Vehicles
Sections
258 not categorized PORSCHE 356A REAR KITCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1965-69 (includes uncategorized and accessory items) FVD33150005 Restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm cannot compensate enough when lowering your Porsche, leaving you with as much as ½ inch of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration. Sold in pairs. 1 necessary per car.
$825.66
Make a selection ER2071600 Elephant racing low-friction control arm mounts allow for free control arm movement, eliminating any potential for binding. Elephant racing corrected a key factory design limitation:our mounts self-align in all axis, becoming collinear to avoid binding as the arm moves through its range of motion. The low-friction control arm mounts self-align in both the horizontal and vertical planes. The result is collinear front and rear mounts delivering smooth non-binding action. You get superior performance and a smoother ride. Kit includes everything required to upgrade one car. Factory rear mounts are replaced with our self-aligning mounts. Factory front mounts are retained and augmented with self-aligning washers. ...(choose a part on the right to read more) General Fitment911 1965-69911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 914 1970-76 912 1965-69
$243.00
Make a selection ER2290002 Diy kit - rear 914 control arm rubber bushings are now available as a kit for self-installation. in addition to a complete set of 4 OEM spec rubber bushings, the kit includes proprietary installation tools and instructions, which are essential for successful installation plus the rear control arm shafts use a pipe clamp or shop press to complete the install. General Fitment914 1970-76911 1965-69 911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89
$475.19
Make a selection FVD911503185186 This seal kit consists of original part # 911 503 185 00 (left) and 911 503 186 00 (right). The set can be used on the trailing edge of the front fender at the cowl just below the windshield. It is also used under the back of the rear quarter panel where it meets the bumper side panel. Genuine part sourced from Porsche ag in Germany to ensure quality, reliability and precise fitment. Sold as a set. 1 set is necessary for front fenders and one set is necessary for the rear. Please note: this is the thinner width. This is not the thicker width from the SC models.
$16.12
Make a selection FVD35199615B Wheel spacers make your tires and wheels appear wider by moving the wheel out from the hub, providing both performance and appearance improvements. Whether you want improved handling, increase safety, or simply desire your car to make a statement about your individual style, wheel spacers can help you accomplish your goal. FVD BrombacherGermany conveniently combines Porsche specific h&r spacers, the correct Porsche bolt shoulders and the correct length h&r bolts to take the guess work out of adding spacers to your car. Our spacers are cost competitive and have been developed to work together without compromise. Don't be fooled by the competition whose costs quickly add up by requiring you to order the spacers...(choose a part on the right to read more)
$124.74
Make a selection 100555111NB This is a rear carpet kit for a rs model or a rs tribute, without back seats. This set is a lightweight fine German velour that is trimmed in vinyl. Each is cut, sewn and trimmed to fit perfectly. We can also add special order script on the rear deck, just contact us and let us know what you have in mind. Made in Germany. Sold as a set. 1 necessary per car.
$773.39
Make a selection 99135294881 High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold as a rear set. 1 necessary per car. Please note: we also sell a complete kit with sensors, part # FVDbs352991005
From $384.21
Make a selection BAT006 Many pre. 1977 Porsche 911's are not equipped with factory oil plumbing (hard lines and thermostat). In this case fitting an oil cooler requires making a hose run from the rear to the front of the vehicle and back. We find the easiest and most cost effective method of plumbing is to duplicate the factory plumbing route using aeroquip hose and fittings with a mocal oil thermostat and oil cooler. The various kits that we offer to accomplish this task include; one of a number of oil cooler options (some are suitable for both fender or front spoiler location), mocal -12 an oil thermostat with mounting bracket, 30 foot length of aqp -12 an stainless braid 3/4" id hose, 30mm metric to -12 an adaptors for the oil ta...(choose a part on the right to read more) General Fitment911 1974-77911 1965-69 911 1970-73
$1,273.81
Make a selection 115900993BI The bilstein b16 (pss10) suspension kit is the ultimate race inspired suspension system, delivering unsurpassed driving performance in any situation. This suspension kit puts you in complete control, providing the kind of precise suspension tuning formerly available only on race cars. From a weekend of competition to daily driving, this system provides perfect handling performance for every situation. The manually adjustable damping mono-tube gas shock absorbers feature 10-stage precise compression and rebound settings, from comfort to competition. The bilstein b16 (pss10) suspension kit utilizes debris resistant round threads on these dampers to ensure spring adjustment remains effortless throughout the life o...(choose a part on the right to read more)
$4,689.04
Make a selection 115900964BI01 Bilstein b16 (pss10) suspension kits feature ride height adjustability with 10-stage manually adjustable dampers. Simply adjust compression and rebound settings, from comfort to competition, by rotating the setting number knob at the base of the shock. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Ride height is adjustable from 1.0 to -1.5 20-40mm (front) & -1.0 to -1.5 20-40mm (rear - minimum 1 lowering). Bilstein b16 (pss10) suspension allows you to enjoy the kind of precise suspension tuning formerly available only on race cars. We recommend purchasing our lowering collar kit if you plan to run the...(choose a part on the right to read more)
$4,163.94
Make a selection 115900993B12 If you're looking for the perfect combination of sporty dynamics, a superior appearance and high performance, you're on exactly the right track with this sport suspension. This kit is a direct replacement for the factory mo33 kit and will give you the same performance characteristics. -professional cornering system pcs -precise response, excellent driving performance and high reserves of safety -lowering up to 10 - 15 mm in front and rear -eibach pro-kit performance springs with progressive characteristic -springs and shock absorbers road-tested and fine-tuned to complement one other perfectly -bilstein gas pressure technology -bilstein mono-tube/upside-down technology, made in Germany -German TUV certificate...(choose a part on the right to read more)
$2,439.06
Make a selection 115900991BI02 This bilstein b16 damptronic active coil over suspension kit features ride height and damping adjustability that is compatible with the Porsche pasm electronic damping system. The damptronic system constantly monitors the road surface via sensors, so the vehicle adjusts for perfect traction, unparalleled control and stable handling. Each active Porsche electronic suspension feature, control and setting is retained and all function in the same manner. The front and rear progressive rate springs are matched with bilstein's famous monotube performance dampers. This suspension is custom tuned for the 991.1 and 991.2 variants. The front and rear threaded damper bodies allow .8 - 1.5 inches (20-40 mm) of travel whic...(choose a part on the right to read more)
$5,613.30
Make a selection 100555110NFB This is a rear lightweight carpet kit for a rs model or a rs tribute, without back seats. This set is made from German nadel filz. We go to extra lengths to ensure that our carpets are made as closely to the originals as possible. Each is cut, sewn and trimmed to fit perfectly. Details: German nadel filz (needle felt) trimmed in vinyl made in Germany custom made to order sold as a set. 1 necessary per car. Please note: when placing your order, we require the year, model and a list of any interior upgrades like roll bars, etc. This kit is custom made to order.
$1,184.44
Make a selection 115900996BI02 Now you can enjoy the kind of precise suspension tuning formerly available only on race cars. The pss 10 suspension kit provides the ultimate in performance tuning. The fully adjustable monotube gas shock absorbers offer a selection of nine precise compression and rebound settings, from comfort to competition. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Handling and control are just a few twists away.
$4,503.71
Make a selection 115900997BIT021 The pss 10 suspension kit provides the ultimate in performance tuning. The fully adjustable monotube gas shock absorbers offer a selection of nine precise compression and rebound settings. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Handling and control are just a few twists away. Regardless of whether in daily motoring, on the nordschleife of the nurburgring at the weekend, in training courses or in club sports - it's all pure driving enjoyment! Product advantages at a glance: • bilstein mono-tube/inverted technology • bilstein road tested and tuned • high driving dynamics with g...(choose a part on the right to read more)
$4,692.60
Make a selection 115900996BI01 Now you can enjoy the kind of precise suspension tuning formerly available only on race cars. The pss 10 suspension kit provides the ultimate in performance tuning. The fully adjustable monotube gas shock absorbers offer a selection of nine precise compression and rebound settings, from comfort to competition. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Handling and control are just a few twists away.
$4,163.94
Make a selection 115900997BI Now you can enjoy the kind of precise suspension tuning formerly available only on race cars. The pss 9 suspension kit provides the ultimate in performance tuning. The fully adjustable monotube gas shock absorbers offer a selection of nine precise compression and rebound settings, from comfort to competition. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Handling and control are just a few twists away. *** these pss9's are for models without Porsche active suspension management***
$4,228.09
Make a selection BAT004 Many pre. 1977 Porsche 911's are not equipped with factory oil plumbing (hard lines and thermostat). In this case fitting an oil cooler requires making a hose run from the rear to the front of the vehicle and back. We find the easiest and most cost effective method of plumbing is to duplicate the factory plumbing route using aeroquip hose and fittings with a mocal oil thermostat and oil cooler. The various kits that we offer to accomplish this task include; one of a number of oil cooler options (some are suitable for both fender or front spoiler location), mocal -12 an oil thermostat with mounting bracket, 30 foot length of aqp -12 an stainless braid 3/4" id hose, 30 mm metric to -12 an adaptors for the oil t...(choose a part on the right to read more) General Fitment911 1974-77911 1965-69 911 1970-73
$1,111.32
Make a selection BBI9964010004 Features
$858.60
Make a selection 90154591220 Chrome window trim pits, flakes and rusts with time. Don't let it detract from your cars appearance. Replace it with this genuine Porsche part sourced in Germany to ensure quality, reliability and precise fitment. We also recommend replacing entire window trim to achieve a consistent trim appearance. We sell a complete kit for the rear, part # FVD545911000 and for the front, part # FVD541911000 sold individually. 1 necessary per car. View/Change Diagram
From $75.60
Make a selection 99651290300G2X Rear spoiler only. The carerra aerokit underlines the performance potential and racing origins of the 911 coupe and cabriolet. Includes an aerodynamic nose section with integrated front spoiler, side skirts, GT rear side trim panels and a discreet, fixed rear spoiler with an integrated third brake light. Prices do not include painting and installation.
$8,025.57
Make a selection 11595B00HR Lowering up 40mm, front axle load 1290kg / 1340kg rear
$664.09
Make a selection 115993S Lowers the ride height by 35 mm (1.4 inches) in the front and 30 mm ( 1.3 inches) in the rear - like European m030. H&r sport springs are the ideal solution for the enthusiast who appreciates race-bred components designed for street use. Product benefits: sporty appearance improved handling characteristics lowered center of gravity linear or progressive spring design compatible with oe and aftermarket shock absorbers powder coated (purple) for anhanced appearance and corrosion resistance delivered with TUV approval engineered, manufactured and tested in Germany
$627.26
Make a selection 115993S1 Lowers the ride height by 30 mm (1.2 inches) in the front and 30 mm ( 1.2 inches) in the rear.
$716.36
Make a selection 90135296411 Does your car pull to one side when you hit the brakes or let go of the wheel? Do you notice one wheel seems to "get hot"? Are your calipers leaking or stuck even though you have cracked the bleeder nipples? You may need to rebuild your caliper(s). These factory kits include seals, piston clips, and boots; and with a little labor and paint, will look new as well. Reasonably priced, they sure beat the price of a new caliper! View/Change Diagram
From $18.90
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |