Vehicles
Sections
113 not categorized PORSCHE 356A SUSPENSION REARCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1970-73 (includes uncategorized and accessory items) FVD33150005 Restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm cannot compensate enough when lowering your Porsche, leaving you with as much as ½ inch of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration. Sold in pairs. 1 necessary per car.
$825.66
Make a selection FVD33399301 Bilstein suspension featuring with upside/down technology. Lowering 35 mm front and 30 mm rear - giving it a European rs stance
$12,984.84
Make a selection FVD33150020 This kit is complete and includes the front and rear monoball cartridges with press tools. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 4. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$772.20
Make a selection FVD3310212291 Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. It offers rs style handling characteristics, superior durability and is still forgiving enough for street use. - better handling. - makes precision adjustments of the suspension easier. - does not produce road noise. - shore hardness value of 85. - direct OEM replacement. - more forgiving for street use. -includes press tools and grease for easier assembly. Sold as a set. 1 kit is necessary per car. Please note: this fits the 964 c2 / c4 and rs america. Not keen on installing or having the bushings installed at a shop? Please check out our part # FVD33399603b8 and FVD33399603b8, we wil...(choose a part on the right to read more)
$974.16
Make a selection FVD333007 These high quality, German made mounts are made specifically for rear shock absorbers that contain a 15mm i.d. Uniball spherical bearing. They are located at the base of the rear shocks, and secure the shock to the rear trailing arms. They are required with FVD exclusive suspension kits with part #'s 115 900 911 xx / xxx. For example 115900911030 they are also required for rear shocks like part # FVD33315755 sold as a set. 1 necessary per car.
$188.89
Make a selection FVD33398701 Bilstein suspension featuring with upside/down technology. Lowering 35 mm front and 30 mm rear - giving it a GT3 stance.
$3,028.21
Make a selection FVD33399300 A cost effective FVD exclusive combination of bilstein clubsport shocks with a set of TUV certified eibach springs. This suspension kit will lower the front axle to a maximum of 35 mm (1.37 inches) and the rear axle to 30 mm (1.18 inches), like the European rennsport model. The height is adjustable as the dampers are threaded. They are a cost effective solution for clubsport use and will be well mannered on the street. Sold as a complete kit. 1 kit is necessary per car.
$3,323.19
Make a selection FVD33300905 This rear spring plate is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New rs spec. (85 shore) rubber bushings are installed to make this a direct bolt on. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Features: made from ¼ inch spring steel includes new rs spec. (85 shore) rubber bushings made in Germany sold individually. 2 necessary per car.
$295.81
Make a selection FVD33399602B8 Bilstein suspension featuring eibach springs. Lowering 35 mm front and 30 mm rear - giving it a GT3 stance
$2,100.38
Make a selection FVD341999R Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with our FVD clubsport series. They are made from rubber with a 85 shore hardness value which is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This is the ideal upgrade for street and light track / clubsport use. This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes 85 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$134.24
Make a selection FVD721T221 Camber adjuster needed to adjust toe - in of the rear suspension.
$16.63
Make a selection 11599702 Non pasm cars - lowers the front 1.0 inch (25 mm) and the rear 1.0 inch (25 mm). Pasm cars - lowers the front .8 inches (20 mm) and the rear .8 inches (20 mm). Targa - lowers the front 1.3 inches (35 mm) and the rear 1.3 inches (35 mm).
$508.46
Make a selection 11599700H Without pasm cars - lowers the front 1.2 inch (30 mm) and the rear 1.2 inch (30 mm). Pasm cars - lowers the front .8 inches (20 mm) and the rear .8 inches (20 mm).
$554.44
Make a selection 115910996032 Bilstein b4 OEM m030 (original m030 suspension) shock absorber set (4 pieces) for cars with lowering springs or cars delivered with factory m030 sport suspension. Nothing is better than the original! The b4 m030 dampers from bilstein are the perfect shock absorber for lowered cars. Facts: - constant damping pressure under load - increased driving stability - increased durability - OEM quality - bilstein gas pressure technology - type/model m030
$1,817.20
Make a selection FVD33300905ATK Send us your original spring plate and we will have it reconditioned for you. The reconditioning process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and media blast the part. Once fully prepared, we install new rs spec. (85 shore) rubber bushings/bearings. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Then we seal the spring plate with a corrosion resistant plating. Sold individually. 2 necessary per car. Please note: this does not fit cars with the g50 transmission.
$337.39
Make a selection 150SPB976 Replace worn-out spring plate bushings with these longer lasting poly-graphite plastic bushings. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This includes the inner and outer bushing for the 2-piece adjustable spring plate. Sold individually. 2 necessary per car.
$42.77
Make a selection FVD333505002 996 atmospheric cars only with m030 factory sport suspension
$47.52
Make a selection 115910997006 Bilstein b4 OEM i030 (original i030 suspension) shock absorber set (4 pieces) for cars with lowering springs or cars delivered with factory i030 sport suspension. Nothing is better than the original! The b4 i030 dampers from bilstein are the perfect shock absorber for lowered cars. Facts: - constant damping pressure under load - increased driving stability - increased durability - OEM quality - bilstein gas pressure technology - type/model i030
$2,326.29
Make a selection 115910997003 Bilstein b4 OEM i030 with pasm (original i030 suspension) shock absorber set (4 pieces) for cars with lowering springs or cars delivered with factory i030 sport suspension. Nothing is better than the original! The b4 i030 dampers from bilstein are the perfect shock absorber for lowered cars. Facts: - constant damping pressure under load - increased driving stability - increased durability - OEM quality - bilstein gas pressure technology - type/model i030 with pasm
$3,415.21
Make a selection MB1230 The Porsche 911 came equipped from the factory for high performance cornering -- but some things have changed in the almost 40 years the 911 has been on the road. For one, the rubber suspension bushings that monoballs replace are most likely already worn out or cracked from decades of use. General Fitment911 1987-89911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1965-69 912 1965-69
$295.81
Make a selection 99333105180 The bushings are made of rubber with an 85-shore hardness value, which is more durable, provides more positive suspension location and is still quiet and comfortable for street use. Sold individually.
From $825.66
Make a selection FVD33150046R Replace worn-out original soft rubber (65 shore hardness value) track rod bushings with our FVD clubsport series. They are made of rubber that has an 85-shore hardness value, the same as the rs models. 85-shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes an 85-shore hardness value core. Sold individually. 8 are necessary per car. Please note: this does not include the track rod, the picture circled in red is just for reference.
$71.28
Make a selection FVD333505001 Without ( i030 ) sport suspension set contains: - 2 x 993 333 107 01 - 2 x 996 333 105 02 also c4s cabrio with standart suspension
$179.65
Make a selection 99333105280 The bushings are made of rubber with an 85-shore hardness value, which is more durable, provides more positive suspension location and is still quiet and comfortable for street use. Sold individually.
From $825.66
Make a selection FVD34391101SET Replace worn-out original front lower control arm bushings to return your car to its intended suspension geometry and steering feedback. Features: better handling reduces that sloppy steering feel does not produce any noise like the teflon bushings. Rubber has the original shore hardness value of 65 (like oem) fit's like oem, simple installation made in Germany if you are looking for a sportier upgrade we suggest our sport lower control arm set, part # FVD34391192set. Set is sold per axle. 2 necessary per car.
$165.13
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |