![](https://30ed524141d0cac60ab4-d2e2d18a14257de3b9ce428cf077ee97.ssl.cf2.rackcdn.com/acban.jpg)
PORSCHE 356 A FORCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1978-83 - Body (includes uncategorized and accessory items) ![]() 115910996004 Bilstein b4 OEM (original equipment manufacturer) replacement shock absorber set (4 pieces) for your Porsche with standard suspension. The b4 dampers from bilstein are the perfect replacement for your Porsche. Facts: - constant damping power under any load - high power reserves for maximum safety - ride like it's the first time, every time - OEM quality - bilstein gas pressure technology
$1,753.99
Make a selection 115900997BIT021 The pss 10 suspension kit provides the ultimate in performance tuning. The fully adjustable monotube gas shock absorbers offer a selection of nine precise compression and rebound settings. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Handling and control are just a few twists away. Regardless of whether in daily motoring, on the nordschleife of the nurburgring at the weekend, in training courses or in club sports - it's all pure driving enjoyment! Product advantages at a glance: • bilstein mono-tube/inverted technology • bilstein road tested and tuned • high driving dynamics with g...(choose a part on the right to read more)
$4,345.00
Make a selection 190721965901
$145.20
Make a selection 21011124OK Catalytic bypass pipe "u-torque" design, manufactured by m&m in Germany. The u-torque design compensates for the backpressure loss while running without cats. The design minimizes the loss of low end torque and adds 10-15 ft-lbs of torque in the mid and top range of the rpms. Why settle for the traditional cross over cat design when you can add torque in the mid-range and minimize the loss of torque down low where the 997's need it most! Ecu software is necessary !
$1,094.50
Make a selection 115910996002 Bilstein b4 OEM (original equipment manufacturer) replacement shock absorber set (4 pieces) for your Porsche with standard suspension. The b4 dampers from bilstein are the perfect replacement for your Porsche. Facts: - constant damping power under any load - high power reserves for maximum safety - ride like it's the first time, every time - OEM quality - bilstein gas pressure technology
$1,733.15
Make a selection 115901HLS980 -wird am gewindefahrwerk zwischen federteller und feder montiert. - je nach gegebenheit bis zu 45 mm anhebbar - im fahrbetrieb(bis 80 km/h) aktivierbar - schnelles anheben in 4-5 sekunden
$12,117.60
Make a selection 115005001
$282.70
Make a selection 61610013895 Third 75mm case/standard inside crank
From $556.60
Make a selection
$11.25
Make a selection 61610390406SET Special orderset of 4. Fits 356 sc/912. (1600cc. Compression ratio 9.3:1. Cylinder material, nikasil. Bore surface, alloy. Piston design, 3 ring, short skirt. Manufacturermahle.
From $2,772.00
Make a selection 115333201
$454.30
Make a selection 61340H This roll bar will give your street car a performance look and style. In most cars rear seats and/or convertible top remain in place and useable. 4 point roll bar is made of 1.750 x .120 dom mild steel tube. All necessary installation and mounting hardware with back-up plates is included. *this is not a DOT safety device. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1987-89
$635.19
Make a selection 35652807SET New profile to match original for proper sealing on early cars 35652807
$220.00
Make a selection 115005004
$275.00
Make a selection 115900944018CS Sports suspension for 924 - 944 - 968 only for 18mm spring strut mounting this sports suspension is for everyday use and increase the dynamic and response. The lowering is adjustable (30-70mm front and 30-60mm rear). By using springs at the rear axle instead of torsion bars you improve extreme the handling of your car. By removing the rear torsion bars is the weight saving approximately 25kg.
$3,132.80
Make a selection 113851842AG Fits on 330mm breaks (5-hole), exterior 1.5 inches , interior 7.5 inches
$1,805.10
Make a selection 115900991BIH Specifically for use bilstein coil over kits for cars with pdcc and for vehicles with active front stabilizer bar. Also for use with clubsport kits. This limits lowering range to minimum specification. This is bilstein part # 11-239680
$350.90
Make a selection 115000001 Support nut for our part # 115112 115113 115115 and 115116 etc. Internal thread: 4.7cm total height of the ring: 2.0cm height of the upper part of the screw ring including the thread: 1.2cm sold individually
$50.60
Make a selection 115000003 Support nut for our part # 115114 115115 and 115116 etc. Internal thread: 4.7cm total height of the ring: 2.2cm height of the upper part of the screw ring including the thread: 1.4cm sold individually
$38.50
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |