PORSCHE 924 GT CHECK OUTCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1974-77 - Body (includes uncategorized and accessory items) 115910987001 Bilstein b4 OEM (original equipment manufacturer) replacement shock absorber set (4 pieces) for your Porsche with standard suspension (without pasm). The b4 dampers from bilstein are the perfect replacement for your Porsche. Facts: - constant damping power under any load - high power reserves for maximum safety - ride like it's the first time, every time - OEM quality - bilstein gas pressure technology
$1,553.58
Make a selection 115385 If you are looking for added damping performance on the street, the bilstein b6 performance damper is the ideal solution. The product benefits at a glance: optimum adhesion and enhanced stability for daily driving and extreme driving situations. Marked improvement in safety and sportiness without additional spring changes. Increased service life. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Road-tested and fine-tuned by bilstein. German TUV registration is not required. Sold individually. 1 necessary per car. We recommend adding our lowering spring collars if you would like a lower ride height, our part # 115110016
$672.21
Make a selection 99334703104 If your outer tie rods are worn, you will experience sloppy steering response and knocking / creaking sounds. Your outer tie rods keep the steering centered, so failure can be dangerous and can seriously affect steering control. After replacing the tie rods, you will experience tighter, more precise feedback without noise. Tie rod consists of: 1 qty. Tie rod 1 qty. Hexagon nut (m14 x 1.5) 1 qty. Inner axial joint 1 qty. Lock nut 1 qty. Dust bellows / boot we recommend replacing the right and left side tie rods at the same time. Sold individually. 2 necessary per car.
$227.10
Make a selection BES91105000SST This muffler was specifically designed for a backdate to the st look. It is manufactured for mid-range and top end performance, all without drone inside the cabin. It seamlessly mates to ssi heat exchangers for added performance while keeping the cabin warm in the winter. The muffler is vastly different than the common baffle plated mufflers stuffed with packing material that are common in the aftermarket. Ours are uniquely made with double perforated sound absorption tubes based on the halbgegenstromprinzip (half counter current principle). The acoustic silencer absorption tubes are made in a trapezoidal pattern and are perforated with varying diameters, which isolate and dampen the unwanted frequencies that c...(choose a part on the right to read more)
$2,694.62
Make a selection 9A110514203 Timing chains are critical engine components that should be addressed as soon as wear or stretching is noticed. The first indication is typically a misfire, as the timing chain stretches out skips a gear and creates the misfire. Shavings from the timing chain can also be noticed in the filter, around the drain plug or in the oil. The last sign is a rattle at idle and if this is missed serious engine damage can occur if the chain breaks. If you are experiencing any of these signs, replace your chain with this high-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2...(choose a part on the right to read more)
From $321.71
Make a selection 96434705804SP We are committed to Porsche cars and are very happy to release an inner tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 032 00. We also suggest replacing your outer tie rods, part # 96434703200 (qty. 2 are needed) and now is also a good time to replace your worn out inner tie rod dust bellows, part # 96434719103. Please note: this is not for the ...(choose a part on the right to read more)
$206.75
Make a selection BES97005080S11 Brombacher panamera s & 4s "sound version" sport muffler - 10 crank hp & + 9 crank torque. - 2.5'' tubing (63,5mm) straight through design for maximum power. - 11 lb. Weight savings. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - quad 4'' (100mm) round tips sold separately for basic OEM systems (without Porsche sport exhaust)* - tips can be individually adjusted for personal taste. - deeper tonal quality and louder volume which enhances 4.8 l Porsche sound.** - no ecu (software) programming necessary. - will work with OEM exhaust components. - absolutely no drone in the cabin. - does not interfere with emissions and will not trigger the check engine light. - made in Germany...(choose a part on the right to read more)
$2,599.91
Make a selection BES98115001SK This is our jekyll and hyde version ! The perfect compromise for you and your loved ones. Rich, deep race car tones with the valves open and soft subtle, completely stock sounds with them closed. Top of the line or range depending on the english, and is the best choice for a daily driver. + 11 hp & + 10 tq gain. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - 2 1/2 tubing (63.5 mm). - 2 x 3.5 (90 mm) round tips. - intoxicating growl at idle, partial throttle and wide open throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - minimal resonance / drone in the cabin (200 rpms worth) compared t...(choose a part on the right to read more)
$5,457.38
Make a selection BES981C5000SKGT Gt4 clubsport ++ with the valves open. Completely civilized at low rpms and while cruising. + 11 hp & + 10 tq gain. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - 2 3/4 tubing. - 2 x 3.5 (90 mm) round tips. - intoxicating growl at idle, partial throttle and wide open throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - minimal resonance / drone in the cabin. - "aero quip" style motorsport muffler connections to ensure a leak free exhaust. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. Please note: gaskets a...(choose a part on the right to read more)
$5,630.63
Make a selection 96437504381 Replace your worn-out, original soft rubber engine mounts with our higher density, rs specification rubber bushing. This is manufactured of rubber with a 75-shore hardness value. 75-shore is the same density as what is used in the rs models. It is more durable, provides more positive, sharper shifts and offers crisper throttle response. Yet, rs spec rubber is still quiet and comfortable for street use. Features: sharper shifts crisper throttle response does not produce nvh (noise vibration harshness) like teflon or solid bushings rubber has a shore hardness value of 75 (like rs models) made in Germany this mount is a high-quality OEM (original equipment manufacturer) replacement part, designed to perform like t...(choose a part on the right to read more)
From $199.99
Make a selection 96433102100RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$705.71
Make a selection 96453705700SET If you are hearing a crunching or creaking noise when you close your door, start by replacing your door check / door arrester. It prevents the door from opening to widely or slamming. As our cars age, they wear out and start to become very noisy. We also recommend replacing the door check bolt, and safety clip, so we have created an complete set for one door - repair sold individually. Left of right side fitment. 2 needed per car.
$67.35
Make a selection 99334703181 If your tie rod is worn, you will experience sloppy steering response and knocking / creaking sounds. Your tie rod keeps the steering centered, so failure can be dangerous and can seriously affect steering control. After replacing the tie rods, you will experience tighter, more precise feedback without noise. Tie rod consists of: 1 qty. Tie rod 1 qty. Hexagon nut (m14 x 1.5) 1 qty. Inner axial joint 1 qty. Lock nut we recommend replacing the right and left side tie rods at the same time. We also recommend replacing the bellows, part # pcg419831c sold individually. 2 necessary per car.
From $318.15
Make a selection 96410524707GU This fits 964 c2 / c4 and rs models with engine codes # m64.01/02/03. This is an OEM part, sourced directly from Germany. Professional installation is required. Different manufacturing tolerances require an inspection of the free clearance of all parts! If you're not sure about what parts are right for your build, be sure to ask one of our parts specialists. Sold individually. 1 necessary per car.
$979.44
Make a selection 96453109500EQ This is a genuine door seal that seals the entire door and window frame. As these classics age the original gasket can become brittle and will crack, so it is essential that it is in good order as it keeps moisture out of the cabin. Sold individually. 1 necessary per car.
$226.38
Make a selection 96410524609ST This fits 964 c2 / c4 and rs models with engine codes # m64.01/02/03. This is an OEM part, sourced directly from Germany. Professional installation is required. Different manufacturing tolerances require an inspection of the free clearance of all parts! If you're not sure about what parts are right for your build, be sure to ask one of our parts specialists. Sold individually. 1 necessary per car.
$1,513.05
Make a selection FVD3511M39040A2 The brembo gran turismo (gt) braking system with type iii rotors is ideal for ideal for clubsport and sprint type track events. It utilizes brembo type iii aggressive face-type discs that offer high initial response with a smooth pedal feel. The type iii offers the highest overall braking confidence and control, allowing a quick qualifying time or top results in sprint races. The GT line is dedicated to the most demanding customers. It originates from racing components, consisting of floating ventilated cross drilled discs, aluminum calipers with opposed pistons, a complete set of high-performance brake pads, abrasion and corrosion resistant goodridge braided steel brake lines and high-quality fastener hardware...(choose a part on the right to read more)
$5,307.23
Make a selection BES99102240SHDO + 15 hp & + 14 torque - 200 cell high flow, tri metal German hjs "hd" high durability matrix sports catalysts. - can be used with FVD "brombacher" mufflers. - weighs 15.5 lbs. (7.0 kg). - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - made in Germany. - intoxicating growl at idle, partial throttle and wide open throttle. The catalytic converter cores used in this system are the most advanced in the industry. They are produced by hjs in Germany and are a 200 cpsi (cell per square inch) tri-metal design. Tri-metal cats are the freest flowing and environmentally friendly aftermarket cats produced today. Tri-metal catalytic converters are rodium, platinum and iridium coated and per...(choose a part on the right to read more)
$4,602.68
Make a selection BES99120040S Take your 991.1 or 991.2 turbo or turbo s to a new level with these muffler bypass pipes. They produce the wildest sound available on the market today and are a perfect upgrade for level 3 or 4 car used on the track. They produce loud, low, deep tones with exaggerated turbo whistling and sinister gurgling and crackling off throttle. By far the best sound you can get out of your turbo, not to mention being able to shoot flames! The only real drawback is the drone in the cabin which we try to minimalize by stepping down the diameter in 3 stages. Features: - + 35 crank hp & + 25 crank torque - 3 tubing (75mm) that tapers down to 2.25" (57mm) to prevent turbo damage. - weighs 7 lbs. (3,1 kg) - German v2a - x5crni1...(choose a part on the right to read more)
$705.71
Make a selection BES99722040S81 Brombacher 997.2 tt "sport stock" stainless steel, cat bypass for OEM muffler facts: - + 21 crank hp & + 18 crank torque** - reuses OEM muffler, perfect for those looking for more sound and power. - tubing diameter is the same as the OEM system. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - reduces backpressure and thermal stress - 6 on a scale of 1-10 in volume (1 being stock). - reuses OEM v band style connecting hardware. - made in Germany. - available in 100 cell or 200 cell. Please ask your sales person for pricing. - more distinguished growl at idle, partial throttle and wide open throttle. - dme programmin is necessary. - reuses OEM tips. FVD i...(choose a part on the right to read more)
$902.06
Make a selection BES99102240SHD + 15 hp & + 14 torque - 200 cell high flow, tri metal German hjs "hd" high durability matrix sports catalysts. - can be used with FVD "brombacher" mufflers. - weighs 15.5 lbs. (7.0 kg). - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - made in Germany. - intoxicating growl at idle, partial throttle and wide open throttle. The catalytic converter cores used in this system are the most advanced in the industry. They are produced by hjs in Germany and are a 200 cpsi (cell per square inch) tri-metal design. Tri-metal cats are the freest flowing and environmentally friendly aftermarket cats produced today. Tri-metal catalytic converters are rodium, platinum and iridium coated and per...(choose a part on the right to read more)
$3,458.07
Make a selection BES99106041S - 2 3/4 tubing (70mm). - weighs 7 lbs. (3,1 kg). - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - "quad" style tips, inner tip is 3.5" (90 mm) in diameter and outer is 3.4" (88 mm). - polished stainless steel. - made in Germany - will not fit stock mufflers! These tips only work in conjunction with our "brombacher" sport mufflers. Please note: using stock tips on our sport mufflers without these tips will cause hp loss. Once you restrict the diameter of the piping a small percentage of power is robbed. The exhaust tips are a dual 3.5"/ 3.4 round design and are double walled to dissipate heat, which means that they won't tarnish as quickly as single walled tips. There is an ...(choose a part on the right to read more)
$1,389.47
Make a selection BES99105060S - + 12 crank hp & + 12 crank torque - 2 3/4 tubing (70mm) straight through design for max. Power - weighs 18 lbs. (8.5 kg), which is a 3 lbs. Savings off of OEM center muffler. - replaces stock side mufflers and stock center muffler. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - 2 x 3.5 (90mm) round tips. - includes all necessary clamps and mounting brackets. - made in Germany. - intoxicating cup car growl at idle, partial throttle and wide open throttle. - no dme programming necessary, does not alter emissions, 50 state legal in the u.s. Our 991 GT3 center muffler replacements are vastly different than the baffle plated mufflers stuffed with packing that are common in the after...(choose a part on the right to read more)
$2,454.38
Make a selection BES987C0200SHD Brombacher Cayman/s (sound version) stainless steel exhaust system facts: - + 20 crank hp & + 19 crank torque - 200 cell high flow, tri metal German hjs sport catalysts - 2 tubing (50 mm) straight through design for max. Power - weighs 57 lbs. (25,8 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability - dual 3.5 (90mm) round tips - includes quick release clamps - made in Germany - intoxicating growl at idle, partial throttle and wide open throttle - no dme programming necessary. FVD is proud to introduce our newest line of Brombacherexhaust systems. Brombacher exhausts are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredibl...(choose a part on the right to read more)
$8,968.08
Make a selection BES99726000SO FVD is proud to introduce our newest line of Brombacherexhaust systems. Brombacher exhausts are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredible value. All of our exhausts are manufactured in Germany and are tested comprehensively for flow rate and characteristics, thermal stress, resistance to cracking, and longevity. Brombacher mufflers outer shell dampens and eliminates unwanted frequencies and ensures no resonance or drone in the cabin. The end result is a strong, linear, firing-order dominated flat-6 Porsche sound. In addition, Brombacherexhausts systems are available for ultimate performance full titanium. Our titanium system's are nearly...(choose a part on the right to read more)
$1,427.58
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |