Vehicles
Sections
60 not categorized PORSCHE 356B REAR SEALCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1978-83 (includes uncategorized and accessory items) FVD911503185186 This seal kit consists of original part # 911 503 185 00 (left) and 911 503 186 00 (right). The set can be used on the trailing edge of the front fender at the cowl just below the windshield. It is also used under the back of the rear quarter panel where it meets the bumper side panel. Genuine part sourced from Porsche ag in Germany to ensure quality, reliability and precise fitment. Sold as a set. 1 set is necessary for front fenders and one set is necessary for the rear. Please note: this is the thinner width. This is not the thicker width from the SC models.
$16.12
Make a selection
$118.80
Make a selection MB1112 The Porsche 911 came equipped from the factory for high performance cornering -- but some things have changed in the almost 40 years the 911 has been on the road. For one, the rubber suspension bushings that monoballs replace are most likely already worn out or cracked from decades of use. General Fitment911 1987-89911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1965-69 912 1965-69
$460.03
Make a selection
$29.70
Make a selection FVD545964000 This rear window is a high-quality lightweight replacement that is designed to perform like the original. It is a replacement for original number, 964 545 107 04. Features: 10 % lighter than original (weighs approx. 6 kg (13.2 lbs)) uses the original seal, part # 96454522500 clean appearance - does not include a cut out rear windshield wiper does not include a rear window defroster grid (less wiring / weight) green tinted, curved design like the original made in Germany please note: be sure to check the model fitment tab to ensure this works on your car.
$804.28
Make a selection FVD33150030 This kit is complete and includes a total of 8, 4 smaller and 4 larger for the rear control arms. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 8. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$806.65
Make a selection FVD3419991 This is a cost effective alternative to buying new control arms. Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with new bushings of the same rubber (65 shore hardness value). This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$134.24
Make a selection 91154303501 Known as: sealing frame / sealing frame f >>91hs1 22159 View/Change Diagram
From $85.32
Make a selection BBI9974010001 Features
$2,046.60
Make a selection 93050417001 This genuine one-piece seal is closest to the rear bumper, we recommend replacing this when removing the motor for maintenance. We recommend replacing both the small and large engine seals, the small is part # 91150411502 sold individually. 1 necessary per car. View/Change Diagram
From $242.35
Make a selection FVD33150020 This kit is complete and includes the front and rear monoball cartridges with press tools. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 4. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$772.20
Make a selection 90150475901 Necessary to seal the torsion bar access cover in front of the rear fender. We also sell a complete cover kit, part # 90150407900 sold individually. 2 necessary per car. Please note: this fits all 911 models up to 1986. View/Change Diagram
From $1.19
Make a selection 90156490505 Genuine part sourced in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. View/Change Diagram
From $16.69
Make a selection 91150332600 This seal sits on the trailing edge of the front fender at the top just below the windshield. It is also used under the back of the rear quarter panel where it meets the side panel. It is also used on the front bumper. We also recommend purchasing the lower seal, part # 91150332500 high-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. View/Change Diagram
From $8.32
Make a selection 90150407900 Necessary to seal the torsion bar access cut out in front of the rear fender. Includes: qty. 1 torsion bar cover qty. 1 cover seal qty. 1 assembly bracket qty. 1 nut sold individually. 2 necessary per car. Please note: this fits all 911 models up to 1986. View/Change Diagram
From $10.12
Make a selection 91150411302 This one-piece seal is furthest from the rear bumper, we recommend replacing this when removing the motor for maintenance. Any of our OEM replacement parts are designed to appear and perform like the originals. We source these parts in Germany to ensure quality, reliability and precise fitment. We recommend replacing both the small and large engine seals, the large is part # 91150411102 sold individually. 1 necessary per car. View/Change Diagram
From $15.12
Make a selection 91150411102 This one-piece seal is closest to the rear bumper, we recommend replacing this when removing the motor for maintenance. Any of our OEM replacement parts are designed to appear and perform like the originals. We source these parts in Germany to ensure quality, reliability and precise fitment. We recommend replacing both the small and large engine seals, the small is part # 91150411302 sold individually. 1 necessary per car. Please note: this only fits 3.0l 930 turbo models from 1975-77. 930 3.3l models require part # 93050417001 View/Change Diagram
From $48.91
Make a selection 91150522100 This seal tends to suffer from dry rot and degrades with time. Be sure to replace it when servicing the bumpers. Any of our OEM replacement parts are designed to appear and perform like the originals. We source these parts in Germany to ensure quality, reliability and precise fitment. When servicing the bumpers, we recommend replacing the shock bushings, part # 91150522100 and base, part # 91150522001 sold individually. 4 necessary per car. 2 front and 2 rear. View/Change Diagram
From $24.79
Make a selection 639570 Finally, brake bleeding can be accomplished by one person! These speed bleeders are available to fit virtually any hydraulic brake or clutch system and uses OEM style sealing area to guarantee a positive leak-proof seal. Speed bleeders permanently replace original bleeder screw and come 2 per package with dust protection caps. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1987-89
$42.12
Make a selection FVD33150046R Replace worn-out original soft rubber (65 shore hardness value) track rod bushings with our FVD clubsport series. They are made of rubber that has an 85-shore hardness value, the same as the rs models. 85-shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes an 85-shore hardness value core. Sold individually. 8 are necessary per car. Please note: this does not include the track rod, the picture circled in red is just for reference.
$71.28
Make a selection 93035255302 Rear 8 required per car 4 per caliper View/Change Diagram
From $3.41
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |