Vehicles
Sections
268 not categorized PORSCHE CAYMAN CON RODCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 2005-08 (includes uncategorized and accessory items) 846R9033 Material: 1.5" x 1" x .125" wall carbon steel tubing General Fitment911 GT3 2007-11911 TURBO/GT2 2007-09 911 2009-12 911 2005-08 911 GT3 2003-05 911 TURBO/GT2 2001-05 911 1998-05 CAYMAN 2009-12 CAYMAN 2006-08 BOXSTER 2009-11 BOXSTER 2005-08 BOXSTER 1997-04
$128.00
Make a selection 95037013 Stoptech brake lines consist of a ptfe (commonly referred to as teflon) inner line that carries the brake fluid, which is then covered with a layer of stainless steel woven braid. The ptfe tube is very resistant to expansion under pressure and will not degrade from exposure to brake fluid. every stoptech brake line is 100% tested in-house to a pressure of 4,500 psi. This is almost 4 times the typical line pressure exerted by a production vehicle's master cylinder. stoptech is a registered brake line manufacturer with the united states DOT and all stoptech stainless steel brake lines are manufactured to meet DOT compliance standards. Stoptech stainless steel lines also meet or exceed fmvss 106 and applicable...(choose a part on the right to read more) General Fitment911 2009-12911 1998-05 911 2005-08 911 GT3 2003-05 911 TURBO/GT2 2001-05 911 TURBO/GT2 2007-09 911 GT3 2007-11 911 TURBO/GT2 2010-13 CAYMAN 2009-12
$66.59
Make a selection EIP073MX72 Endless ewig mx-72 rear brake pads Porsche Boxster 2.5l 2.7l 97-03 General FitmentBOXSTER 1997-04BOXSTER 2005-08 911 2005-08 CAYMAN 2006-08
$524.48
Make a selection 10610 Billet aluminum ims to crankshaft chain guide/tensioner, replacement for Porsche part no. 996 105 165 55, to help prevent catastrophic engine failures like this. Shown below is a comparison of our billet tensioner paddle compared to the cast factory tensioner. Billet construction provides a significantly stronger and more durable product while utilizing oe Porsche wear pad and pressure pin (both of which are included as shown). Update: we've found the factory plastic pressure pin to not be strong enough, so we've made a billet steel pressure pin against which the chain tensioner actuates to tension the crankshaft to ims drive chain. This is a return to a style of pressure pin found in very early examples of t...(choose a part on the right to read more) General FitmentBOXSTER 1997-04911 1998-05 CAYMAN 2006-08 BOXSTER 2005-08 911 2005-08
$337.00
Make a selection S1117 For a perfect fit, reliability you can depend on, full adjustability, and optimum performance, the factory GT3 swaybar is the best on the market. We have packaged them together with new bushings and our adjustable drop links to provide you with a wining combination. The light weight hollow 26.8mm od sway bars are half the weight of a solid bar with the same stiffness. Complete with fully adjustable front drop links to eliminate suspension preload. Correctly sized, precision, teflon-lined rod-ends for smooth and quiet operation, long life, and high reliability. No wear and rattling problems, like those seen with other designs, due to undersized or low quality rod ends. All necessary hardware is provided in zinc ...(choose a part on the right to read more) General FitmentBOXSTER 2005-08911 2005-08 911 GT3 2007-11 CAYMAN 2006-08
$657.25
Make a selection S701041 Rennline adjustable control arm links solve both these problems. Manufactured from 6061 aluminum and feature a turnbuckle design that allows each arm to be lengthened or shortened as needed to restore proper suspension geometry on a lowered Porsche. The fk teflon-lined rod end bearings ensure precision handling and lock in your car's alignment settings, ensuring predictable cornering under all conditions. Unlike the competitors' product, rennline arms come with eccentric locks and new hardware so you can completely eliminate the factory setup, which is known to go out of adjustment under hard driving and ruin your car's alignment. Note: two required per car. General Fitment911 1998-05911 TURBO/GT2 2001-05 911 GT3 2003-05 911 2005-08 911 GT3 2007-11 CAYMAN 2006-08 BOXSTER 2005-08
$322.25
Make a selection RS21 Under extreme conditions, such as road racing and autocross, negative camber is required to keep as much of the tire’s contact patch on the road as possible. Stock suspension mounts will not allow you to achieve the necessary amount of negative camber required for this type of performance driving. Rennline’s sealed camber plates incorporate fk motorsports spherical bearings and eliminate the indistinct feedback associated with factory rubber mounts. Comes as a set of two. Why are rennline’s strut mounts the best ? General FitmentBOXSTER 2005-08CAYMAN 2006-08 911 2005-08 911 GT3 2007-11
$634.10
Make a selection SA03 These brackets have been specially designed to allow you to install both, factory seat belts and aftermarket harnesses at the same time. Intended for the use of quick disconnect lap belts on both sides of the seat. This is a perfect set up for your street/track car. All brackets are designed to attach to the factory seat belt mounting locations so no drilling is required. General Fitment911 1965-69356 1960-65 912 1965-69 911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89 911 1989-94 911 1994-98 911 1998-05 911 TURBO/GT2 2001-05 911 GT3 2003-05 911 2005-08 911 GT3 2007-11 944 1989-91 944 1985-88 944 1982-85 928 1992-95 928 1987-91 928 1983-86 928 1978-82 924 1986-88 924 1980-85 924 1976-79 914 1970-76 CAYMAN 2006-08 BOXSTER 2005-08 BOXSTER 1997-04 968 1992-95
$56.60
Make a selection 95504480103 Group 2 + 3 seat for children from 33 - 80 lbs. / approx. 3,5 to 12 years of age. . Porsche child seats can be fitted into position quickly and securely using the standard north american latch fastening system in conjunction with the Porsche child seat fastener system which needs to be installed through your authorized Porsche dealer. Telescopic bars on the child seat lock into place between the backrest and the seat and hold it firmly to the passenger seat. Child seats may only be used in the Boxster, 911 or Cayman on the passenger seat in conjunction with the child seat fastener system. To avoid the risk of injury from a deploying airbag, never place a child age 12 or under in a front seating position without...(choose a part on the right to read more) General FitmentACCESSORY
$318.31
Make a selection 96434705804SP We are committed to Porsche cars and are very happy to release an inner tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 032 00. We also suggest replacing your outer tie rods, part # 96434703200 (qty. 2 are needed) and now is also a good time to replace your worn out inner tie rod dust bellows, part # 96434719103. Please note: this is not for the ...(choose a part on the right to read more)
$206.75
Make a selection 96442422300 Restore precise shifting with this OEM shift coupler bushing. To save on installation cost / time, we recommend installing a new conical screw, part # 90142422900 coupler sleeves / boots, part # 91142429400 and 91142429200 be sure to check / replace the shift rod bushing as well, part # 91142413900, the friction ring, part # 91442422400 this is a high-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per car.
From $5.88
Make a selection 99334703104 If your outer tie rods are worn, you will experience sloppy steering response and knocking / creaking sounds. Your outer tie rods keep the steering centered, so failure can be dangerous and can seriously affect steering control. After replacing the tie rods, you will experience tighter, more precise feedback without noise. Tie rod consists of: 1 qty. Tie rod 1 qty. Hexagon nut (m14 x 1.5) 1 qty. Inner axial joint 1 qty. Lock nut 1 qty. Dust bellows / boot we recommend replacing the right and left side tie rods at the same time. Sold individually. 2 necessary per car.
$227.10
Make a selection 83789470071 Stoptech big brake kit front slotted red caliper Porsche 996 Carrera s 2005 General Fitment911 2005-08
$3,282.93
Make a selection 51550400 For years mansory has been committed to perfection, craftsmanship and well-engineered technology. Mansory is headquartered in switzerland, allowing them to stay up to date and constantly improve upon the newest Porsche offerings. Mansory stands for driving pleasure, stylish design, and progressive engineering. Mansory's customization and cosmetic upgrades also fall in line with this performance-driven philosophy. Their vast product line offers complete aerodynamic kits, ultra-light alloy rims, and powerful engine performance parts; all of which match the high quality workmanship of the exotic vehicles they are designed for. Production meeting the highest technological standards, masterful workmanship, and the ...(choose a part on the right to read more) General Fitment911 2005-08
$6,261.17
Make a selection 51550300 For years mansory has been committed to perfection, craftsmanship and well-engineered technology. Mansory is headquartered in switzerland, allowing them to stay up to date and constantly improve upon the newest Porsche offerings. Mansory stands for driving pleasure, exclusive design, and progressive engineering. Mansory's customization and cosmetic upgrades also fall in line with this philosophy. Their vast product line offers complete aerodynamic kits, ultra-light alloy rims, and powerful engine performance parts. Production up to the highest technological standard in combination with masterful workmanship and the finest materials - that is mansory's quality standard. General Fitment911 2005-08
$6,127.93
Make a selection 99634304349 Serie production spring seat must be used! Bilstein b4 OEM (original equipment manufacturer) replacement shock absorber for your Porsche with standard suspension. The b4 damper from bilstein is the perfect replacement for your Porsche. Facts: - constant damping power under any load - high power reserves for maximum safety - ride like it's the first time, every time - OEM quality - bilstein gas pressure technology
From $452.62
Make a selection 9780929758268 The second edition of this book continues the restoration of a 356 Porsche to driver level condition. This book does not spend time or money creating the “perfect” 356, and does not necessarily search for nos (new old stock) replacement panels if a reproduction panel or patch is appropriate; but the book strives to give you a restoration that will be correct, admired and driven. This second edition provides more detail and contains additional comments to assist those restoring a 356 which was purchased disassembled. this second edition follows the restoration of a 1957 sunroof coupe from the time of purchase to the first drive. additionally, detailed comments are provided from vendors, such as media blast...(choose a part on the right to read more) General FitmentACCESSORY
$30.98
Make a selection 96534703200SP We are committed to Porsche cars and are very happy to release an outer tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM part number, 965 347 032 00. Sold individually. 2 needed per car. We also suggest replacing your inner tie rod, we have a uniball option, our part # 96434705805sp (qty. 1 is needed) and now is also a good time to replace your worn out inner tie...(choose a part on the right to read more)
$264.50
Make a selection 83789470072 Stoptech big brake kit front drilled red caliper Porsche 996 Carrera s 2005 General Fitment911 2005-08
$3,282.93
Make a selection 837896C0051 Stoptech big brake kit front slotted black caliper Porsche 996 Carrera s 2005 General Fitment911 2005-08
$3,849.93
Make a selection 83789680052 Stoptech big brake kit front drilled black caliper Porsche 996 Carrera s 2005 General Fitment911 2005-08
$4,076.73
Make a selection 83798470051 Stoptech big brake kit front slotted black caliper Porsche 996 Carrera 4 2004 General Fitment911 1998-05911 2005-08
$3,282.93
Make a selection 837896C0072 Stoptech big brake kit front drilled red caliper Porsche 996 Carrera s 2005 General Fitment911 2005-08
$3,849.93
Make a selection 99334703181 If your tie rod is worn, you will experience sloppy steering response and knocking / creaking sounds. Your tie rod keeps the steering centered, so failure can be dangerous and can seriously affect steering control. After replacing the tie rods, you will experience tighter, more precise feedback without noise. Tie rod consists of: 1 qty. Tie rod 1 qty. Hexagon nut (m14 x 1.5) 1 qty. Inner axial joint 1 qty. Lock nut we recommend replacing the right and left side tie rods at the same time. We also recommend replacing the bellows, part # pcg419831c sold individually. 2 necessary per car.
From $318.15
Make a selection 99634304342 Serie production spring seat must be used! Bilstein b4 OEM (original equipment manufacturer) replacement shock absorber for your Porsche with standard suspension. The b4 damper from bilstein is the perfect replacement for your Porsche. Facts: - constant damping power under any load - high power reserves for maximum safety - ride like it's the first time, every time - OEM quality - bilstein gas pressure technology
From $452.62
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |