Vehicles
Sections
215 not categorized PORSCHE 993 BUSHISCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1987-89 (includes uncategorized and accessory items) FVD33150005 Restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm cannot compensate enough when lowering your Porsche, leaving you with as much as ½ inch of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration. Sold in pairs. 1 necessary per car.
$802.73
Make a selection FVD205993001HA H&r rear sway bar with a 24 mm diameter. 2-way adjustable. This is the rear sway bar from our kit, part # FVD205993001. Includes bushings. Sold individually. 1 needed per car.
$421.58
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$229.85
Make a selection ER2011000 Monoballs deliver precise, razor sharp handling. but rapid wear has made them impractical for all but the most serious racers. Not anymore! Weather seals - our proprietary-design monoball cartridges have weather seals to keep dirt out and extend product life. this is the only monoball suitable for street or extended track use. dirt and water contaminate ordinary products and accelerate wear. Performance - today’s sticky tire compounds generate corner loads that easily compress factory rubber bushings causing wandering alignment settings. Camber and toe flop around upredictably. weather-sealed monoball cartridges replace compliant factory rubber bushings with hardened-steel spherical bearings. Unlike...(choose a part on the right to read more) General Fitment914 1970-76911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1965-69 912 1965-69
$314.95
Make a selection FVD34101702ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$438.90
Make a selection ER2051500 High performance bushing replacement, no squeaks! Want to experience precision driving, faster lap times, improved road feel and feedback? These patented elephant racing polybronze suspension bearings set a new standard for performance, ride quality and ease-of -installation. Polybronze have a rigid bronze bearing core that does not deform. The polyurethane jacket absorbs mount irregularities while the bronze inner bearing remains true, providing a free-moving machined-fit that rides on a precision race. provided grease fittings make re-lubrication a breeze and a figure 8 groove keeps grease in place. The combination delivers zero squeaks and friction-free suspension movement. well suited to street or track, ...(choose a part on the right to read more) General Fitment911 1965-69912 1965-69 914 1970-76 911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89
$302.40
Make a selection 91442422400 This is a high-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. View/Change Diagram
From $3.61
Make a selection 99333105280 The bushings are made of rubber with an 85-shore hardness value, which is more durable, provides more positive suspension location and is still quiet and comfortable for street use. Sold individually.
From $802.73
Make a selection 99333104503ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install the bushings. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for its return to you. We do not offer a core exchange on this part.
$266.81
Make a selection 40032I These 4340 chromoly steel i-beam connecting rods are made to the tightest tolerences exclusively for your Porsche. Fully machined billet, (not forged), these are surface peened hardened, cryogenically treated, and balanced within a gram. They come complete with aerospace-quality arp 2000 fasteners and ampco 45™ bushings. When only the best will do, these rods are built to the extreme. General Fitment930 1975-77911 1984-86 911 1987-89
$1,905.75
Make a selection 90133300309B This rear spring plate is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New OEM spec. (65 shore) rubber bushings are installed to make this a direct bolt on. Features: made from ¼ inch spring steel includes new OEM spec. (65 shore) rubber bushings made in Germany sold individually. Left or right-side fitment. 2 necessary per car.
$322.25
Make a selection 91110190160EQ Oem (original equipment manufacturer) complete set of bearings (including # 8) sourced in Germany to ensure quality, reliability and precise fitment. Set includes: 1 qty. Crankshaft main bushing sleeve - bushing viii - oversize +0.25mm 12 qty. Crankshaft main bearing shells ii-vii (half) - oversize +0.25mm 2 qty. Crankshaft main bearing shells i (half) - oversize +0.25mm sold as a set. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.
$726.65
Make a selection 90030900300 This is the roll pin that secures the shift lever to the shift shaft inside the shift console on all 73-76 914s it is necessary to replace this whenever replacing the shift shaft seal. look at the crown and cup bushing at the same time and replace if necessary View/Change Diagram
From $2.08
Make a selection 96437504381 Replace your worn-out, original soft rubber engine mounts with our higher density, rs specification rubber bushing. This is manufactured of rubber with a 75-shore hardness value. 75-shore is the same density as what is used in the rs models. It is more durable, provides more positive, sharper shifts and offers crisper throttle response. Yet, rs spec rubber is still quiet and comfortable for street use. Features: sharper shifts crisper throttle response does not produce nvh (noise vibration harshness) like teflon or solid bushings rubber has a shore hardness value of 75 (like rs models) made in Germany this mount is a high-quality OEM (original equipment manufacturer) replacement part, designed to perform like t...(choose a part on the right to read more)
From $199.99
Make a selection 96434101807AT By ordering this article number, you will receive a reconditioned wishbone with newly pressed-in bearings. The calculated replacement deposit will be returned to you as soon as the old part has been received and checked. This item is also available with race bearings (85 shore).article number FVD 341 018 07at the reconditioning process includes full inspection of each track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. If your old part is not repairable we will inform y...(choose a part on the right to read more)
$438.90
Make a selection 96433102200RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$705.71
Make a selection 96434307181ATK Looking for a more cost-effective solution than ordering a new link? Let us recondition your original drop link. The reconditioning process includes full inspection, disassembly, degreasing and media blasting. Once fully prepared, we properly install new bushings, finish with a corrosion proof coating and include a new lock nut. Please note: each link is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your link we will notify you as soon as we can. Arrangements can be made for its return to you. Sold individually. 1 necessary per car.
$204.44
Make a selection 91142402404 Does your car have a broken or stripped shift coupler? a brand new coupler is the answer to your issues. if you have issues shifting into gear or catching the correct gear, try a new coupler. This is for a 911. Can also be used for a 914 by removing the black portion. View/Change Diagram
From $116.55
Make a selection 91434701006 Quality new replacement steering rack manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment manufacturers (oem) to Porsche in Germany. Includes: - steering joint bushings - bellows retainers - outer retaining spring - bellows - inner retaining spring - steering rack coupler disc - steering rack coupler disc lock plate sold individually. 1 necessary per car. View/Change Diagram
From $416.59
Make a selection 911FDLNK Upgrade your stock front swaybar with this simple bolt in replacement for the factory drop links.
$215.25
Make a selection FVD10099902 With the roll bar camera mount and your video camera, you can have it all. 3-axis adjustment lets you capture any view - study strategies, document infractions, refine your technique, even tape yourself as you drive. Special vibration-absorbing urethane bushings assure a clear picture. No drilling required easy installation. Security strap included. General FitmentALL
From $165.84
Make a selection 229485 Forged from the highest quality steel, each torsion bar is centerlessly ground to provide a constant spring rate, chemically coated to protect against rust and then matched in pair sets to ensure that both sides of the car are equally suspended. All weltmeister torsion bars are guaranteed for 3 years against breakage. General Fitment911 1987-89
$537.60
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |