Vehicles
Sections
308 not categorized PORSCHE BOXSTER TIRESCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1987-89 (includes uncategorized and accessory items) FVD33150005 Restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm cannot compensate enough when lowering your Porsche, leaving you with as much as ½ inch of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration. Sold in pairs. 1 necessary per car.
$764.50
Make a selection CUPAHOLDER Designed to hold most cups, glasses, and water bottles for the 1974 to 1994 Porsche 911 with standard door pockets. It works in both door pockets with no mounting or modifications necessary. Also includes a pen, pencil and air gauge holder. General Fitment911 1978-83911 1984-86 911 1987-89 911 1989-94 911 1974-77 930 1975-77
$70.88
Make a selection FPOR4300 They started from scratch to offer a complete high performance exhaust system for the Porsche 911. Extensive dyno testing on their in-house dynamometer afforded impressive horsepower and torque gains throughout the entire power band. Muffler are meticulously built by hand using t304 stainless steel for a lifetime of performance - guaranteed! Billy boat performance exhaust has a deep commitment to build quality products. With over 3 generations of fabrication and racing experience going into the development of every part that b&b makes, along with the use of only the finest t304 stainless steel materials, it is easy to see why b&b has been an industry leader for over 20 years. B&b designs every system for increa...(choose a part on the right to read more) General Fitment911 1984-86911 1987-89
From $1,313.70
Make a selection ER2081500 Need more camber?elephant racing de-cambered ball joints provide up to 3/4 degree additional negative camber per side. track is widened up to 1/2 inch. The ball joint stud is non-concentric with the housing, effectively lengthening the control arm and pushing the bottom of the strut (and tire) out resulting in added negative camber. Construction includes a true spherical bearing monoball for low-friction, freedom of movement and zero deflection. fully weather-sealed, de-cambered ball joints are a true bolt-in using factory ball joint hardware. General Fitment911 1970-73911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89 914 1970-76
$493.50
Make a selection BRAID168RSR New to the usa from spain, braid wheels offer a full range of competition wheels for tarmac rally, gravel rally, snow, track, rally cross, hill climbing, rally-raid, kart and classic cars. Monoblock wheels are specifically designed for competition, are cast from lightweight aluminum and heat treated for maximum strength. Complete with steel bolt inserts to prevent wear and hub-centric to your specific model so no hub rings are required. We are pleased and excited to make these excellent wheels available for the first time in the usa. General Fitment912 1965-69914 1970-76 924 1980-85 924 1986-88 944 1982-85 944 1985-88 944 1989-91 911 1965-69 911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89
$1,015.35
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$218.90
Make a selection BRAID169RSR New to the usa from spain, braid wheels offer a full range of competition wheels for tarmac rally, gravel rally, snow, track, rally cross, hill climbing, rally-raid, kart and classic cars. Monoblock wheels are specifically designed for competition, are cast from lightweight aluminum and heat treated for maximum strength. Complete with steel bolt inserts to prevent wear and hub-centric to your specific model so no hub rings are required. We are pleased and excited to make these excellent wheels available for the first time in the usa. General Fitment912 1965-69914 1970-76 924 1980-85 924 1986-88 944 1982-85 944 1985-88 944 1989-91 911 1965-69 911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89
$1,208.55
Make a selection BRAID1510 New to the usa from spain, braid wheels offer a full range of competition wheels for tarmac rally, gravel rally, snow, track, rally cross, hill climbing, rally-raid, kart and classic cars. Monoblock wheels are specifically designed for competition, are cast from lightweight aluminum and heat treated for maximum strength. Complete with steel bolt inserts to prevent wear and hub-centric to your specific model so no hub rings are required. We are pleased and excited to make these excellent wheels available for the first time in the usa. General Fitment912 1965-69914 1970-76 924 1980-85 924 1986-88 944 1982-85 944 1985-88 944 1989-91 911 1965-69 911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89
$876.75
Make a selection 10050330000 This 9 inch front and 11 inch rear steel fender flare set is made in Germany, we offer a complete line of replacement bodywork to complement the entire Porsche model range. Sold individually. 1 necessary per car. Please note: for conversions, these flares will allow you to run 9 wide tires in the front and 11 wide in the rear. For the 964 / 965 models the torsion bar cut out must be filled. Due to variances in production at the factory, age, accident damage or rust, each part may require trimming and or adjustment for perfect fitment.
$1,648.90
Make a selection 170211025SS This is a high-quality replacement for original number, 930 211 025 01 manufactured by dansk. It is manufactured in stainless steel. Dansk offers a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For a proper installation, we recommend heat exchanger installation kit, part # FVDmk911102 sold individually. Right or left side fitment. 2 necessary per car. Please note: this will not fit u.s. 3.0 l SC models from 1980-83. We suggest our part # 100 2...(choose a part on the right to read more)
$1,091.20
Make a selection 170211033SS This is a high-quality replacement heat exchanger manufactured by dansk. It is manufactured in stainless steel. Dansk offers a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For a proper installation, we recommend heat exchanger installation kit, part # FVDmk930100 sold individually. Right or left side fitment. 2 necessary per car.
$1,147.30
Make a selection 1002110211DA This is a high-quality replacement for original number, 911 211 021 60 manufactured by dansk. It is manufactured in stainless steel and includes the necessary brackets and tabs for a direct bolt on replacement. Dansk offers a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For a proper installation, we recommend heat exchanger installation kit, part # FVDmk911100 sold individually. 1 necessary per car. Please note: the corresponding right side i...(choose a part on the right to read more)
$1,348.60
Make a selection 00004400022 Hold 4 wheels with tires and the hardtop. Rolls on casters for easy storage. Storage bins on either side to hold snow chains or car care products. Top and cover not included. General FitmentACCESSORY
$724.71
Make a selection 220110901ATK Sport throttle bodies are a great addition for those with highly modified cars. They are a great addition for those with full exhaust systems (larger diameters), maf kits, larger displacements, street or race cams, etc. The remanufacturing process includes full inspection of your throttle body to ensure proper operation after the remanufacturing process. We then disassemble and bore the original to a 2.8-inch (71 mm) diameter. The entire throttle body is cleaned, degreased and the internals are polished to create more laminar flow. We then machine the shaft to accept larger butterfly's which seamlessly match the bore. All clearances are checked for precision to ensure reliability. Each throttle body is remanuf...(choose a part on the right to read more)
$485.10
Make a selection 1002110221DA This is a high-quality replacement for original number, 911 211 022 10 manufactured by dansk. It is manufactured in stainless steel and includes the necessary brackets and tabs for a direct bolt on replacement. Dansk offers a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For a proper installation, we recommend heat exchanger installation kit, part # FVDmk911100 sold individually. 1 necessary per car.
$1,348.60
Make a selection 17092102S This cross over connector replaces original part # 930 111 157 01, it is a quality stainless steel replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For proper installation, we recommend a new exhaust gasket, part # 93011119307 and sealing ring, part # 91111118903 sold individually. 1 necessary per car.
$82.50
Make a selection 170211014 This steel heat control box is a quality replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For proper installation, we recommend a new exhaust gasket, part # 91121129700 clamp, part # 90121105222 and connecting piece, part # 91165911900 sold individually. 1 necessary per car.
$148.50
Make a selection 12837018R Stoptech recognizes that great brakes need to look as good as they perform. Performance wheels and tires are best complemented with stoptech sportstop cross-drilled or drilled+slotted rotors.every sportstop brake rotor is produced from a high quality centric parts blank casting and finished in a durable e-coating for corrosion resistance. Sportstop drilled and slotted brake rotors (prefix 127) prevent glazing of the pads, add bite and improve wet and dry braking performance.every sportstop rotor is finished with black e-coating on both sides of the hat, inside the the cooling vanes, and on the outside edge. E-coating is a superior electro-statically applied finish designed to withstand 400 hours of salt water e...(choose a part on the right to read more) General Fitment911 1984-86911 1987-89 911 1989-94
$111.91
Make a selection 170211016 This stainless-steel heat control box is a quality replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For proper installation, we recommend a new exhaust gasket, part # 91121129700 clamp, part # 90121105222 and connecting piece, part # 91165911900ssi sold individually. 1 necessary per car.
$179.30
Make a selection 22011090102ATK Sport throttle bodies are a great addition for those with highly modified cars. They are a great addition for those with full exhaust systems (larger diameters), maf kits, larger displacements, street or race cams, etc. The remanufacturing process includes full inspection of your throttle body to ensure proper operation after the remanufacturing process. We then disassemble and bore the original to a 2.7-inch (70.5 mm) diameter. The entire throttle body is cleaned, degreased and the internals are polished to create more laminar flow. We then machine the shaft to accept larger butterfly's which seamlessly match the bore. All clearances are checked for precision to ensure reliability. Each throttle body is reman...(choose a part on the right to read more)
$589.60
Make a selection 199801 These aluminum flywheels are made from the highest quality 6061 t6 aluminum, fantastic for strength, heat dissipation and of course reduction in weight. for the friction surface they use 1045 steel and attach a replaceable friction surface with military grade aerospace fasteners. with these replaceable friction plates there is no need to replace the entire flywheel when the clutch or flywheel is at the end of it’s life, saving time and money. the ring gears are made from 1050 steel and are heat treated for durability. the flywheel ring gears are heated then pressed on and secured with grade 8 button screws. fidanza flywheels are engineered to perform. General Fitment911 1984-86911 1987-89
$771.48
Make a selection 170211021 This is a high-quality replacement for original number, 911 211 021 60 manufactured by dansk. It is manufactured in steel and includes a corrosion resistant protective coating. Dansk offers a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For a proper installation, we recommend heat exchanger installation kit, part # FVDmk911100 sold individually. 1 necessary per car. Please note: the corresponding right side is our part # 170211022
$1,092.30
Make a selection 12837019R Stoptech recognizes that great brakes need to look as good as they perform. Performance wheels and tires are best complemented with stoptech sportstop cross-drilled or drilled+slotted rotors.every sportstop brake rotor is produced from a high quality centric parts blank casting and finished in a durable e-coating for corrosion resistance. Sportstop drilled and slotted brake rotors (prefix 127) prevent glazing of the pads, add bite and improve wet and dry braking performance.every sportstop rotor is finished with black e-coating on both sides of the hat, inside the the cooling vanes, and on the outside edge. E-coating is a superior electro-statically applied finish designed to withstand 400 hours of salt water e...(choose a part on the right to read more) General Fitment911 1984-86911 1987-89 911 1989-94
$279.44
Make a selection 10021103000 This heat exchanger is engineered for the discerning Porsche 911 3.2 l owner looking for more performance. These are manufactured in stainless steel by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Features: gains of +10 hp and +10-15 tq stainless steel 1.5" pipe diameter for backpressure reduction 21.5 mm thick flange with "fire ring" connects "early style" dual inlet mufflers bolt on replacement for the right side re...(choose a part on the right to read more)
$1,772.10
Make a selection BES99107060S The perfect addition for an aggressive exhaust note with the added benefit of reduced weight. Features: 2 1/2 (63.5mm) tubing. Weighs 8.3 lbs. (3,7 kg), 10 + lbs. Savings over stock GT3 center muffler. Made of German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. Fits 991.1 and 991.2 GT3 & GT3 rs models.- reuse's factory tips. Includes all necessary clamps and mounting brackets. Made in Germany by m&m exhaust, gmbh. Intoxicating growl at idle, partial throttle and wide-open throttle. No interior resonance or drone. Ecu software is not necessary. Does not alter emissions, 50 state legal in the u.s. Our entire "brombacher" line of exhausts is manufactured by m&m exhaust, gmbh in Germany. T...(choose a part on the right to read more)
$2,313.30
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |