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredible value. Our entire "brombacher" line of exhausts is manufactured by m&m exhaust, gmbh in Germany who is no stranger to Porsche racing exhausts. Each is tested comprehensively for flow rate, thermal stress, resistance to cracking, and longevity. To further ensure quality, m&m use lightweight, motorsports grade German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. Features: polished stainless steel double walled to dissipate heat so discoloration will take longer to appear / easier to polish out includes clamps for installation fits the factory cut outs i...(choose a part on the right to read more)
$893.97
Make a selection AP9972TT170 The stock exhaust of the Porsche 997.2 turbo is very restrictive compared to aftermarket systems. Porsche does this to meet sound and emission purposes like most OEM manufacturers. agency power set out to create an exhaust system for the new Porsche 997.2 turbo 6speed or pdk that did not drone, would produced amazing performance, and under throttle give an incredible sound. we have accomplished this! the new agency power exhaust not only saves about 30lbs off the rear end, it also improves power quite a bit.
$3,937.45
Make a selection TL661 Allows you to remove and install springs quickly and safely when repairing struts! Set of 2 compressors with extra-wide (3") dual claws maintain spring curvature, which is necessary to seat springs. Minimum tensile strength of bolts: 105,000-psi. Made of drop-forged, heat-treated and chrome-plated carbon steel. General FitmentACCESSORY
$59.85
Make a selection FVD504993RS Made of polyurethane so they will not chip or crack like fiberglass, and are flexible enough to survive small impacts. Simple installation without any modifications to the original bodywork. Sold as a set (left and right). Not for wide body cars (993 turbo or turbo-look). Please note: these are aftermarket products. All aftermarket products need to be prepped, sanded, gaps checked / filled and painted. We only recommend professional installation with a shop that has aftermarket bodywork experience.
$731.12
Make a selection FVD51299102MM The moshammer vented rear diffuser with fins is an aggressive design that reduces aerodynamic drag. This vented diffuser allows air that is trapped by the rear bumper to exit, allowing for greater top end performance. The design also incorporates 5 fins that improve laminar airflow by reducing turbulence. Moshammer manufactured this as a direct replacement, so it secures seamlessly to the factory locations with the original hardware. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of the downforce rs (991.1 turbo/s) package, the result is a confident, cohesive stance with balanced downforce. Features: ve...(choose a part on the right to read more)
$1,533.84
Make a selection BBI9911070001 The bbi autosport intercooler kit is a direct replacement upgrade for the Porsche 991 turbo. Designed with 3d modeling & computational fluid dynamics software, this bespoke intercooler features 3d printed and cfd tested end tanks, and offset cores for optimum flow and improved performance. The advanced 3d printing manufacturing process allows complex design and shapes to be produced for optimum flow. This kit is ready for installation (plug & play), using the stock plumbing and shrouds. When engineering, technology, and the right people are fueled by passion, the results are impressive.
$4,614.75
Make a selection MSPP013 These side stripes give your Porsche a great presence on the street! An original dealer installed item and factory equipment, these stripes look great on vintage cars and gives new Porsche a retro-racing touch. They are easy to install using a little soapy water and masking tape guide line. Stripes are 76.5 inches long. Sold as a set of two, one for each side of your car. General FitmentALL911 1978-83
$89.25
Make a selection FVDB2435500 FVD Brombacherstainless steel brake lines for Porsche are manufactured in europe and are approved for all abs systems. They consist of a ptfe teflon inner liner surrounded by a stainless steel (inox) braided cover. They are also coated in a uv resistant pvc jacket to protect the wire and inner hose from the elements, chemicals and abrasion. This construction ensures minimal expansion inside the hose core and eliminates that "spongy" brake feel that is commonly found in the OEM brake lines. FVD Brombacherhas been tuning Porsche vehicles for over 30 + years now, so rest assured that our lines are a direct bolt on replacement for each Porsche application. Our lines are DOT approved by conforming to the fmvss 1...(choose a part on the right to read more)
$166.32
Make a selection 91133300900BHD Bushings set with instructions:w/ 80-85 shore a hardness
$31.38
Make a selection 91455923510TS Beautifully chromed auto atlanta 914 driving light grill set for your car. Make sure you buy our grill installation kit for new hardware to match these new grilles (b914559kit)
$80.00
Make a selection 90134142102KHD Front; 4pc set of heavy duty stiffer rubber bushings; instructions included
$41.48
Make a selection FVD7219649401 This auxiliary chain tensioner tool is required to be installed in place of the hydraulic tensioners whenever checking or adjusting canshaft timing. These tools ensure proper specified preload is placed on the timing chain to ensure accuracy whenever cam timing is checked or modified. Set of two timing chain tensioners.
$380.00
Make a selection BES99126010S Our exhaust products are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredible value. Our entire "brombacher" line of exhausts is manufactured by m&m exhaust, gmbh in Germany who is no stranger to Porsche racing exhausts. Each is tested comprehensively for flow rate, thermal stress, resistance to cracking, and longevity. To further ensure quality, m&m use lightweight, motorsports grade, t 316 stainless steel material. Features: polished stainless steel double walled to dissipate heat so discoloration will take longer to appear / easier to polish out includes clamps for installation fits the factory cut outs in the bumper perfectly can be adjusted for...(choose a part on the right to read more)
$630.63
Make a selection MSPP001 These side stripes give your Porsche a great presence on the street! An original dealer installed item and factory equipment, these stripes look great on vintage cars and gives new Porsche a retro-racing touch. They are easy to install using a little soapy water and masking tape guide line. Stripes are 76.5 inches long. Sold as a set of two, one for each side of your car. Script is 3 feet long. General FitmentALL
$85.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |