PORSCHE 986 REAR LEDCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1994-98 - Transmission (includes uncategorized and accessory items) 150TBF900 Replace worn-out original front control arm / wishbone bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This is located at the front of the control arm / wishbone. The correct matching poly-graphite bushing for the rear of the control arm is part # 150tbr900 sold individually. 2 necessary per car.
$50.82
Make a selection FVD803993VR0222 High quality, German made three-point replacement safety belt, designed to perform like the original. Features / specs: belt length: 300 cm (118 inches) 3 point inertia reel belt angle adjustable reel (max. Of 8 *) includes 22 cm (8.5 inch) buckle, installation hardware and caps. Din-en-iso 9001: 2000 quality standard manufactured, e-mark approved. The matching rear belt is part # FVD803993hr sold individually. 2 necessary per car.
$196.35
Make a selection FVD911503185186 This seal kit consists of original part # 911 503 185 00 (left) and 911 503 186 00 (right). The set can be used on the trailing edge of the front fender at the cowl just below the windshield. It is also used under the back of the rear quarter panel where it meets the bumper side panel. Genuine part sourced from Porsche ag in Germany to ensure quality, reliability and precise fitment. Sold as a set. 1 set is necessary for front fenders and one set is necessary for the rear. Please note: this is the thinner width. This is not the thicker width from the SC models.
$15.68
Make a selection FVD721T221 Camber adjuster needed to adjust toe - in of the rear suspension.
$16.17
Make a selection 240991351GS Pagid yellow rsl 29 are from the rsl line of endurance racing brake pads. They are a medium friction coefficient racing compound with long pad and disc life, and are easily bedded in. Rsl 29 pads are manufactured of a low metallic resin bonded material containing steel and acrylic fibers. They operate in a wide operating temperature range and offer excellent release characteristics. Rsl29 pads offer low heat conductivity and work well with abs systems. They offer excellent modulation and controllability. They offer lower disc wear rates and are fade resistant up to a temperature of 650*c (1,202*f). Applications include: club racing, track days, touring cars, prototype endurance racing and GT cars. Features at a...(choose a part on the right to read more)
$743.82
Make a selection 5007206905 This is a perfect gift or great to have for your collection! It is colorful red, white & blue, very detailed because you can see on one side the front of a racing Porsche 911 GT3 rs and on the other side the rear of the car. It is also very unique because of the picture from a Porsche inside the cup.
$28.00
Make a selection 90133300309B This rear spring plate is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New OEM spec. (65 shore) rubber bushings are installed to make this a direct bolt on. Features: made from ¼ inch spring steel includes new OEM spec. (65 shore) rubber bushings made in Germany sold individually. Left or right-side fitment. 2 necessary per car.
$322.25
Make a selection 911561053003EQ Rear window cabrio top section, manufactured in Germany with original sonnenland material. It is as close to the original as possible and is cut and trimmed to fit perfectly. Sonnenland material consists of 3 layers, dyed acrylic twill weave top layer, elastomeric rubber inner layer and polyester woven base layer. It provides increased strength against abrasion, increased fade resistance and the tighter woven layers for the mechanically operated tops. Sonnenland high quality material was originally used by Porsche and other top German manufacturers. Made in Germany. Sold individually. 1 necessary per car.
$1,033.73
Make a selection 11599700H Without pasm cars - lowers the front 1.2 inch (30 mm) and the rear 1.2 inch (30 mm). Pasm cars - lowers the front .8 inches (20 mm) and the rear .8 inches (20 mm).
$539.04
Make a selection 150PB100916 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$46.20
Make a selection 115993S Lowers the ride height by 35 mm (1.4 inches) in the front and 30 mm ( 1.3 inches) in the rear - like European m030. H&r sport springs are the ideal solution for the enthusiast who appreciates race-bred components designed for street use. Product benefits: sporty appearance improved handling characteristics lowered center of gravity linear or progressive spring design compatible with oe and aftermarket shock absorbers powder coated (purple) for anhanced appearance and corrosion resistance delivered with TUV approval engineered, manufactured and tested in Germany
$580.80
Make a selection 115900993B12 If you're looking for the perfect combination of sporty dynamics, a superior appearance and high performance, you're on exactly the right track with this sport suspension. This kit is a direct replacement for the factory mo33 kit and will give you the same performance characteristics. -professional cornering system pcs -precise response, excellent driving performance and high reserves of safety -lowering up to 10 - 15 mm in front and rear -eibach pro-kit performance springs with progressive characteristic -springs and shock absorbers road-tested and fine-tuned to complement one other perfectly -bilstein gas pressure technology -bilstein mono-tube/upside-down technology, made in Germany -German TUV certificate...(choose a part on the right to read more)
$2,371.31
Make a selection FVD205996004 Front 26mm (not adjustable) rear 23mm (3 way adjustable)
$891.66
Make a selection 992CAT With over 25+ years of Porsche air and water-cooled experience, fabspeed motorsport usa offers a great enhancement for your stock exhaust or aftermarket exhaust on your Porsche 992 Carrera. Using only the highest quality helical valves imported directly from the u.k., our system eliminates any risk of failing exhaust valves. Helical limited in great britain supplies the world's very best exhaust valves to Porsche, ferrari, lamborghini, mclaren, aston martin, and other hypercar manufacturers. Other cheap aftermarket exhaust valves are not able to handle the heat produced by a rear or mid-engine car and are guaranteed to fail, break and rattle. Helical u.k. Imported exhaust valves are bullet-proof and never fai...(choose a part on the right to read more)
$5,508.25
Make a selection FVD205996003VAG These bushings are made for h&r front sway bars with 25 mm diameters. They are a direct replacement for our part # . These will also work on any bar with a 25-mm diameter. If you would also like to replace the rear, please use part # FVD205996003hag sold as a front set. 1 set needed per car.
$61.22
Make a selection 93035204601EQ The zimmermann OEM brake disc combines high-quality cast materials, a vented and perforated braking surface and includes z-coating. Features: better wet braking performance by permanent expulsion of brake dust and water. Sporty look. Anti corrosion "z-coating" prevents rust. Noticeable improvement in braking performance. Countersunk holes double as wear indicator. Simple bolt on, modifications are not necessary. Made in Germany. Sold individually. 1 necessary per car. Rotors should always be changed in pairs; the rear left is part # 93035204501eq
$249.48
Make a selection FVD205997003 Only for cars with pdk front 24mm - not adjustable rear 24mm - 4-way adjustable
$870.87
Make a selection FVD205996003HAG These bushings are made for h&r rear sway bars with 24 mm diameters. They are a direct replacement for our part # FVD205996003. These will also work on any bar with a 24-mm diameter. If you would also like to replace the front, please use part # FVD205996003vag sold as a front set. 1 set needed per car.
$61.22
Make a selection 964561005016HA This is a complete cabrio top made in Germany with original sonnenland material. It is as close to the original as possible and is cut and trimmed to fit perfectly. Includes a trapezoidal pvc plastic rear window with a zipper like the original. If the window gets hazy simply unzip, remove and add a new window. Sonnenland material consists of 3 layers, dyed acrylic twill weave top layer, elastomeric rubber inner layer and polyester woven base layer. It provides increased strength against abrasion, increased fade resistance and the tighter woven layers are made for modern electric tops with stronger frames, like the 911 and 964. Sonnenland high quality material was originally used by Porsche and other top German ...(choose a part on the right to read more)
$2,311.16
Make a selection 96433102200RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$705.71
Make a selection BBI9974010001 Features
$1,989.75
Make a selection 96454303502 Necessary when replacing your right rear quarter window, as this seal retains the window in the body and prevents moisture from getting in. For 964 coupe models. Sold individually. 1 needed per car. Driver's side fitment.
From $95.03
Make a selection 96454303602 Necessary when replacing your right rear quarter window, as this seal retains the window in the body and prevents moisture from getting in. For 964 coupe models. Sold individually. 1 needed per car. Passenger's side fitment.
From $93.45
Make a selection 93110211100 High-quality OEM (original equipment manufacturer) fag replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Flywheel bushing located in the center of the flywheel at the rear of the crankshaft. View/Change Diagram
From $7.98
Make a selection FVD20798700 This FVD motorsports oil pump kit is a must for 987.1 Caymans and Boxsters driven on the track. Our kit includes a second return oil pump and our FVD motorsports oil pan. The issue: the 987.1 Boxster/Cayman from 2005 to 2008 has the factory return oil pump located on the right rear side. On the left side, the return oil pump located in front. So when driven fast in right turns, the oil from the camshaft case (rear left) does not flow back quickly enough into the oil pan. When the oil pan is starved of oil, the oil pump sucks in air and over time the motor will seize. The solution: our tandem return oil pump draws oil from the camshaft housing in (rear left, 3rd cylinder) and feeds it back into the oil pan so th...(choose a part on the right to read more)
$3,438.02
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |