![](https://30ed524141d0cac60ab4-d2e2d18a14257de3b9ce428cf077ee97.ssl.cf2.rackcdn.com/acban.jpg)
PORSCHE 997 TURBO EARCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1987-89 - Front Axle/Steering (includes uncategorized and accessory items) ![]() 99312301352ATK Our k-16 remanufactured turbo is cost competitive and is a direct replacement. Simply send us your original k16 turbochargers and a borg warner / kkk certified technician will remanufacture your turbo. The remanufacturing process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will replace the turbine wheels, thrust bearings, install new seals, install new waste gates, recondition the internals and high speed balance the turbo. This ensures reliability and superior performance for many years to come. The remanufacturing is done on an exchange basis only. You must send us your original k16 turboc...(choose a part on the right to read more)
$2,194.50
Make a selection BK1081 Michael cotton captures the complete evolution of Porsche’s “turning point " from vw research and development, to Porsche’s adoption and on, the 944 turbo. The hardbound book has 128 pages of great and advice on your four cylinder liquid-cooled Porsches. General FitmentACCESSORY924 1976-79 924 1980-85 924 1986-88 944 1982-85 944 1985-88 944 1989-91 968 1992-95
$34.94
Make a selection BES99125010SK Are you one of those that are looking for more sound from your Porsche sport exhaust (pse)? Perhaps it's not quite as aggressive as you would like, or your last Porsche just sounded so much better? Don't worry, we have you covered, and the beauty is, you don't have to touch the catalytic converters which is a big no, no with Porsche dealers. With the valves open you receive a far more exotic, rich, deep, turbo motorsport tone and with the valves closed, soft subtle, completely stock sounds. So, absolutely no compromise and you will be thinking, the car really should have left the factory like this! Features: - + 10 crank hp & + 8 crank torque. - weighs 29 lbs. (13 kg) - German v2a - x5crni18-10 - 1.4301 stai...(choose a part on the right to read more)
$4,832.30
Make a selection FVD95761890MG Factory: engine - v8 twin-turbo capacity - 4806ccm compression ratio - 10,5:1 max. Power - 368kw (500hp) @ 6000rpm max. Torque - 700nm (516 lbf ft) @ 2250-4500rpm max. Speed - 275km/h max. Rpm - 6500rpm acceleration 0-100km/h - 5.1s tuning:* max. Power - 397kw (540hp) @ 6000rpm max. Torque - 780nm (575 lbf ft) @ 3500rpm max. Speed - 280km/h max. Rpm - 6700rpm acceleration 0-100km/h - 5.0s * only with sport exhaust system and sport air filter for 27 + years, FVD-Brombacherhas been setting the standard for Porsche engine building and tuning in Germany. Our deep understanding of the flat 6 Porsche engine naturally led to our engine management software. Over the years we have perfected the art of software tuning, ...(choose a part on the right to read more)
$1,094.50
Make a selection 93012321001 Turbocharger wastegate membrane diaphram
$220.00
Make a selection FVD123041ATK FVD Brombacher997.1 tt "700 series" upgraded turbos facts: - cnc re-profiled compressor housing and backing plate - new, lightened and larger compressor wheel (12 blades) - reworked turbine wheel, lightened and optimized for higher flow and reduced backpressure. - all new bearings. - all new piston rings and seals. - all parts cleaned, inspected and measured to motorsport specifications. - all parts are balanced (static & dynamic) up to 120.000 rpm with balancing protocol. - 47.55 mm inducer - 66 mm exducer - flow rate = 37 lbs. / minute or 280g/s - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already runn...(choose a part on the right to read more)
$2,854.50
Make a selection FVD50599102MM The moshammer evo 2 front chin spoiler blends a bit of Porsche heritage into its design with canard style winglets. This effective design transforms turbulent air into a more laminar flow, creating added downforce. Porsche active aerodynamics remains fully functional in all 3 positions and the evo 2 chin spoiler secures seamlessly into the factory locations. The evo 2 spoiler's design offers a more aggressive look but also blends perfectly with other design elements like the side skirts and rear spoiler. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of either the evo rs (991.2 turbo/s) or downforce rs...(choose a part on the right to read more)
$1,386.00
Make a selection FVD123020ATK Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)
$2,042.70
Make a selection FVD10397501CARR Connecting rod with plc carr-6 screw. The s connecting screw (plc carr-6) needs only every third time to be changed under race conditions or motor sport use when overhauling the engine. When used in 997.1turbo connecting rod bearing 99310314715set must be used (tongue / nose opposite). Carrillo is one of the most respected connecting rod manufacturers in competitive motor sports. Carrillo rods are constructed from their propriety alloy and forged to their custom specifications. The rods are then fully machined to guarantee the removal of all surface imperfections. After heat treatment, each connecting rod is magnaflux inspected and hardness checked, then machined to final size. Each set is balanced and then sho...(choose a part on the right to read more)
$2,952.40
Make a selection FVD3522946993R Genuine rear "big red" brake kit which includes 993 turbo calipers, discs, pads, damping plates, warning contacts and hex head mounting bolts. Please note: this kit requires you to reuse your original emergency brake and dust shield.
$3,681.37
Make a selection FVD351997TTCS This kit convert's the 997 turbo pccb rotors to steel rotors with yellow pagid pads.( only 5-hole, not central lock ) this system is complete with everything that you need to install. Do not ruin your expensive ceramic brake discs on the track. Get ready for racing with the original and much cheaper Porsche motorsport steel brake discs! What's in the box: 4 x 2-piece brake discs (380 x 34 mm - front / 350 x 28 mm - rear) 4 x wear sensors 2 x set ( front and rear ) brake pad set (pagid yellow - rs29 ) 8 x screws for brake caliper 8 x damping plates technical tip: also order stainless steel brake lines (FVD b96 355 97) and racebrake fluid (012 145 ca).
$6,344.80
Make a selection FVD95761891MG Genuine: engine - v8 capacity - 4806 ccm compression ratio - 12,5:1 max. Power - 298kw (405hp) @ 6500rpm max. Torque - 500nm @ 3500rpm max. Speed - 253km/h max. Rpm - 7000rpm acceleration 0-100km/h - 6,1s tuning: max. Power - 312kw (425hp) @ 6000rpm max. Torque - 520nm @ 4500rpm max. Speed - 265km/h max. Rpm - 7200rpm acceleration 0-100km/h - 5,7s for 27 + years, FVD-Brombacherhas been setting the standard for Porsche engine building and tuning in Germany. Our deep understanding of the flat 6 Porsche engine naturally led to our engine management software. Over the years we have perfected the art of software tuning, making substantial gains in horsepower and torque, while retaining drivability and most importan...(choose a part on the right to read more)
$1,094.50
Make a selection FSPOR992SC Purchase disclaimer: fabspeed motorsport does not condone the use of emission defeat devices for any vehicles used on public streets or roadways. Fabspeed motorsport will not tamper, remove, disable, or bypass emissions equipment on a motor vehicle in accordance with 40 cfr section 86.1854.12(a)(3), clean air act 40 cfr 1068.101(b). This includes software, known as tunes, that reprogram a motor vehicles electronic control module to alter engine performance and enable the removal of filters, catalysts, and other critical emissions controls.
$3,695.95
Make a selection GR2009 This product reduces friction and guarantees energy-conserving performance for the unit. This yields the following advantages: significant savings in fuel and oil consumption, scientifically proved reduction in wear, fewer breakdowns, emergency lubrication properties. Tested on catalytic converters and turbochargers. You may also notice a modest increase in horsepower, and lower fuel and oil consumption. General FitmentACCESSORY
$11.43
Make a selection FVD98010001 Kit includes: 2 x sport motronic dme (ecu) exchange 2 x sport airfilter genuine: engine - v10 cylinder capacity - 5733ccm compression ratio - 12,0:1 max. Power - 450kw (612hp) @ 8000rpm max. Torque - 590nm @ 5750rpm max. Speed - 330km/h max. Rpm - 8400rpm acceleration 0-100km/h - 3.9s tuning: max. Power - 478kw (650hp) @ 8000rpm max. Torque - 640nm @ 6000rpm max. Speed - 340km/h max. Rpm - 8600rpm acceleration 0-100km/h - 3.8s our Carrera GT ecu programming offers you not only more power and torque but phenomenal sound! Within the cgt end muffler is a flap-type mechanism fitted which is controlled by vacuum units. These vacuum units are also controlled by the ecu. Our programming modifies the control of these f...(choose a part on the right to read more)
$7,594.36
Make a selection FVD11401214 Hailing from the baden wurttemberg region in Germany, speaking the language and dealing with lead engineers from the OEM and motor sport manufacturers for more than 30+ years has many advantages. We are able to source this flywheel from an elite German motorsports manufacturer who delivers the highest quality available. Features: quicker acceleration 9 bolt scalloped design precision machined billet steel computer balanced made in Germany replacement for original number 93010220201 sold individually. 1 necessary per car. Please note: this only fits 930 turbo models from 1978-79.
$526.90
Make a selection WAPC2400217 Porsche pedal car in Cayenne turbo design with precision chain drive. Closely based on the original with many typical features including headlights, taillights, and tailpipes. Spacious interior. Painted steel chassis with plastic body. Tested by German safety standards agency (tÃœv). Suitable for ages 3-5 years. Silver. Dimensions: 47 x 22 x 20.5 in. (119 x 56 x 52 cm) General FitmentACCESSORY
$268.52
Make a selection FVD123013 K-16/24 turbo (up to 555 hp) power is focused on low and mid-range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD Brombacher993 k-16/24 new turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The process starts with re-profiling the OEM turbocharger compressor housing and m...(choose a part on the right to read more)
$2,976.60
Make a selection FVD123013ATK K-16/24 turbo (up to 555 hp) power is focused on low and mid range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD brombachers 993 k-16/24 remanufactured turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The remanufacturing process starts with re-profiling the OEM turbochar...(choose a part on the right to read more)
$2,976.60
Make a selection FVD51299701MM Rear diffuser for all Porsche 997.1 Carrera models. The mounting is very easy. Plug & play with 3M double tape and 2 screws on the screwing points. Not for models with the turbo | GT2 | GT3 rear bumper
$1,312.30
Make a selection 90134775300 Known as: shear bolt View/Change Diagram
From $10.70
Make a selection STB90P2 This kit was designed to efficiently remove and install the wheel bearing and hub of spindle assemblies. Built-in self centering mechanism and incorporates a roller thrust bearing which lines up straight as an arrow during removal and reinstallation. These kits have a 20 year service history at thousands of repair shops. Every kit comes with a detailed instruction manual and does not require a hydraulic press. These kits are specific to the Porsche models listed. General Fitment911 1989-94911 1994-98 911 1974-77 911 1978-83 911 1984-86 911 1987-89 944 1985-88 944 1989-91 968 1992-95 924 1986-88 BOXSTER 1997-04
$510.47
Make a selection FVDBSK35299701S Brake service kit contains: - brakediscs - brake-pads ( pagid yellow ) - warning contact's - caliper screws - damping plates only for cars without central-lock.
$1,290.30
Make a selection FVDBS352996003 Brake service kit contains: - brake-pads - warning contact's - damping plate's ( anti-squel shims )
$884.40
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |