PORSCHE 993 AXLESCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1989-94 - Front Axle/Steering (includes uncategorized and accessory items) BBI9964010006 Finally, a solution that allows you to safely increase without the risk of damaging your front axles. as you add GT3 shims to your front Porsche 996/997 turbo lower control arms, you move the cv joints beyond their safe range of motion, risking failure and expensive damage. These 10mm thick precision spacers, used with 16mm of lca shims will provide an additional -1.7 deg. Of camber, while maintaining the factory cv joint and axle relationship. the spacer design features a concentric lip that positively and accurately locates it to the cv joint for perfect balance and no vibration. Each kit includes two spacers and all the needed hardware in high class 10.9 grad
$375.00
Make a selection 91135295005EQ If your brake pads are at the end of their service life you will experience vibration, squealing, a pulsating brake pedal or poor response under heavy braking. We recommend replacing them as soon as any of the above signs are noticed. Also, be sure to inspect the rotors when changing the pads. For convenience, we sell complete rotor and pad kits, simply check under brake service kits. This pad set contains textar OEM (original equipment manufacturer) parts that we source in Germany to ensure quality, reliability and precise fitment. Textar brake pads are precision engineered to offer maximum safety, performance and comfort. This uncompromising approach has been the very ethos of textar for more than 100 years. ...(choose a part on the right to read more)
$73.70
Make a selection BK7033 Re-issue of autobooks manual covering engine, fuel & cooling systems, ignition, heating, exhaust emissions, clutch, transmission, rear axle, suspension, steering gear, brakes, electronics, and bodywork. This is a manual that will help keep 912 on the road. A must for any 912 owner. General FitmentACCESSORY
$32.00
Make a selection BBI9912020003 The bbi autosport 997 & 991 GT3 / rs exhaust side bypass is a direct replacement for the factory primary side mufflers. The primary mufflers are weigh approximately 44 pounds total while the bbi pipes are 4 pounds in comparison. For durability and protection against corrosion, each system is meticulously tig welded using 304 aerospace grade stainless tubing with lower carbon content. The result is a substantial reduction in weight behind the rear axle which significantly improves handling and less restriction to produce a much more aggressive exhaust note.
$950.00
Make a selection 24135299702YS High efficiency performance and race brake pads for track & street use. These are a high friction pad that are very resistant to heat and are fast to bed-in. Yellowstuff has been used with great success in both race and street cars. Yellowstuff is an aramid fiber-based brake compound with high brake effect even when cold. Yellowstuff is possibly one of the first ever compounds that can be used for street or track driving. These pads do not require warm up but do get even stronger under the heat of hard driving. These are not a low dust pad and if your desire is for a low dust premium street use pad, you should consider ebc redstuff. Features: made for up to 900*c (1,650*f). Developed for race cars but are stree...(choose a part on the right to read more)
$284.90
Make a selection 96433307301S We specify that the manufacturer use a 25% more stiff grade of rubber known in the industry as 85 shore. 85 shore refers to the rubbers density or hardness value. Oem is 65 shore and the factory European rs models use 85 shore; it suffers from less deflection, maintains more precise alignment and gives you the same repetitive feeling corner after corner. With aircooled 911's going up so much in value these days, we wanted to create suspension parts that look 100% oem, but also offer sportier handling without being too stiff for street use. They are manufactured in europe by an OEM supplier using the finest materials available (high carbon steel, 7075 t6 aluminum and 85 shore rubber). Upgrade yours today! Sold ...(choose a part on the right to read more) General Fitment911 1989-94
$159.50
Make a selection FVD33104381 The tow link is the furthest rear control arm on the rear axle. It is responsible for the toe angle adjustment. The OEM control arm bushings are simply too soft for track events and the teflon monoball racing bushings are too far too hard and noisy for street cars. Our sport bushings are made of a denser rubber (85 shore opposed to OEM 65 shore), which means that they are suitable for street and track use. Equally as important is that they do not produce any noise like the teflon bushings. FVD sport control arm facts: - better handling and more responsive. - makes precision adjustments of the suspension easier. - does not produce noise. - shore a hardness value of 85 for durability and handling. - fit's like o...(choose a part on the right to read more)
$451.96
Make a selection 96433307401R Looks 100 % OEM but is manufactured with a weather sealed monoball cartridge, for unparalleled suspension precision, sharper response and long lasting accurate alignment. These components are manufactured in europe by an OEM supplier and are meant for racing, clubsport and precision oriented street use. This manufacturer uses the finest materials available, like high carbon steel, 7075 t6 aluminum and spherical solid teflon lined bearings. Upgrade yours today! Sold individually. Right and left needed for the rear axle. Tech tip: washer and lock nut are included for easy installation. But now is the time to replace the old worn hardware as well. Below is a list of what is also suggested for installation. 1 qty. ...(choose a part on the right to read more) General Fitment911 1989-94
$302.50
Make a selection 24135299702RS Tired of having to wash the car just due to brake dust build up? Ebc redstuff brake pads have you covered. They reduce brake dust by 60-90%, plus the minimal dust is safely removed with a wet sponge as redstuff does not contain steel fiber particles found in other pads. These pads also have excellent brake friction when cold and just get better as they warm up. The pads are composed of a kevlar fiber-based brake compound enhanced with ceramic particles. The benefits of this material are longevity, enhanced braking performance, quiet operation and reduced brake dust. Features: made for up to 750*c (1,382*f) for street, track and rally use. Low dust, high performance street pad with 20-25% braking improvement. Ca...(choose a part on the right to read more)
$269.50
Make a selection BBI9964010004 Features
$795.00
Make a selection 240911352HBH Pagid light blue rsh29e are from the rsh line of historic racing brake pads. They are a medium to high friction coefficient racing compound that requires less pedal effort during racing. Rsh29e pads provide constant friction levels over a wide range of operating temperatures. They offer lower disc wear rates and long pad life. Applications include: historic endurance racing, historic GT racing and historic touring car racing. Features at a glance: medium to high friction coefficient very good thermal stability low pedal effort slightly progressive in-stop behavior and good modulation long pad and disc life pagid is one of the leading manufacturers of racing brake pads and is successful at the world's most dema...(choose a part on the right to read more)
$299.20
Make a selection 115110015 Lower your ride height up to 1.5 inches (40mm) by simply replacing the spring plate. This spring plate set the spring 1.5 inch lower. Factory shock and spring can be used. This leaves the damping and spring characteristics original even the car is lowered. Please note: only for shocks with a diameter of 61.85 mm at the threads. This will not fit mo30 suspension (i.e. Shock part #'s 965 343 041 05 / 965 343 042 05). This cannot be used on bistein b6 and hd shocks. Sold individually! 2 required for the front axle. General Fitment911 1994-98911 1989-94
From $75.90
Make a selection 240996352RSL1 Pagid yellow rsl1 are from the rsl line of endurance racing brake pads. They are a high friction coefficient racing compound with long pad and disc life, and are easily bedded in. Rsl1 pads are manufactured of a low metallic resin bonded material containing steel and acrylic fibers. They operate in a wide operating temperature range and have good friction stability vs. Temperature. Applications include: GT cars, touring cars, prototype racing and in spring racing. Features at a glance: high friction coefficient high bite high fade resistance high pad and disc life high modulation pagid is one of the leading manufacturers of racing brake pads and is successful at the world's most demanding racetracks. They offe...(choose a part on the right to read more)
$512.60
Make a selection 240991352GS Pagid yellow rsl 29 are from the rsl line of endurance racing brake pads. They are a medium friction coefficient racing compound with long pad and disc life, and are easily bedded in. Rsl 29 pads are manufactured of a low metallic resin bonded material containing steel and acrylic fibers. They operate in a wide operating temperature range and offer excellent release characteristics. Rsl29 pads offer low heat conductivity and work well with abs systems. They offer excellent modulation and controllability. They offer lower disc wear rates and are fade resistant up to a temperature of 650*c (1,202*f). Applications include: club racing, track days, touring cars, prototype endurance racing and GT cars. Features at a...(choose a part on the right to read more)
$654.50
Make a selection 11595B00HR Lowering up 40mm, front axle load 1290kg / 1340kg rear
$614.90
Make a selection 115965 H&r sport springs lower the vehicle center of gravity and reduce body roll for better handling. Enhance the look of your vehicle with a reduced fender well gap. The progressive spring rate design provides superb ride quality and comfort. A lower wind resistance signature will make the vehicle more streamlined and improve gas mileage. Benefits: lowers the front axle 1.5 inches (35mm) and the rear axle 1.5 inch (35mm). Sporty appearance improved handling characteristics lowered center of gravity linear or progressive spring design compatible with oe and aftermarket shock absorbers powder coated (red) for enhanced appearance and corrosion resistance delivered with TUV approval engineered, manufactured and tested i...(choose a part on the right to read more) General Fitment911 1989-94
From $645.62
Make a selection 99160918100 When your pads reach a critical level, these sensors will trigger a warning to alert you that your pads need to be changed. Be sure to purchase these in conjunction with your new brake pads. High-quality OEM replacement designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per axle.
From $12.10
Make a selection 115964HR H&r sport springs lower the vehicle center of gravity and reduce body roll for better handling. Enhance the look of your vehicle with a reduced fender well gap. The progressive spring rate design provides superb ride quality and comfort. A lower wind resistance signature will make the vehicle more streamlined and improve gas mileage. Benefits: lowers the front axle 1.5 inches (38mm) and the rear axle 1.3 inch (33mm). Sporty appearance improved handling characteristics lowered center of gravity linear or progressive spring design compatible with oe and aftermarket shock absorbers powder coated (blue) for enhanced appearance and corrosion resistance delivered with TUV approval engineered, manufactured and tested ...(choose a part on the right to read more) General Fitment911 1989-94
From $494.69
Make a selection 115964E The eibach pro-kit dramatically improves both a vehicle's performance and appearance. It precisely lowers your car's center of gravity, reducing squat during acceleration, body roll in corners and excessive nose-dive under braking. Pro-kit also reduces excessive fender-well clearance, making your car look just as good as it performs. Benefits: lowers the front axle 1.3 inches (30-40mm) and the rear axle 1 inch (35mm). High performance handling and aggressive good looks lower center of gravity stop quicker, corner faster and get better mpg!* progressive spring design for excellent ride quality * improves your aerodynamic efficiency by forcing more air over the car and less underneath (where most of the drag is...(choose a part on the right to read more) General Fitment911 1989-94
From $293.45
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |