PORSCHE CAYENNE A CONTROL ARMCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1978-83 - Rear Axle (includes uncategorized and accessory items) 99734105304BU2 Diese buchse ersetzt an ihrem vorderen querlenker die hintere buchse. Wie oe in 65 shore harte. Preis pro satz, pro querlenker wird ein satz benotigt.
$93.50
Make a selection FVD33150030 This kit is complete and includes a total of 8, 4 smaller and 4 larger for the rear control arms. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 8. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$746.90
Make a selection FVD34101802RAK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrange...(choose a part on the right to read more)
$438.90
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$218.90
Make a selection FVD34101702RAT We will send you a reconditioned control arm, kindly send back your old part, or core . The reconditioned control arm has been full inspected, disassembled, degreased and we have properly installed FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. This part is sold on an exchange basis, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and r...(choose a part on the right to read more)
$440.00
Make a selection FVD34101702ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection FVD33150045 Original rubber replacement bushing (65 shore hardness value) for the rear control arms (camber link and caster link). This bushing cartridge is weather sealed and is crafted in high carbon steel and 7075 t6 aircraft aluminum. Sold individually.
$64.90
Make a selection FVD34101802RAT We will send you a reconditioned control arm, kindly send back your old part, or core . The reconditioned control arm has been full inspected, disassembled, degreased and we have properly installed FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner please note: each control arm is remanufactured in Germany, so the lead times can vary. This part is sold on an exchange basis, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and re...(choose a part on the right to read more)
$440.00
Make a selection FVD34101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection FVD34102702ATK By ordering this part number you get after previous sending in your wishbone overhauled with new race-silent blocs back. The race-silent blocs (85 shore) give you more stable driving. Should it not be repairable, we will inform you immediately.
$279.40
Make a selection FVD34102800ATK By ordering this part number you get after previous sending in your wishbone overhauled with new race-silent blocs back. The race-silent blocs (85 shore) give you more stable driving. Should it not be repairable, we will inform you immediately.
$279.40
Make a selection FVD341999R Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with our FVD clubsport series. They are made from rubber with a 85 shore hardness value which is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This is the ideal upgrade for street and light track / clubsport use. This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes 85 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection
$48.51
Make a selection
$331.66
Make a selection
$323.09
Make a selection FVD631997LEDUS Us version. Looking for the latest 997.2 led lighting for you 997.1? We have the solution. Now you can purchase Porsche factory tail lights and install seamlessly with our led conversion units. Description: - can be used with Porsche OEM factory tail lights (us version) - will not trigger warning lights - works seamlessly with Bosch electronic control unit (no need for additional load resistors) - simple plug and play installation warning this will not work on 2009 997.1 turbos!
$544.50
Make a selection MV8500 Kit includes everything for performing hundreds of automotive diagnostic and mechanical tests. Used for one-person brake bleeding, produces vacuum or pressure at the turn of a switch. Comfortable ergonomic design with one-finger trigger vacuum/pressure release. Durable die-cast metal construction for long life. Pressure and vacuum are created on the squeeze stroke for superior accuracy and control. General FitmentACCESSORY
$90.25
Make a selection WAP06004610 Porsche bike s is a superbly built, lightweight "hardtail" that tackles mountains with an amazing battery of technologies. Start with its rigid triangulated frame of ultralight 7020 alloy aluminum, built around a 60mm main tube for stiffness and control. Add a motorcycle-style suspension fork for a smooth ride. Then bolt on the shimano rapid fire shifters for quick shifts on the go, plus magura hydraulic brakes for an astounding level of stop. And don't forget the shimano lx gearing that allows for smooth, rapid shifts (up to three shifts per stroke) even under a full load. The final result: a two-wheeled machine that's worthy of the name Porsche. Made in Germany.
$2,501.08
Make a selection FVD72150001 Our software is capable of displaying and clearing trouble codes on most control modules. Most Porsche cars made since 1990 have multiple computers built into different parts of the car. These computers are capable of self-diagnosis. In other words, the car knows what is wrong and our tool allows you to see this information. Until now people needed to rely on car dealers to read this information from each of the car's computers. Now our software allow shops and individuals to read the fault code information out of most control modules. What does it do? · reset service reminders · reads diagnostic trouble codes · displays actual values · shows ecu information · clears diagnostic trouble codes ÂÂ...(choose a part on the right to read more)
$325.60
Make a selection FVD211622 This silicone hose supplies hot air to the heater control box, it replaces original part # 930 211 622 01. It runs from the exhaust heat exchanger to the heater control box. We recommend replacing the heater box clamp, part # 90121105122 on one end and a hose clamp part # 99951234902 on the other end. Sold individually. 2 necessary per car.
$52.80
Make a selection 240991351GS Pagid yellow rsl 29 are from the rsl line of endurance racing brake pads. They are a medium friction coefficient racing compound with long pad and disc life, and are easily bedded in. Rsl 29 pads are manufactured of a low metallic resin bonded material containing steel and acrylic fibers. They operate in a wide operating temperature range and offer excellent release characteristics. Rsl29 pads offer low heat conductivity and work well with abs systems. They offer excellent modulation and controllability. They offer lower disc wear rates and are fade resistant up to a temperature of 650*c (1,202*f). Applications include: club racing, track days, touring cars, prototype endurance racing and GT cars. Features at a...(choose a part on the right to read more)
$708.40
Make a selection FVD3511M39040AS The brembo gran turismo s (gt-s) braking system is ideal for clubsport and sprint type track events. The GT-s type iii system utilizes brembo type iii aggressive face type discs that offer high initial response with a smooth pedal feel. The type iii offers the highest overall braking confidence and control, allowing a quick qualifying time or top results in sprint races. Gt-s systems contain advanced calipers that include racing style radiators, dual inner piston seals, an inner pressure seal and an outer wiper seal. This innovative design provides the best combination of performance and long-lasting track use. The calipers are hard anodized in black (machined brembo logo in red) for resistance to corrosion and...(choose a part on the right to read more)
$5,164.50
Make a selection FVD3522P38056A2 The brembo gran turismo (gt) braking system with type iii rotors is ideal for ideal for clubsport and sprint type track events. It utilizes brembo type iii aggressive face-type discs that offer high initial response with a smooth pedal feel. The type iii offers the highest overall braking confidence and control, allowing a quick qualifying time or top results in sprint races. The GT line is dedicated to the most demanding customers. It originates from racing components, consisting of floating ventilated cross drilled discs, aluminum calipers with opposed pistons, a complete set of high-performance brake pads, abrasion and corrosion resistant goodridge braided steel brake lines and high-quality fastener hardware...(choose a part on the right to read more)
$4,064.50
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |