Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Panamera models with optional air suspension utilize four sensors to control the ride height. This is accomplished via the use of a small linkage or link which connects the sensor to the suspension. As the car is raised or lowered, the link moves the sensor up or down sending a signal to the computer telling it how high the car is. When you replace the non-adjustable factory link with this adjustable design, the output of the sensor makes the computer believe that the car is higher than it is. So, the computer will lower the ride height. The simplicity of this setup is that it retains full functionality of the factory system. Be warned, all adjustable lowering links are not the same! These links are machined al...(choose a part on the right to read more)

Enhance steering precision and steering feedback by simply replacing your original tie rods. Turbo tie rods use a spherical inner joint instead of soft rubber bushings. They offer quicker steering response, more sensitivity and more precision. These are standard length we highly recommend them for lowered vehicles with bump steer kits like part # FVD34791100 or FVD347911930 . We also offer turbo tie rods in longer lengths for other applications, check part # FVD34791180r and FVD34791181ry this kit is manufactured in Germany by an OEM supplier, made from high carbon steel and 7075 t6 aluminum. Kit includes: 2 qty. Outer tie rods 2 qty. Inner tie rods 2 qty. Spacing washers 2 qty. Boots 2 qty. Castle nuts 2 qty. ...(choose a part on the right to read more)

Restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm cannot compensate enough when lowering your Porsche, leaving you with as much as ½ inch of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration. Sold in pairs. 1 necessary per car.

This item may need to be so...(choose a part on the right to read more)

This non-adjustable rear spring plate is remanufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New rs spec. (85 shore) rubber bushings are installed to make this a direct bolt on. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Features: includes new rs spec. (85 shore) rubber bushings made in Germany sold individually. 2 necessary per car. This part is a remanufactured part. Send us your original and we will have it remanufactured for you. We do not offer a core exchange on this part. Each is remanufactured in Germany, so the lead times can vary.

...(choose a part on the right to read more)

Quality made in Germany. We recommend installing a new rubber sealing ring, part # 91164190201. Made of acrylic. Includes the cut out for the trip counter. Sold individually. 1 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)

Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)

Solid bushings and mounts allow you to achieve exact suspension articulation which improves handling and stability on lowered / race prepared cars. The original soft rubber bushings can deform under track loads which allows the sub frame to shift and throw the camber and toe off. Solid bushings will not deform and will keep the camber and toe settings in line which equates to confidence in cornering and faster lap times. These are intended to replace the soft rubber bushings on the original rear sub frame (part #'s 993 331 051 00 & 993 331 052 00). They are made in Germany and are TUV approved. Sold as a set. 1 set is necessary per car. Please note: if you are also driving your car on the street, they will res...(choose a part on the right to read more)

Replace worn-out original front lower control arm bushings with our FVD sport bushings, made of rubber with an 85 shore hardness value that is the same as the rs models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. Features: better handling reduces that sloppy steering feel makes precision adjustments of the suspension easier does not produce any noise like the teflon bushings. Rubber has a shore hardness value of 85 (like rs models) fit's like oem, simple installation made in Germany set is sold per axle. 2 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be ...(choose a part on the right to read more)

Our rear spring plate set is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. The adjustability allows for precise re-indexing of the torsion bar 1 ½ inches up or down. New OEM spec. (65 shore) rubber bushings are installed to make this a direct bolt on without the hassle of adding new bushings. Each plate is clearly marked for indexing purposes and includes complete installation instructions. Features: made from ¼ inch spring steel adjustment range of 1 ½ inches up or down includes new OEM spec. (65 shore) rubber bushings clearly marked for accurate installation and indexing made in Germany sold individually. 2 necessary per car. Plea...(choose a part on the right to read more)

View/Change Diagram

911 1974-77 - Rear Axle	911 1978-83 - Rear Axle
911 1984-86 - Rear Axle	911 1987-89 - Rear Axle
930 1975-77 - Rear Axle

Known as: articulated ring for shock absorber / articulated ring / rubber mounting

View/Change Diagram

356 1950-59 - Rear Axle	356 1950-59 - Rear Axle
356 1960-65 - Front Axle/Steering	356 1960-65 - Rear Axle
911 1970-73 - Rear Axle	911 1974-77 - Rear Axle
911 1978-83 - Rear Axle	911 1984-86 - Rear Axle
911 1987-89 - Rear Axle	930 1975-77 - Rear Axle
912 1965-69 - Rear Axle	912 1965-69 - Rear Axle
911 1965-69 - Rear Axle	911 1965-69 - Rear Axle

Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's 911 models from 1978-89 if fitted with an 18mm original rear sway bar.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited s...(choose a part on the right to read more)

Replace worn-out spring plate bushings with these longer lasting poly-graphite plastic bushings. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This includes the inner and outer bushing for the 2-piece adjustable spring plate. Sold individually. 2 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Replace worn-out original front control arm / wishbone bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This is located at the front of the control arm / wishbone. The correct matching poly-graphite bushing for the front of the control arm is part # 150tbf900 sold individually. 2 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Replace the worn-out spring plate bushing with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This is the inner bushing for the 1-piece non-adjustable spring plate. Sold individually. 2 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Steering rack and pinion bellow boot cover. keep the dust out of your steering system to avoid expensive repairs. replace both at the same time for peace of mind. the 40 year old rubber is probably cracked or split, so change them now, while you still can.

View/Change Diagram

911 1970-73 - Front Axle/Steering	911 1974-77 - Front Axle/Steering
911 1978-83 - Front Axle/Steering	911 1984-86 - Front Axle/Steering
911 1987-89 - Front Axle/Steering	912 1965-69 - Front Axle/Steering
912 1965-69 - Front Axle/Steering	914 1970-76 - Front Axle/Steering
911 1965-69 - Front Axle/Steering	911 1965-69 - Front Axle/Steering

If your starter is on its way out, you will notice an intermittent clicking noise and a delay in the vehicle starting. Eventually you hear a metallic screeching noise that is a sure sign that your starters bendix mechanism, bearings or solenoid are kaput. When ordering a new starter be sure to check the rubber cap on the terminal for cracks which allows moisture in and it is a good idea to check your starters hardware as well.
Features: Bosch remanufactured starter from Germany. Armature continuity tested, gauged, straightened and shimmed. All shaft splines and load bearing surfaces lubricated with oe high temp. Materials. Includes highest quality replacement parts, including starter drive components, solenoid...(choose a part on the right to read more)

General Fitment

Since 1984, we have established an extensive network of interior specialty vendors that have stockpiled historically correct materials and have the skills necessary to reproduce to o.e. Specifications. Each carpet set is produced in Germany and includes every concours quality detail. Features: genuine German sliverknit velour - wool carpet thick / plush historically correct drivers side includes original script in gold original fitment jute/rubber backing for floor carpets heel padding vinyl bound edges for floor carpets all necessary cut outs and buttons manufactured in Germany sold as a complete set. 1 necessary per car. Please note: when ordering, please indicate the year, model, transmission, with/without f...(choose a part on the right to read more)

Since 1984, we have established an extensive network of interior specialty vendors that have stockpiled historically correct materials and have the skills necessary to reproduce to o.e. Specifications. Each carpet set is produced in Germany and includes every concours quality detail. Features: genuine German sliverknit velour - wool carpet thick / plush historically correct drivers side includes original script in gold original fitment jute/rubber backing for floor carpets heel padding vinyl bound edges for floor carpets all necessary cut outs and buttons manufactured in Germany sold as a complete set. 1 necessary per car. Please note: when ordering, please indicate the year, model, transmission, with/without f...(choose a part on the right to read more)

Since 1984, we have established an extensive network of interior specialty vendors that have stockpiled historically correct materials and have the skills necessary to reproduce to o.e. Specifications. Each carpet set is produced in Germany and includes every concours quality detail. Features: genuine German sliverknit velour - wool carpet thick / plush historically correct drivers side includes original script in gold original fitment jute/rubber backing for floor carpets heel padding vinyl bound edges for floor carpets all necessary cut outs and buttons manufactured in Germany sold as a complete set. 1 necessary per car. Please note: when ordering, please indicate the year, model, transmission, with/without f...(choose a part on the right to read more)

Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Since 1984, we have established an extensive network of interior specialty vendors that have stockpiled historically correct materials and have the skills necessary to reproduce to o.e. Specifications. Each carpet set is produced in Germany and includes every concours quality detail. Features: genuine German sliverknit velour - wool carpet thick / plush historically correct drivers side includes original script in gold original fitment jute/rubber backing for floor carpets heel padding vinyl bound edges for floor carpets all necessary cut outs and buttons manufactured in Germany sold as a complete set. 1 necessary per car. Please note: when ordering, please indicate the year, model, transmission, with/without f...(choose a part on the right to read more)

Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)

Remanufactured part sourced in Germany. Includes a new rubber sealing ring. Purchase a newly remanufactured unit from us and an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and resell-able, the core deposit will be refunded. Sold individually. 1 necessary per car. Please note: this is a special-order item. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis. Please call us in advance of placing your order, these are very hard to come by and in some instances, we c...(choose a part on the right to read more)