PORSCHE 944 MENS RINGCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1974-77 - Engine (includes uncategorized and accessory items) 96433106080 Our spring plates are manufactured in europe by an OEM supplier to Porsche using the finest materials (high carbon steel, 7075 t6 aluminum and 65 shore rubber - oe spec). Sold individually. Right side fitment. 1 qty. Required.
$680.00
Make a selection 96433102200RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$705.71
Make a selection 91110394902SET6 High-quality OEM replacement piston and cylinder set designed to perform like the original. We source these parts in Germany to ensure quality, reliability and precise fitment. Set includes: 6 qty. Pistons 6 qty. Cylinder 6 qty. Wrist pin 12 qty. Circlips 1 qty. Set of piston rings sold as a set. 1 necessary per car.
$5,337.37
Make a selection 91160623000 This oil pressure switch is a critical oil system component. When the oil pressure drops below 0.3 bar, this switch lights the warning light located on the oil pressure guage in the instrument cluster. This switch is located on the crankcase. We also recommend replacing the crush washer / sealing ring that sits under the banjo bolt, part # 90012300730 . This sits very near the oil thermostat, part # 93010776500 , so this would be a good time to replace it as well. High-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. Please note: this is not for sportomatic models. View/Change Diagram
From $5.25
Make a selection 91110190160 Genuine complete set of bearings (including # 8) sourced from Porsche ag in Germany to ensure quality, reliability and precise fitment. Set includes: 1 qty. Crankshaft main bushing sleeve - bushing viii - oversize +0.25mm 12 qty. Crankshaft main bearing shells ii-vii (half) - oversize +0.25mm 2 qty. Crankshaft main bearing shells i (half) - oversize +0.25mm sold as a set. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment. View/Change Diagram
$1,091.54
Make a selection 91134101310ATK The reconditioning process includes full inspection of the cross member to ensure proper operation after the remanufacturing process. We then disassemble, degrease and media blast the part. Once fully prepared, we seal it with a corrosion resistant plating. Send us your cross member and we will have it reconditioned for you. We do not offer a core exchange on this part. If your original part is defective and cannot be salvaged, we will notify you and make arrangements for its return. Sold individually. 1 necessary per car.
$235.62
Make a selection 91153170102 As a striker plate ages, it will start to rattle and can potentially be a safety risk. We recommend securing them with new oval head screws, part # 99921900800. 2 screws are needed per plate. We also recommend adding new striker plates gaskets, either 90153170323 or 90153170324 depending on what thickness you need. This line is a high-quality replacement part, sourced in Germany and designed to perform like the original. Sold individually. 1 necessary per car.
From $86.63
Make a selection 91135204108EQ If you are experiencing a pulsation and hearing grinding sounds when braking, odds are your rotors need to be replaced to restore full stopping power. This rotor is an OEM replacement (replacement for original #911 352 041 08), manufactured by zimmermann in Germany. It is internally vented and z-coated for corrosion resistance. Features: anti corrosion "z-coating" prevents rust. Simple bolt on, modifications are not necessary. Made in Germany. Sold individually. 2 necessary per car. Left or right-side fitment. Please note: rotors should always be changed in pairs. Please check the model fitment tab to ensure accurate fitment.
$174.41
Make a selection 91511600127 Cast iron pressure plate manufactured by zf sachs to original specifications for all 915 transmissions. Direct replacement for the oe pressure plate. Please note: this is only to be used with sprung discs. We always recommend replacing the pressure plate, clutch disc, throw out bearing and starter ring gear at the same time. View/Change Diagram
From $322.69
Make a selection 91110541550 When working on your cylinder head, we recommend replacing the valves, valve seat rings, guides, springs, retainers and temperature sensor at the same time to reduce future labor costs. High-quality trw OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 6 necessary per car. View/Change Diagram
From $155.93
Make a selection 91110514300 This a genuine part sourced from Porsche ag in Germany to ensure quality, reliability and precise fitment. Professional installation is required. Different manufacturing tolerances require an inspection of the free clearance of all parts! Sold individually. 1 necessary per car. Please note: this camshaft fits 911 models from 1974-77 with engine codes: 911.42/43/44/47/48/48 911.81/82/84/85/86/89 911.90/93/94/98/99 View/Change Diagram
$1,097.25
Make a selection 91110541120OE When working on your cylinder head, we recommend replacing the valves, valve seat rings, guides, springs, retainers and temperature sensor at the same time to reduce future labor costs. High-quality trw OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 6 necessary per car.
$46.20
Make a selection 91110190150 Oem (original equipment manufacturer) complete set of bearings that includes #8, sourced in Germany to ensure quality, reliability and precise fitment. Sold as a set. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment. View/Change Diagram
$689.15
Make a selection 91110190170SET Oem (original equipment manufacturer) complete set of bearings that does not include #8, sourced in Germany to ensure quality, reliability and precise fitment. Sold as a set. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.
$677.99
Make a selection 96414718703EQ Remove the power steering belt cover to inspect your toothed steering belt for wear and cracking. Belts undergo a lot of friction and wear, so replacing them periodically will prevent damage. Be sure to follow recommended service and replacement intervals set by Porsche on belts or examine the power steering pump belt at each oil change. Sold individually. 1 necessary per car.
$71.61
Make a selection 93011115701EQ This cross over connector replaces original part # 930 111 157 01, it is a quality coated steel replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For proper installation, we recommend a new exhaust gasket, part # 93011119307 and sealing ring, part # 91111118903 sold individually. 1 necessary per car.
$61.22
Make a selection 93010776500 The oil thermostat is a critical oil component that regulates the oil temperature. High-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. We also recommend the correct o-ring for installation, part # 99970731440 sold individually. 1 necessary per car. View/Change Diagram
From $175.13
Make a selection 930123002X This remanufactured turbo is a direct replacement for original part # 930 123 002 00. The remanufacturing is completed in Germany by kkk/borg warner certified technicians. This ensures reliability, superior performance and cost effectiveness. The remanufacturing process includes: complete disassembly. All parts are cleaned, inspected and measured for tolerances. Turbine wheels are replaced. Thrust bearings are replaced. All new seals are installed. Internals are reconditioned. Parts are balanced (static & dynamic) according to balancing protocol. For a complete installation we recommend adding a gasket, part # 93012319105 an intake sleeve, part # 93011015801 and be sure to have a few spare studs on hand, part #...(choose a part on the right to read more)
From $3,130.83
Make a selection 915302911161 This ring and pinion is manufactured in Germany to our specifications using case hardened steel (18crnimo7-6). Our specifications include special heat treatment which is extremely wear resistant, contains a tough inner core, includes high tensile strength and exhibits lower noise levels. Sold as a set. 1 necessary per car. Technical info: setting for the drive train is on the bevel gear and not as usual on the ring gear.
$5,679.14
Make a selection 93010090803EQ High-quality victor reinz replacement gaskets, o-rings and washers to reseal your cylinder heads. Victor reinz has been supplying German auto manufacturers and Porsche for decades. They are a trusted name in gaskets and sealing products. This kit is complete with everything needed and we source this directly in Germany for an added level of quality. Sold individually. 1 set necessary per car. To complete the gasket set for the entire engine, also order part # 93010090104eq
$657.20
Make a selection 91530239906EQ Cylindrical roller bearing, located on the pinion shaft, nearest 4th gear and the tensioning plate. High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.
$296.84
Make a selection 90005900300 Tapered roller type this is a replacement tapered roller bearing for the inner side of the early “small†25 mm spindle   it measures:  id 25  and od 62 mm  it’s marked 30305 on the face of the inner ring   tip  -- don’t forget to have a set of front wheel bearings in your emergency travel parts kit Â
$26.29
Make a selection 93010541951EQ When working on your cylinder head, we recommend replacing the valves, valve seat rings, guides, springs, retainers and temperature sensor at the same time to reduce future labor costs. Quality German aftermarket replacement designed to perform like the original. Sold individually. 6 necessary per car.
$51.98
Make a selection 115900991BI02 This bilstein b16 damptronic active coil over suspension kit features ride height and damping adjustability that is compatible with the Porsche pasm electronic damping system. The damptronic system constantly monitors the road surface via sensors, so the vehicle adjusts for perfect traction, unparalleled control and stable handling. Each active Porsche electronic suspension feature, control and setting is retained and all function in the same manner. The front and rear progressive rate springs are matched with bilstein's famous monotube performance dampers. This suspension is custom tuned for the 991.1 and 991.2 variants. The front and rear threaded damper bodies allow .8 - 1.5 inches (20-40 mm) of travel whic...(choose a part on the right to read more)
$5,457.38
Make a selection 930105136001 Genuine gear, sourced in Germany to ensure quality, reliability and precise fitment. We recommend ordering 6 qty. Oil pump lock plates part # 99903900100 for installation. Please note: please check the model fitment tab to ensure accurate fitment. Sold individually. 1 necessary per car.
$421.58
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |