PORSCHE CAYMAN S FORCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1974-77 - Fuel/Exhaust (includes uncategorized and accessory items) 113101849AS 3-piece bbs motorsport wheel with forged aluminum center star can be mounted using either an OEM bolt pattern or a center lock setup. Weight optimized performance wheel featuring relief-milled spokes that offer unparalleled strength and stability. Available in many different sizes and offsets and center star available in silver, gold, black and white at no additional charge
$2,278.58
Make a selection 115910986001 Bilstein b4 OEM (original equipment manufacturer) replacement shock absorber set (4 pieces) for your Porsche with standard suspension. The b4 dampers from bilstein are the perfect replacement for your Porsche. Facts: - constant damping power under any load - high power reserves for maximum safety - ride like it's the first time, every time - OEM quality - bilstein gas pressure technology
$1,170.18
Make a selection 115005004
$297.00
Make a selection 115333201
$490.64
Make a selection 115900911030
$4,905.25
Make a selection 113851843AG 3-piece bbs motorsport wheel with forged aluminum center star can be mounted using either an OEM bolt pattern or a center lock setup. Weight optimized performance wheel featuring relief-milled spokes that offer unparalleled strength and stability. Available in many different sizes and offsets and center star available in silver, gold, black and white at no additional charge
$1,949.51
Make a selection 115003A01
$16.63
Make a selection 113851842AG Fits on 330mm breaks (5-hole), exterior 1.5 inches , interior 7.5 inches
$1,949.51
Make a selection 115900944018CUP
$4,348.08
Make a selection 115343201
$490.64
Make a selection 115343203
$621.32
Make a selection 240999352CRRSC1 Racing pads for pccb ( ceramic brake system)
$710.42
Make a selection 115333203
$573.80
Make a selection 115900944020CS Double spring suspension (racing) for 924 only for 20mm spring strut mounting this sport suspension was tuned and tested for racing use only (hockenheimring.net). Perfect handling, recommended for race and clubsport. Not for street use (racing suspension). The lowering is adjustable (30-70mm front and 30-60mm rear). By using springs at the rear axle instead of torsion bars you improve extreme the handling of your car. By removing the rear torsion bars is the weight saving approximately 25kg.
$2,844.07
Make a selection 115343615B8 Twintube strut assembly setting: b8 sport (sp) drive type: awd position: front quantity per vehicle: 2 bilstein b8 sport shocks and struts deliver absolute mastery of the road surface for the performance-minded driver. Designed to push a car's suspension to its performance peak, these shocks are specifically suited for use with special lowering springs in combination with anti-sway bars or other suspension upgrades. (yellow paint, steel body)
$523.91
Make a selection 115000003R01 Support nut for our part # 115114 115115 and 115116 etc. Internal thread: 4.7cm total height of the ring: 2.2cm height of the upper part of the screw ring including the thread: 1.4cm sold individually like new
$1.94
Make a selection 210111096GT3RR01 Like new
$611.82
Make a selection 21011125PSE Only for vehicles with Porsche standard sports exhaust system 200 cell, hjs tri-metal, hf (high flow) hjs catalytic cores with "u-torque" design, manufactured by m in Germany. The u-torque design compensates for the backpressure loss while running the high flow cats. The design minimizes the loss of low end torque and adds 10-15 ft-lbs of torque in the mid and top range of the rpms. Why settle for the traditional cross over cat design when you can add more torque in the mid-range and minimize the loss of torque down low where the 997's need it most! Please note: these fit the OEM mufflers and Porsche sport exhaust (pse) mufflers. Tech tip:add one of our installation kits FVD mk 997300
$3,575.88
Make a selection 150SPB965 Replace the worn-out spring plate bushing with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This is the inner bushing for the 1-piece non-adjustable spring plate. Sold individually. 2 necessary per car.
$51.08
Make a selection 115900991BIH Specifically for use bilstein coil over kits for cars with pdcc and for vehicles with active front stabilizer bar. Also for use with clubsport kits. This limits lowering range to minimum specification. This is bilstein part # 11-239680
$378.97
Make a selection 115900997BIT021 The pss 10 suspension kit provides the ultimate in performance tuning. The fully adjustable monotube gas shock absorbers offer a selection of nine precise compression and rebound settings. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Handling and control are just a few twists away. Regardless of whether in daily motoring, on the nordschleife of the nurburgring at the weekend, in training courses or in club sports - it's all pure driving enjoyment! Product advantages at a glance: • bilstein mono-tube/inverted technology • bilstein road tested and tuned • high driving dynamics with g...(choose a part on the right to read more)
$4,692.60
Make a selection 22011099103
$1,158.30
Make a selection 115900991BI01 This bilstein b16 damptronic active coil over suspension kit features ride height and damping adjustability that is compatible with the Porsche pasm electronic damping system. The damptronic system constantly monitors the road surface via sensors, so the vehicle adjusts for perfect traction, unparalleled control and stable handling. Each active Porsche electronic suspension feature, control and setting is retained and all function in the same manner. The front and rear progressive rate springs are matched with bilstein's famous monotube performance dampers. This suspension is custom tuned for the 991.1 and 991.2 variants. The front and rear threaded damper bodies allow .8 - 1.5 inches (20-40 mm) of travel whic...(choose a part on the right to read more)
$5,198.69
Make a selection 115000001 Support nut for our part # 115112 115113 115115 and 115116 etc. Internal thread: 4.7cm total height of the ring: 2.0cm height of the upper part of the screw ring including the thread: 1.2cm sold individually
$54.65
Make a selection 115000003 Support nut for our part # 115114 115115 and 115116 etc. Internal thread: 4.7cm total height of the ring: 2.2cm height of the upper part of the screw ring including the thread: 1.4cm sold individually
$41.58
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |