Vehicles
Sections
15 not categorized PORSCHE 356 OIL LINE KITCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1965-69 (includes uncategorized and accessory items)
SIC10734800 Due to occasional oil seepage, the right side tensioner oil supply line has been modified, also, both left and right oil line are now installed with an additional bracket on the chain housing cover. This kit includes the updated right supply line, both brackets, clamps & screws. Fits all cars with oil fed tensioners. General Fitment930 1975-77911 1974-77 911 1970-73 911 1965-69 911 1978-83
$112.86
Make a selection FVD211328ANB
$469.26
Make a selection 10010303204 - 3.2 l for increased horsepower and torque.* - genuine mahle forged pistons with deeper valve pockets. - genuine mahle steel (st52) nikasil coated cylinders.** - piston pin bore is off center (deaxiated) for factory quiet operation. - 10.3:1 compression. - 98 mm big bore. - 22x58 racing wrist pins - 70.4 stroke. - made in Germany by mahle gmbh. - piston rings installed directly on the pistons for ease of installation. - complete set with cylinders, pistons, rings, wrist pins and clips. - kit weighs 21.03 lbs. (9.54 kg). Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resista...(choose a part on the right to read more)
$10,468.99
Make a selection 911051 Porsche 911 ac compressor upgrade kit, 1984-89, lh drive model provides improved integrity with our kuehl barrier hose set, kuehl low- high pressure switch to help protect the system, a new denso factory compressor with clutch, new kuehl drier, complete o-ring kit, along with r134a charge port adapters. you can use either r12 or r134a with refrigerant with this complete kit. all barrier hoses match OEM configuration, have sae sae approved crimped fittings and each hose is labeled so you know where it goes.
$1,552.12
Make a selection 915300911550 If you are looking for a transmission oil cooler system that is simple to install, provides lasting results and is perfect for a driver, the weekender, or for track use look no further. This kit includes a sleek high-performance oil cooler that mounts simply to the transmission cover with the included bracket and hardware. The stainless braided lines seamlessly screw into the transmission housing drain / fill plug location, no modification required. The electric, self-priming, 12 v oil pump is made with helical bronze gears, a stainless-steel shaft and a nickel plated brass body for the reliability that you expect from your Porsche. The pump includes a bracket that allows for simple installation. Simply connect...(choose a part on the right to read more)
$1,651.32
Make a selection 10021102900 This heat exchanger is engineered for the discerning Porsche 911 3.2 l owner looking for more performance. These are manufactured in stainless steel. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Features: gains of +10 hp and +10-15 tq stainless steel 1.5" pipe diameter for backpressure reduction 21.5 mm thick flange with "fire ring" connects "early style" dual inlet mufflers bolt on replacement for the left side reduces the ...(choose a part on the right to read more)
$1,470.74
Make a selection 100211025SSUSA If you have a us model 1980-83 911 SC and are looking to replace your heat exchangers we have some good and bad news. The original heat exchangers (part # 930 211 025 02) are no longer available from Porsche. But, these stainless-steel industries (ssi) heat exchangers will work with modifications. The good news is, once done, you will have more torque and horsepower! Free flow conversion heat exchangers improve sound and performance, while reducing backpressure and thermal load on the motor. These are based off the early style exhausts found on the 1974 2.7 l rs. Those models had a straight through, superior, free flow exhaust design that included a dual inlet muffler. When converting to these heat exchangers y...(choose a part on the right to read more)
$3,435.70
Make a selection 100211030SSI This heat exchanger kit is engineered for the discerning Porsche 911 3.2 l owner. Ssi heat exchangers are made from superior t 304 grade (18% cr, 8%+ ni) stainless steel. Ssi has become an industry standard for Porsche 911 heat exchangers due to the exceptional materials, craftsmanship and durability. This is critical when considering heat exchangers, as exhaust leaks caused by poor materials can lead to carbon monoxide entering the cabin via the heating system. Features: gains of +10-15 hp and +10-20 tq t304 stainless steel (18% cr, 8%+ ni) 1.5" pipe diameter for backpressure reduction 21.5 mm thick flange with "fire ring" includes o2 sensor socket connects "early style" dual inlet mufflers bolt on replac...(choose a part on the right to read more)
$3,492.72
Make a selection 911050 Kit includes General Fitment911 1965-69911 1978-83 930 1975-77 911 1974-77 911 1970-73
$827.23
Make a selection 10021103000 This heat exchanger is engineered for the discerning Porsche 911 3.2 l owner looking for more performance. These are manufactured in stainless steel by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Features: gains of +10 hp and +10-15 tq stainless steel 1.5" pipe diameter for backpressure reduction 21.5 mm thick flange with "fire ring" connects "early style" dual inlet mufflers bolt on replacement for the right side re...(choose a part on the right to read more)
$1,913.87
Make a selection BAT006 Many pre. 1977 Porsche 911's are not equipped with factory oil plumbing (hard lines and thermostat). In this case fitting an oil cooler requires making a hose run from the rear to the front of the vehicle and back. We find the easiest and most cost effective method of plumbing is to duplicate the factory plumbing route using aeroquip hose and fittings with a mocal oil thermostat and oil cooler. The various kits that we offer to accomplish this task include; one of a number of oil cooler options (some are suitable for both fender or front spoiler location), mocal -12 an oil thermostat with mounting bracket, 30 foot length of aqp -12 an stainless braid 3/4" id hose, 30mm metric to -12 an adaptors for the oil ta...(choose a part on the right to read more) General Fitment911 1974-77911 1965-69 911 1970-73
$1,273.81
Make a selection 930105911912 If you have an early 911 or 914-6 you can upgrade to the 1984-89 911 Carrera oil pressure fed tensioner system will prevent engine damage from collapsed chain tensioners. The kit includes 2 chain housing covers, 2 oil lines, 2 tensioners, and fittings needed to complete installation. Some special tools required. Call for details. General Fitment911 1965-69911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89 914 1970-76
From $1,185.84
Make a selection FVDIDA46 Complete carburetion kits ! General Fitment911 1965-69911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89
$11,668.60
Make a selection BAT002 Many pre. 1977 Porsche 911's are not equipped with factory oil plumbing (hard lines and thermostat). In this case fitting an oil cooler requires making a hose run from the rear to the front of the vehicle and back. We find the easiest and most cost effective method of plumbing is to duplicate the factory plumbing route using aeroquip hose and fittings with a mocal oil thermostat and oil cooler. The various kits that we offer to accomplish this task include; one of a number of oil cooler options (some are suitable for both fender or front spoiler location), mocal -12 an oil thermostat with mounting bracket, 30 foot length of aqp -12 an stainless braid 3/4" id hose, 30mm metric to -12 an adaptors for the oil ta...(choose a part on the right to read more) General Fitment911 1974-77911 1965-69 911 1970-73
$999.00
Make a selection BAT003 Many pre. 1977 Porsche 911's are not equipped with factory oil plumbing (hard lines and thermostat). In this case fitting an oil cooler requires making a hose run from the rear to the front of the vehicle and back. We find the easiest and most cost effective method of plumbing is to duplicate the factory plumbing route using aeroquip hose and fittings with a mocal oil thermostat and oil cooler. The various kits that we offer to accomplish this task include; one of a number of oil cooler options (some are suitable for both fender or front spoiler location), mocal -12 an oil thermostat with mounting bracket, 30 foot length of aqp -12 an stainless braid 3/4" id hose, 30mm metric to -12 an adaptors for the oil ta...(choose a part on the right to read more) General Fitment911 1974-77911 1965-69 911 1970-73
$1,063.80
Make a selection BAT004 Many pre. 1977 Porsche 911's are not equipped with factory oil plumbing (hard lines and thermostat). In this case fitting an oil cooler requires making a hose run from the rear to the front of the vehicle and back. We find the easiest and most cost effective method of plumbing is to duplicate the factory plumbing route using aeroquip hose and fittings with a mocal oil thermostat and oil cooler. The various kits that we offer to accomplish this task include; one of a number of oil cooler options (some are suitable for both fender or front spoiler location), mocal -12 an oil thermostat with mounting bracket, 30 foot length of aqp -12 an stainless braid 3/4" id hose, 30 mm metric to -12 an adaptors for the oil t...(choose a part on the right to read more) General Fitment911 1974-77911 1965-69 911 1970-73
$1,111.32
Make a selection 935FSUSP This light weight, bolt in kit replaces the factory front suspension arms, cross-member, and rubber bushings when converting to a coil over front suspension system. General Fitment911 1965-69911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89 914 1970-76
$1,998.00
Make a selection 99651290300G2X Rear spoiler only. The carerra aerokit underlines the performance potential and racing origins of the 911 coupe and cabriolet. Includes an aerodynamic nose section with integrated front spoiler, side skirts, GT rear side trim panels and a discreet, fixed rear spoiler with an integrated third brake light. Prices do not include painting and installation.
$8,025.57
Make a selection RESMK911002 This kit is necessary when installing any of our racing / street exhaust systems manufactured by m exhaust gmbh whose part number begins with res 911 or bes 911 kit contains: - modified oil lines - straps - header / heat exchanger gaskets - additional heating hoses - air injection plug
$525.07
Make a selection RESMK911001 This kit is necessary when installing any of our racing / street exhaust systems manufactured by m&m exhaust gmbh whose part number begins with res 911 or bes 911 kit contains: - modified oil lines - straps - header / heat exchanger gaskets
$409.13
Make a selection BAT005 Many pre. 1977 Porsche 911's are not equipped with factory oil plumbing (hard lines and thermostat). In this case fitting an oil cooler requires making a hose run from the rear to the front of the vehicle and back. We find the easiest and most cost effective method of plumbing is to duplicate the factory plumbing route using aeroquip hose and fittings with a mocal oil thermostat and oil cooler. The various kits that we offer to accomplish this task include; one of a number of oil cooler options (some are suitable for both fender or front spoiler location), mocal -12 an oil thermostat with mounting bracket, 30 foot length of aqp -12 an stainless braid 3/4" id hose, 30 mm metric to -12 an adaptors for the oil t...(choose a part on the right to read more) General Fitment911 1974-77911 1965-69 911 1970-73 928 1978-82
$1,177.20
Make a selection BES99722240BES Brombacher 997.2 tt "sport " stainless steel, sport cat converter replacements for our bes- muffler facts: - + 21 crank hp & + 18 crank torque** - 200 cell "hd", tri metal German hjs sport catalysts - tubing diameter is the same as the OEM system. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - reduces backpressure and thermal stress - 5 on a scale of 1-10 in volume (1 being stock). - reuses OEM v band style connecting hardware. - made in Germany. - available in 100 cell and cat bypass. Please ask your sales person for pricing. - more distinguished growl at idle, partial throttle and wide open throttle. - dme programming not necessary. - reuses OEM ti...(choose a part on the right to read more)
$4,647.46
Make a selection 901107710S Manufactured by the original supplier for Porsche, this three piece oil line kit instantly solves the long search for th e proper oil lines for your six.
$543.78
Make a selection
© 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |