PORSCHE 356 B REAR BUSHINGCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1987-89 - Electrical (includes uncategorized and accessory items) FVD33105900 Replace worn-out rear trailing arm bushings with our FVD sport bushings, made of rubber with an 85 shore hardness value that is the same as the rs models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. This is a direct replacement for original part # 90133105900 features: better handling makes precision adjustments of the suspension easier does not produce any noise like the teflon bushings. Rubber has a shore hardness value of 85 (like rs models) fit's like oem, simple installation made in Germany set is sold per axle. 1 necessary per car.
$166.32
Make a selection FVD33150045R Replace worn-out soft rubber (65 shore hardness value) control arm bushings (camber link and caster link) with sportier rubber (75 shore hardness value) that is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing cartridge is weather sealed and is crafted in high carbon steel and 7075 t6 aircraft aluminum. Sold individually.
$74.84
Make a selection FVD33150045 Original rubber replacement bushing (65 shore hardness value) for the rear control arms (camber link and caster link). This bushing cartridge is weather sealed and is crafted in high carbon steel and 7075 t6 aircraft aluminum. Sold individually.
$70.09
Make a selection FVD33150001 Solid bushings and mounts allow you to achieve exact suspension articulation which improves handling and stability on lowered / race prepared cars. The original soft rubber bushings can deform under track loads which allows the sub frame to shift and throw the camber and toe off. Solid bushings will not deform and will keep the camber and toe settings in line which equates to confidence in cornering and faster lap times. These are intended to replace the soft rubber bushings on the original rear sub frame (part #'s 993 331 051 00 & 993 331 052 00). They are made in Germany and are TUV approved. Sold as a set. 1 set is necessary per car. Please note: if you are also driving your car on the street, they will res...(choose a part on the right to read more)
$262.55
Make a selection FVD33150046 Replace worn-out original soft rubber track rod bushings with these OEM replacements. They are made of rubber that has a 65-shore hardness value, just like the oem. They will restore the original ride comfort and are more forgiving than the clubsport (85 shore rubber). This bushing is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65-shore hardness value core. Sold individually. 8 are necessary per car. Please note: this does not include the track rod, the picture circled in red is just for reference.
$65.34
Make a selection FVD33394401SET Replace worn-out original spring plate bushings to return your car to its intended ride quality and performance. This is a high-quality OEM 65 shore density bushing set, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. This set is a direct replacement for the rear axle strut bushings from original part # 477 511 201 and 477 511 202 sold as a set. 1 necessary per axle.
$117.61
Make a selection FVD34391192SET Replace worn-out original front lower control arm bushings with our FVD sport bushings, made of rubber with an 85 shore hardness value that is the same as the rs models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. Features: better handling reduces that sloppy steering feel makes precision adjustments of the suspension easier does not produce any noise like the teflon bushings. Rubber has a shore hardness value of 85 (like rs models) fit's like oem, simple installation made in Germany set is sold per axle. 2 necessary per car.
$171.07
Make a selection FVD34391101SET Replace worn-out original front lower control arm bushings to return your car to its intended suspension geometry and steering feedback. Features: better handling reduces that sloppy steering feel does not produce any noise like the teflon bushings. Rubber has the original shore hardness value of 65 (like oem) fit's like oem, simple installation made in Germany if you are looking for a sportier upgrade we suggest our sport lower control arm set, part # FVD34391192set. Set is sold per axle. 2 necessary per car.
$165.13
Make a selection 90133300309B This rear spring plate is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New OEM spec. (65 shore) rubber bushings are installed to make this a direct bolt on. Features: made from ¼ inch spring steel includes new OEM spec. (65 shore) rubber bushings made in Germany sold individually. Left or right-side fitment. 2 necessary per car.
$331.45
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$236.41
Make a selection 96433102200RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$725.87
Make a selection FVD205996003VAG These bushings are made for h&r front sway bars with 25 mm diameters. They are a direct replacement for our part # . These will also work on any bar with a 25-mm diameter. If you would also like to replace the rear, please use part # FVD205996003hag sold as a front set. 1 set needed per car.
$62.96
Make a selection FVD205993001HA H&r rear sway bar with a 24 mm diameter. 2-way adjustable. This is the rear sway bar from our kit, part # FVD205993001. Includes bushings. Sold individually. 1 needed per car.
$433.62
Make a selection FVD341999R Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with our FVD clubsport series. They are made from rubber with a 85 shore hardness value which is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This is the ideal upgrade for street and light track / clubsport use. This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes 85 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$134.24
Make a selection FVD33150020 This kit is complete and includes the front and rear monoball cartridges with press tools. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 4. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$772.20
Make a selection 99333104503ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install the bushings. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for its return to you. We do not offer a core exchange on this part.
$283.93
Make a selection 477411313M This bushing is made for sway bars with a 21 mm diameter. Sold individually. 2 necessary per car.
From $7.02
Make a selection FVD721TB90P2
$225.72
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |