PORSCHE 930 DEL SOLCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1978-83 - Electrical (includes uncategorized and accessory items) 99919233850EQ Belts undergo a lot of friction and wear. They are cost effective to change and will keep your alternator and engine in good condition. Be sure to follow recommended service and replacement intervals set by Porsche on belts. Please note: specific model fitment information below. Sold individually. 1 necessary per car.
$15.44
Make a selection 9A160410300EQ If your starter is on its way out, you will notice an intermittent clicking noise and a delay in the vehicle starting. Eventually, you will hear a metallic screeching noise that is a sure sign that your starters bendix mechanism, bearings or solenoid are kaput. When ordering a new starter, be sure to check the protection cap on the terminal for cracks which allows moisture in and causes pre-mature failure. High-quality denso OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
$523.91
Make a selection 9A160618101 Oxygen or lambda sensors are critical to your engine's health. If the sensor is faulty you may experience poor gas mileage, rough idling or engine pinging. Replace it with this high-quality Bosch OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per car. Please note: be sure to check the "fits these models" tab to make sure that this will work for your model / application.
From $143.75
Make a selection BBI9963010001 The bbi autosport Porsche 996/997 turbo clutch slave cylinder conversion kit is a direct replacement part that eliminates the problematic factory power-assist system for improved reliability and pedal feedback. The factory power-assisted clutch system has always been the achilles heel for the Porsche 997 turbo. Utilizing the power steering system to help reduce the force needed to depress the clutch pedal, it is a flawed design that delivers a mushy pedal feel with poor feedback, and is highly prone to failure.
$1,436.40
Make a selection BES99110200SK "brombacher" stainless steel exhaust system with valves for the 991 + 25 hp & + 20 tq gain. - 200 cell hjs "hd" sport catalysts. - 25 lb. Weight savings over OEM system (weighs 59 lbs. (27,0 kg), OEM weighs 84 lbs. (38kg). - 2 3/4 tubing (70mm). - 4 x 3.5 (90mm) round tips. - motorsport merge collector. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - absolutely no drone in the cabin. - "aero quip" style motorsport connections without gaskets or flanges to ensure a leak free exhaust. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - under load (moving) with valves closed: 85db* - under load (movin...(choose a part on the right to read more)
$10,833.37
Make a selection FVD34101707ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$451.44
Make a selection FVD890930183 We recommend changing your ignition cables when changing your plugs and distributor. Overlooking the ignition cables can lead to increased resistance and weak spark which causes incomplete combustion in the cylinder and robs your engine of power and efficiency. These cables are high-quality OEM (original equipment manufacturer) beru replacement, designed to perform like the original. We like that they incorporate secure wire ends with a brass receptacle and steel click spring. They also include correct OEM style protection sleeves and wire clips. We source these in Germany to ensure quality, reliability and precise fitment. Sold as a complete set. Please note: please check the model fitment tab to ensure accura...(choose a part on the right to read more)
$378.97
Make a selection FVD631404 Don't let cracked or faded lenses detract from your cars appearance. Replace them with these high-quality OEM replacements, designed to perform like the originals. The red lenses were genuine equipment on usa models, but they really clean up the rear when added in place of the amber look. Quality replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Sold as a set. 1 necessary per car.
$129.49
Make a selection HEI964001009S Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long-standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: bolt-in bar - screwed in to the original seat belt points. Aluminum 1.5-inch diameter tubing, .098 wall thickness tubing. Bars which connect to the main hoop, use a connecting joint system. Black paint finish. We recommend adding the harness bar, part # hei600036s to your order as it is sold al...(choose a part on the right to read more)
$1,733.29
Make a selection FVD911503185186 This seal kit consists of original part # 911 503 185 00 (left) and 911 503 186 00 (right). The set can be used on the trailing edge of the front fender at the cowl just below the windshield. It is also used under the back of the rear quarter panel where it meets the bumper side panel. Genuine part sourced from Porsche ag in Germany to ensure quality, reliability and precise fitment. Sold as a set. 1 set is necessary for front fenders and one set is necessary for the rear. Please note: this is the thinner width. This is not the thicker width from the SC models.
$16.12
Make a selection BES95B05040SK + 15 hp & + 18 tq gain. - 2.5 tubing (63.5mm). - 4 x 4 (101mm) round tips. - 8.5 lb. Weight savings over OEM mufflers. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - electronic valve controller must be removed from the OEM unit and added to our muffler. - made in Germany. Please note: this muffler is a direct replacement the macan turbo (95b) model which comes with a single electronic exhaust valve on the passenger side. This is the very 1st aftermarket muffler for the macan 95b turbo that includes a valve like the factory system. This allows our system ...(choose a part on the right to read more)
$4,907.63
Make a selection FVD211343 Already replaced your heater blower tube with a carbon bypass? This carbon / kevlar air duct will match the engine decor perfectly. It is a replica of the factory rs lightweight factory air duct. This is a quality tuning product manufactured by dansk. They offer a complete line of tuning and performance parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment manufacturers (oem) to Porsche in Germany. This installs easily and really dresses up the engine. Sold individually. 1 necessary per car.
$288.68
Make a selection FVD33399300 A cost effective FVD exclusive combination of bilstein clubsport shocks with a set of TUV certified eibach springs. This suspension kit will lower the front axle to a maximum of 35 mm (1.37 inches) and the rear axle to 30 mm (1.18 inches), like the European rennsport model. The height is adjustable as the dampers are threaded. They are a cost effective solution for clubsport use and will be well mannered on the street. Sold as a complete kit. 1 kit is necessary per car.
$3,323.19
Make a selection FVD11GK181GF Motorsport quality grp (glass-reinforced plastic) front bumper bar. Features: - produced by an German motorsport manufacturer. - lightweight 5.7 lbs. (2.6 kg) - made of high strength, grp (glass-reinforced plastic) sold individually. 1 necessary per car. Please note: please provide us with the year / model. These are motorsport quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world. All grp products must properly be fitted and completely prepared prior to paint.
$604.69
Make a selection FVD33150046R Replace worn-out original soft rubber (65 shore hardness value) track rod bushings with our FVD clubsport series. They are made of rubber that has an 85-shore hardness value, the same as the rs models. 85-shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes an 85-shore hardness value core. Sold individually. 8 are necessary per car. Please note: this does not include the track rod, the picture circled in red is just for reference.
$71.28
Make a selection FVD201911964993 Looking to update your fuel cap? This is a cost effective, sporty, aluminum alternative to the factory cap. It resembles the tequipment cap available on the water-cooled models. It is a quality tuning product manufactured by dansk. They offer a complete line of tuning and performance parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment manufacturers (oem) to Porsche in Germany. Oem non-locking, screw type fuel cap sourced in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary ...(choose a part on the right to read more) General FitmentACCESSORY
$147.31
Make a selection 9A110221200 High-quality ina OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. This part includes the protection cap, bearing and roller housing. Sold individually. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.
From $20.79
Make a selection 91163195100EQ Don't let a cracked or faded lens detract from your cars appearance. Replace it with this high-quality OEM replacement, designed to perform like the original. This was genuine equipment on usa models but really cleans up the rear when added in place of the amber look. Quality replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Sold individually. Driver's side fitment. 1 necessary per car. Lookin...(choose a part on the right to read more)
$97.42
Make a selection FVD20799601 Scavenging and aeration in the oil pan have been identified as a problem in 996 and Boxster models experiencing high g-forces on the racetrack. This oil pan spacer provides a simple solution. This spacer increases sump capacity by half a liter, providing more reserve to ward off starvation. Thisoil pan spacer clears all factory options including the rear skid plate. Added oil capacities as well as increased oil pan surface area increase oil cooling and engine performance. *oil pan and sump baffle are OEM parts and do not need to be purchased material: 6061 t6 aluminum alloy finish: clear anodized weight: n/a models: Boxster, Boxster s, and 996 models (excludes GT3 and turbocharged models) installation: for best...(choose a part on the right to read more)
$306.50
Make a selection FVD72269500LGW This simple FVD Brombachertow hook installs in seconds and folds down to eliminate protrusion from the car's bodywork. It fits all Porsche's with factory left hand thread, screw-type tow hooks. It has a two-inch towing eye, which is required for track events. It is precision cnc machined stainless steel, tig-welded, has a polished shaft and a rubber locking rod to prevent loosening. Features: stainless steel light weight: 1.6 lbs. Fits any Porsche listed in our fits these models tab. Installs in seconds, simply remove the bumper plug and screw into the tow hook hole. Made in Germany. Includes FVD Brombacherlogo. Sold individually.
$148.50
Make a selection FVD50193500 Steel, prime coated floor pan repair panel made by dansk. They offer a complete line of replacement bodywork to complement the entire Porsche model range. All dansk products are manufactured to European standards to ensure the quality that you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Sold individually. 1 necessary per car. Please note: due to variances in production at the factory, age, accident damage or rust, each part may require trimming and or adjustment for perfect fitment.
$342.14
Make a selection FVD50599109MM The moshammer stormforce evo rs front chin spoiler for the c2 / c2s / c4 / c4s and the t models blends a bit of Porsche heritage into its design with canard style winglets. This effective design transforms turbulent air into a more laminar flow, creating added downforce and uplift reduction. It also incorporates twin air guides to assist with brake ventilation and underbody air flow efficiency. The moshammer stormforce evo rs front chin spoiler design offers exclusive aesthetics, aero functionality and it is secured seamlessly into the factory locations without modification. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added...(choose a part on the right to read more)
$1,336.50
Make a selection FVD34391192SET Replace worn-out original front lower control arm bushings with our FVD sport bushings, made of rubber with an 85 shore hardness value that is the same as the rs models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. Features: better handling reduces that sloppy steering feel makes precision adjustments of the suspension easier does not produce any noise like the teflon bushings. Rubber has a shore hardness value of 85 (like rs models) fit's like oem, simple installation made in Germany set is sold per axle. 2 necessary per car.
$171.07
Make a selection FVD361900715EU This fuchs replica is a classic design perfectly suited for any Porsche model. The center section is cast aluminum and finished black with a layer of clear coat. TUV approval documentation is standard with each wheel. The wheel accepts factory Porsche wheel bolts and center caps. Center caps sold separately, part # 190361035 or 190361033 sold individually.
$443.12
Make a selection FVD511RSKIT This manual support replaces the OEM hood shocks to save weight. It can be used on kevlar / gfk / aluminum hoods. The kit is comprised of genuine parts and was originally manufactured for the rennsport models. Weighs: .12 kg (.26 lbs.) sold individually. 1 necessary per car.
$108.11
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |