PORSCHE 993 REAR LEDCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1994-98 - Engine (includes uncategorized and accessory items) 90151107321 This is the rear release cable for the rear engine deck lid. It is 1900 mm in length. When replacing this cable, we also recommend replacing the handle, part # 90155281320 and the grommet, part # 91151253100. Also, check your rear lid lower lock, part # 90151205200, perfect time to replace it if it is corroded and the spring is worn. Sold individually. 1 necessary per car.
From $9.50
Make a selection 90133300309B This rear spring plate is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New OEM spec. (65 shore) rubber bushings are installed to make this a direct bolt on. Features: made from ¼ inch spring steel includes new OEM spec. (65 shore) rubber bushings made in Germany sold individually. Left or right-side fitment. 2 necessary per car.
$306.90
Make a selection 911051 Porsche 911 ac compressor upgrade kit, 1984-89, lh drive model provides improved integrity with our kuehl barrier hose set, kuehl low- high pressure switch to help protect the system, a new denso factory compressor with clutch, new kuehl drier, complete o-ring kit, along with r134a charge port adapters. you can use either r12 or r134a with refrigerant with this complete kit. all barrier hoses match OEM configuration, have sae sae approved crimped fittings and each hose is labeled so you know where it goes.
$1,097.00
Make a selection 115900996BI01 Now you can enjoy the kind of precise suspension tuning formerly available only on race cars. The pss 10 suspension kit provides the ultimate in performance tuning. The fully adjustable monotube gas shock absorbers offer a selection of nine precise compression and rebound settings, from comfort to competition. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Handling and control are just a few twists away.
$3,855.50
Make a selection 115900996BI02 Now you can enjoy the kind of precise suspension tuning formerly available only on race cars. The pss 10 suspension kit provides the ultimate in performance tuning. The fully adjustable monotube gas shock absorbers offer a selection of nine precise compression and rebound settings, from comfort to competition. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Handling and control are just a few twists away.
$4,170.10
Make a selection 115900997BI Now you can enjoy the kind of precise suspension tuning formerly available only on race cars. The pss 9 suspension kit provides the ultimate in performance tuning. The fully adjustable monotube gas shock absorbers offer a selection of nine precise compression and rebound settings, from comfort to competition. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Handling and control are just a few twists away. *** these pss9's are for models without Porsche active suspension management***
$3,914.90
Make a selection 115900944018CS Sports suspension for 924 - 944 - 968 only for 18mm spring strut mounting this sports suspension is for everyday use and increase the dynamic and response. The lowering is adjustable (30-70mm front and 30-60mm rear). By using springs at the rear axle instead of torsion bars you improve extreme the handling of your car. By removing the rear torsion bars is the weight saving approximately 25kg.
$3,132.80
Make a selection 10050305503GFK Made in europe by one of the manufacturers to Porsche. Extremely high-quality grp (glass-reinforced plastic) rear bumper that includes every detail for a perfect fit. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight 9.7 lbs. (4.4 kg) - made of high strength, grp (glass-reinforced plastic) sold individually. 1 necessary per car. Please note: this only fits in conjunction with widebody / rsr rear fenders, part # FVD503930001 . Please provide us with the year / model. These are high quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world. All grp products must proper...(choose a part on the right to read more)
$1,265.00
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$218.90
Make a selection 100555100RSSC This is a rear lightweight carpet kit for a rs model or a rs tribute, without back seats. This set is made from German lightweight felt and does not include floormats. Features: genuine German lightweight felt trimmed in vinyl made in Germany custom made to order manufactured in Germany sold as a rear set. 1 necessary per car. Please note: when placing your order, we require the year, model and a list of any interior upgrades like roll bars, etc. This kit is custom made to order.
$940.50
Make a selection 11599702 Non pasm cars - lowers the front 1.0 inch (25 mm) and the rear 1.0 inch (25 mm). Pasm cars - lowers the front .8 inches (20 mm) and the rear .8 inches (20 mm). Targa - lowers the front 1.3 inches (35 mm) and the rear 1.3 inches (35 mm).
$470.80
Make a selection 150PB100922 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$44.00
Make a selection 150TBF900 Replace worn-out original front control arm / wishbone bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This is located at the front of the control arm / wishbone. The correct matching poly-graphite bushing for the rear of the control arm is part # 150tbr900 sold individually. 2 necessary per car.
$48.40
Make a selection 150PB100918 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$44.00
Make a selection FVD803993VR0222 High quality, German made three-point replacement safety belt, designed to perform like the original. Features / specs: belt length: 300 cm (118 inches) 3 point inertia reel belt angle adjustable reel (max. Of 8 *) includes 22 cm (8.5 inch) buckle, installation hardware and caps. Din-en-iso 9001: 2000 quality standard manufactured, e-mark approved. The matching rear belt is part # FVD803993hr sold individually. 2 necessary per car.
$187.00
Make a selection FVD803993VS0222 High quality, German made three-point replacement safety belt, designed to perform like the original. Features / specs: belt length: 300 cm (118 inches) 3 point inertia reel belt angle adjustable reel (max. Of 8 *) includes 22 cm (8.5 inch) buckle, installation hardware and caps. Din-en-iso 9001: 2000 quality standard manufactured, e-mark approved. The matching rear belt is part # FVD803993hr sold individually. 2 necessary per car.
$162.80
Make a selection FVDBS352911003 Make your next brake service a breeze with our pre-packaged service kits. Quality means everything to us, so we only source these parts directly in Germany. Kit contains: 1 qty. Oem set of rear pads (textar), part # 91135295005eq 2 qty. Oem brake warning sensors, part # 94461221105 sold as a set. 1 necessary per car.
$80.30
Make a selection 115993S1 Lowers the ride height by 30 mm (1.2 inches) in the front and 30 mm ( 1.2 inches) in the rear.
$663.30
Make a selection 91150411302EQ This one-piece seal is furthest from the rear bumper, we recommend replacing this when removing the motor for maintenance. We recommend replacing both the small and large engine seals, the large is part # 91150411102 sold individually. 1 necessary per car.
$16.50
Make a selection 91163195100EQ Don't let a cracked or faded lens detract from your cars appearance. Replace it with this high-quality OEM replacement, designed to perform like the original. This was genuine equipment on usa models but really cleans up the rear when added in place of the amber look. Quality replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Sold individually. Driver's side fitment. 1 necessary per car. Lookin...(choose a part on the right to read more)
$90.20
Make a selection 911561053003EQ Rear window cabrio top section, manufactured in Germany with original sonnenland material. It is as close to the original as possible and is cut and trimmed to fit perfectly. Sonnenland material consists of 3 layers, dyed acrylic twill weave top layer, elastomeric rubber inner layer and polyester woven base layer. It provides increased strength against abrasion, increased fade resistance and the tighter woven layers for the mechanically operated tops. Sonnenland high quality material was originally used by Porsche and other top German manufacturers. Made in Germany. Sold individually. 1 necessary per car.
$984.50
Make a selection 115993S Lowers the ride height by 35 mm (1.4 inches) in the front and 30 mm ( 1.3 inches) in the rear - like European m030. H&r sport springs are the ideal solution for the enthusiast who appreciates race-bred components designed for street use. Product benefits: sporty appearance improved handling characteristics lowered center of gravity linear or progressive spring design compatible with oe and aftermarket shock absorbers powder coated (purple) for anhanced appearance and corrosion resistance delivered with TUV approval engineered, manufactured and tested in Germany
$580.80
Make a selection 115900997BIT011 The pss 10 suspension kit provides the ultimate in performance tuning. The fully adjustable monotube gas shock absorbers offer a selection of nine precise compression and rebound settings. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Handling and control are just a few twists away. Regardless of whether in daily motoring, on the nordschleife of the nurburgring at the weekend, in training courses or in club sports - it's all pure driving enjoyment! Product advantages at a glance: • bilstein mono-tube/inverted technology • bilstein road tested and tuned • high driving dynamics with g...(choose a part on the right to read more)
$4,345.00
Make a selection 91150306203EQRB Without door post without rear lamp holder but: what you need for most quarter panel body repairs!
$1,654.40
Make a selection BES99126010S Our exhaust products are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredible value. Our entire "brombacher" line of exhausts is manufactured by m&m exhaust, gmbh in Germany who is no stranger to Porsche racing exhausts. Each is tested comprehensively for flow rate, thermal stress, resistance to cracking, and longevity. To further ensure quality, m&m use lightweight, motorsports grade, t 316 stainless steel material. Features: polished stainless steel double walled to dissipate heat so discoloration will take longer to appear / easier to polish out includes clamps for installation fits the factory cut outs in the bumper perfectly can be adjusted for...(choose a part on the right to read more)
$600.60
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |