Vehicles
Sections
61 not categorized PORSCHE 930 REAR BUSHINGCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1994-98 (includes uncategorized and accessory items) S727374101 If you're serious about how your 993 handles, you should upgrade the rear suspension with adjustable control arm links. There are two major drawbacks to the factory links: 1) you can't lower your car and maintain proper suspension geometry. The factory links create too much toe-in, which cannot be adjusted out, creating handling problems and excessive tire wear. 2) the factory links have rubber bushings, which make handling imprecise, especially in performance driving when suspension loads are highest. General Fitment911 1994-98
$1,899.61
Make a selection FVD33104381 The tow link is the furthest rear control arm on the rear axle. It is responsible for the toe angle adjustment. The OEM control arm bushings are simply too soft for track events and the teflon monoball racing bushings are too far too hard and noisy for street cars. Our sport bushings are made of a denser rubber (85 shore opposed to OEM 65 shore), which means that they are suitable for street and track use. Equally as important is that they do not produce any noise like the teflon bushings. FVD sport control arm facts: - better handling and more responsive. - makes precision adjustments of the suspension easier. - does not produce noise. - shore a hardness value of 85 for durability and handling. - fit's like o...(choose a part on the right to read more)
$488.12
Make a selection FVD205993001HA H&r rear sway bar with a 24 mm diameter. 2-way adjustable. This is the rear sway bar from our kit, part # FVD205993001. Includes bushings. Sold individually. 1 needed per car.
$433.62
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$236.41
Make a selection FVD3419991 This is a cost effective alternative to buying new control arms. Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with new bushings of the same rubber (65 shore hardness value). This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$134.24
Make a selection 99333104503ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install the bushings. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for its return to you. We do not offer a core exchange on this part.
$283.93
Make a selection 99333104102 The lower control arms bushings and ball joint can fail, pushing your alignment out. Improper alignment and incorrect suspension geometry leads to excessive tire wear. Please note: these are commonly referred to as wishbones or a-arms. Sold individually. View/Change Diagram
From $1,216.51
Make a selection 96433379200 Known as: stabiliser mounting / rubber mounting View/Change Diagram
From $14.14
Make a selection 99333105180 The bushings are made of rubber with an 85-shore hardness value, which is more durable, provides more positive suspension location and is still quiet and comfortable for street use. Sold individually.
From $825.66
Make a selection 99333105280 The bushings are made of rubber with an 85-shore hardness value, which is more durable, provides more positive suspension location and is still quiet and comfortable for street use. Sold individually.
From $825.66
Make a selection 99333105100 The bushings are made of rubber with a 65-shore hardness value, which is more comfortable for street use. Sold individually. View/Change Diagram
From $889.81
Make a selection FVD721TB90P2
$225.72
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |