Vehicles
Sections
319 not categorized PORSCHE 356 B WE NEED A CARCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1965-69 (includes uncategorized and accessory items) 210111011D1 Improve sound and performance by decreasing exhaust backpressure with this catalytic bypass pipe. This is a painted steel bypass pipe, manufactured by dansk. They offer a complete line of tuning and performance parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment manufacturers (oem) to Porsche in Germany. - + 10 crank hp. - lower, deeper, more exotic exhaust note. - steel coated with high temperature paint. - made in europe by dansk. - reduces back pressure and thermal load on the engine. - includes o2 sensor bung....(choose a part on the right to read more)
$306.90
Make a selection 115500325RSRGO German made quality reproduction of the original rsr front strut brace. The provided strut tower brackets must be drilled to accept the cross bar and welded into position. Sold individually. 1 necessary per car.
$280.48
Make a selection 115900997BIT021 The pss 10 suspension kit provides the ultimate in performance tuning. The fully adjustable monotube gas shock absorbers offer a selection of nine precise compression and rebound settings. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Handling and control are just a few twists away. Regardless of whether in daily motoring, on the nordschleife of the nurburgring at the weekend, in training courses or in club sports - it's all pure driving enjoyment! Product advantages at a glance: • bilstein mono-tube/inverted technology • bilstein road tested and tuned • high driving dynamics with g...(choose a part on the right to read more)
$4,345.00
Make a selection 115900944018CS Sports suspension for 924 - 944 - 968 only for 18mm spring strut mounting this sports suspension is for everyday use and increase the dynamic and response. The lowering is adjustable (30-70mm front and 30-60mm rear). By using springs at the rear axle instead of torsion bars you improve extreme the handling of your car. By removing the rear torsion bars is the weight saving approximately 25kg.
$3,132.80
Make a selection 115900997BIT011 The pss 10 suspension kit provides the ultimate in performance tuning. The fully adjustable monotube gas shock absorbers offer a selection of nine precise compression and rebound settings. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Handling and control are just a few twists away. Regardless of whether in daily motoring, on the nordschleife of the nurburgring at the weekend, in training courses or in club sports - it's all pure driving enjoyment! Product advantages at a glance: • bilstein mono-tube/inverted technology • bilstein road tested and tuned • high driving dynamics with g...(choose a part on the right to read more)
$4,345.00
Make a selection 115900997BI01 Bilstein b16 damptronic not only engine performance but, above all, suspension technology contributes to the fascination of a Porsche sports car. Bilstein offers an range of active coil over systems of the current Porsche models with pasm. The coil over system is electronically adjustable. So pasm-function and car sensors like psm stays fully in function. In addition the height-adjustment offers a certified range of lowering. Discreet sporty looks and precisely defined response within both setup modes, accompanied by high driving dynamics and excellent residual ride comfort. Regardless of whether in daily motoring, on the nordschleife of the nurburgring at the weekend, in training courses or in club sports - it...(choose a part on the right to read more)
$4,667.30
Make a selection 115910997003 Bilstein b4 OEM i030 with pasm (original i030 suspension) shock absorber set (4 pieces) for cars with lowering springs or cars delivered with factory i030 sport suspension. Nothing is better than the original! The b4 i030 dampers from bilstein are the perfect shock absorber for lowered cars. Facts: - constant damping pressure under load - increased driving stability - increased durability - OEM quality - bilstein gas pressure technology - type/model i030 with pasm
$2,983.38
Make a selection 115910996031 Bilstein b4 OEM m030 (original m030 suspension) shock absorber set (4 pieces) for cars with lowering springs or cars delivered with factory m030 sport suspension. Nothing is better than the original! The b4 m030 dampers from bilstein are the perfect shock absorber for lowered cars. Facts: - constant damping pressure under load - increased driving stability - increased durability - OEM quality - bilstein gas pressure technology - type/model m030
$1,682.59
Make a selection 115910996033 Bilstein b4 OEM m030 (original m030 suspension) shock absorber set (4 pieces) for cars with lowering springs or cars delivered with factory m030 sport suspension. Nothing is better than the original! The b4 m030 dampers from bilstein are the perfect shock absorber for lowered cars. Facts: - constant damping pressure under load - increased driving stability - increased durability - OEM quality - bilstein gas pressure technology - type/model m030
$1,784.11
Make a selection 115910997002 Bilstein b4 OEM i030 (original i030 suspension) shock absorber set (4 pieces) for cars with lowering springs or cars delivered with factory i030 sport suspension. Nothing is better than the original! The b4 i030 dampers from bilstein are the perfect shock absorber for lowered cars. Facts: - constant damping pressure under load - increased driving stability - increased durability - OEM quality - bilstein gas pressure technology - type/model i030
$2,476.20
Make a selection 12837001R Stoptech recognizes that great brakes need to look as good as they perform. Performance wheels and tires are best complemented with stoptech sportstop cross-drilled or drilled+slotted rotors.every sportstop brake rotor is produced from a high quality centric parts blank casting and finished in a durable e-coating for corrosion resistance. Sportstop drilled and slotted brake rotors (prefix 127) prevent glazing of the pads, add bite and improve wet and dry braking performance.every sportstop rotor is finished with black e-coating on both sides of the hat, inside the the cooling vanes, and on the outside edge. E-coating is a superior electro-statically applied finish designed to withstand 400 hours of salt water e...(choose a part on the right to read more) General Fitment911 1965-69911 1970-73 911 1974-77 911 1978-83 914 1970-76 924 1976-79 924 1986-88 924 1980-85 944 1982-85 944 1985-88
$186.94
Make a selection 115900997BIGT3D Bilstein b16 damptronic not only engine performance but, above all, suspension technology contributes to the fascination of a Porsche sports car. Bilstein offers an range of active coil over systems of the current Porsche models with pasm. The coil over system is electronically adjustable. So pasm-function and car sensors like psm stays fully in function. In addition the height-adjustment offers a certified range of lowering. Discreet sporty looks and precisely defined response within both setup modes, accompanied by high driving dynamics and excellent residual ride comfort. Regardless of whether in daily motoring, on the nordschleife of the nurburgring at the weekend, in training courses or in club sports - it...(choose a part on the right to read more)
$5,330.60
Make a selection 150CD3898 A great new way to keep your Porsche looking sparkling clean without washing as often. This specially treated soft duster will not scratch paint, yet frequent use will remove dust and dirt without water. A quick once-over with the car duster just before putting your cover on will keep your car and cover a lot cleaner.
$103.40
Make a selection 21011123 Catalytic bypass pipe "x torque" design made by m&m in Germany. The x torque design in is a true x pipe design. It is open in the center to add backpressure for torque. Give's you 10-15 ft-lbs of torque in the mid range along with 10-15 hp in the higher rpms. Why settle for the traditional cross over cat design when you can add torque in the mid range where the 996's need it most! Dme programming is necessary. Without it you will get a check engine light (cel). Tech tip: for older cars repair-kit FVD mk 996300
From $764.50
Make a selection 150BP264 Book description: publication date: january 15, 1999 inside this manual you will find routine maintenance, tune-up procedures, engine repair, cooling and heating, air conditioning, fuel and exhaust, emissions control, ignition, brakes, suspension and steering, electrical systems, and wiring diagrams.
$108.90
Make a selection 1867A For over thirty years, the ignitor has proven itself in applications ranging from race cars to tractors. The ignitor replaces breaker point and troublesome factory electronic ignitions with a dependable, self contained and maintenance free electronic ignition system. The ignitor has been called the “stealth” ignition because of its quick installation and nearly undetectable presence under your distributor cap. General Fitment911 1965-69930 1975-77 911 1974-77 911 1970-73
$173.25
Make a selection 150TB2129 High-performance, direct replacement torsion bar set that allow you to dial in the correct spring rate for street or track use. Features: manufactured from aircraft grade, 4340 alloy steel heat treated for increased strength and durability powder coated to resist corrosion consistent outside diameter and rate for consistent spring rate made in the usa by sway-a-way sold as a set. 1 necessary per axle.
$603.90
Make a selection 22011098100 FVD Brombacherhas a long tradition of offering high quality, extensively tested, easily installed tuning products that offer proven performance. Those high standards naturally led us to the innovative pro design (ipd) plenum product. The ipd patented cast aluminum intake plenum with the larger 82 mm (gt3) throttle body (competition plenum) increases horsepower and torque by optimizing and increasing airflow into the intake manifold. But in order to capitalize on all the performance gains the ipd competition plenum can deliver, you must strike a balance with exhaust components and software. You cannot simply add the ipd competition plenum on the 981 series and expect large gains. But, no need to worry, the FVD ...(choose a part on the right to read more)
$1,529.00
Make a selection 21011196402 Say good bye to the days of having to weld and cut aftermarket sport cats to make them fit! We have our sport cats made in Germany to our specifications and that means that these are 100% bolt on without issue! - + 10 crank hp & +6 crank torque. - 200 cell, tri metallic German hjs sport catalysts. - large volume o 105 mm (4.1 inch diameter) high flow cat. - exhaust hanger brackets are included so that the heat shield does not have to be removed. - weighs 7.2 lbs. (3,2 kg). - direct bolt on replacement. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - reduces backpressure and thermal stress. - made in Germany. - more distinguished flat 6 growl at wide open throttle. The FVD 200 cell...(choose a part on the right to read more)
$1,593.90
Make a selection 22011090102ATK Sport throttle bodies are a great addition for those with highly modified cars. They are a great addition for those with full exhaust systems (larger diameters), maf kits, larger displacements, street or race cams, etc. The remanufacturing process includes full inspection of your throttle body to ensure proper operation after the remanufacturing process. We then disassemble and bore the original to a 2.7-inch (70.5 mm) diameter. The entire throttle body is cleaned, degreased and the internals are polished to create more laminar flow. We then machine the shaft to accept larger butterfly's which seamlessly match the bore. All clearances are checked for precision to ensure reliability. Each throttle body is reman...(choose a part on the right to read more)
$589.60
Make a selection 21011125PSE Only for vehicles with Porsche standard sports exhaust system 200 cell, hjs tri-metal, hf (high flow) hjs catalytic cores with "u-torque" design, manufactured by m in Germany. The u-torque design compensates for the backpressure loss while running the high flow cats. The design minimizes the loss of low end torque and adds 10-15 ft-lbs of torque in the mid and top range of the rpms. Why settle for the traditional cross over cat design when you can add more torque in the mid-range and minimize the loss of torque down low where the 997's need it most! Please note: these fit the OEM mufflers and Porsche sport exhaust (pse) mufflers. Tech tip:add one of our installation kits FVD mk 997300
$3,311.00
Make a selection 22011099706 The 997 turbo ipd "y" pipe was built for the more demanding turbo performance customer. The factory y pipe becomes restrictive when adding substantial power gains. The ipd "y" pipe has larger inlets and an optimized diversion area allowing for even greater power gains. This superior and more efficient design flows 126 more cfm than the factory y pipe delivering the additional power needed to raise the performance bar on any turbo. The ipd "y" y pipe is designed to be a direct replacement of the factory OEM y pipe. There are no modifications or fabrication required for installing the ipd y pipe. This is an easy and straight forward r & r (remove and reinstall) bolt on upgrade. Note: contains everything nec...(choose a part on the right to read more)
$1,094.50
Make a selection 220110932ATK Sport throttle bodies are a great addition for those with highly modified cars. They are a great addition for those with full exhaust systems (larger diameters), maf kits, larger displacements, street or race cams, etc. The remanufacturing process includes full inspection of your throttle body to ensure proper operation after the remanufacturing process. We then disassemble and bore the original 2.4-inch (63 mm) to a 2.6-inch (66.5 mm) diameter. The entire throttle body is cleaned, degreased and the internals are polished to create more laminar flow. We then machine the shaft to accept larger butterfly's which seamlessly match the bore. All clearances are checked for precision to ensure reliability. FVD thrott...(choose a part on the right to read more)
$485.10
Make a selection 91153170102 As a striker plate ages, it will start to rattle and can potentially be a safety risk. We recommend securing them with new oval head screws, part # 99921900800. 2 screws are needed per plate. We also recommend adding new striker plates gaskets, either 90153170323 or 90153170324 depending on what thickness you need. This line is a high-quality replacement part, sourced in Germany and designed to perform like the original. Sold individually. 1 necessary per car.
From $86.63
Make a selection 240600102 Waterproof cloth tape for reliable sealing, masking or concealing of racing fender benders. High initial tack and extremely good adhesion. Pe coated cloth tape, waterproofed. Excellent for repairs, crafting and fixing. Extra strong adhesion, which also allows installation on uneven surfaces. 50 mm wide x 50 meters long.
$18.70
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |