PORSCHE 993 REAR LEDCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1965-69 - Front Axle/Steering (includes uncategorized and accessory items) 150PB100918 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$44.00
Make a selection 150PB1027 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's 911 models from 1978-89 if fitted with an 18mm original rear sway bar.
$49.50
Make a selection FVD911503185186 This seal kit consists of original part # 911 503 185 00 (left) and 911 503 186 00 (right). The set can be used on the trailing edge of the front fender at the cowl just below the windshield. It is also used under the back of the rear quarter panel where it meets the bumper side panel. Genuine part sourced from Porsche ag in Germany to ensure quality, reliability and precise fitment. Sold as a set. 1 set is necessary for front fenders and one set is necessary for the rear. Please note: this is the thinner width. This is not the thicker width from the SC models.
$14.93
Make a selection FVD98661810MG Genuine: engine - 6 cylinder boxer capacity - 2480ccm compression ratio - 11,0:1 max. Power - 150kw (204hp) @ 6000rpm max. Torque - 245nm (181lbf ft) @ 4500rpm max. Speed - 240km/h max. Rpm - 6700rpm acceleration 0-100km/h - 6.9s tuning: max. Power - 158kw (215hp) @ 6000rpm max. Torque - 260nm (192lbf ft) @ 4500rpm max. Speed - 247km/h max. Rpm - 6900rpm acceleration 0-100km/h - 6.7s very important note: our tool can only flash ecu's with the Bosch # 0 261 204 605. If your ecu does not have this Bosch # then the ecu must be sent to us to be flashed in house. Please check the sticker on the outside of your ecu to determine which Bosch # you have. You can check by opening the rear trunk and pulling the carpet li...(choose a part on the right to read more)
$984.50
Make a selection FVD803993VR0222 High quality, German made three-point replacement safety belt, designed to perform like the original. Features / specs: belt length: 300 cm (118 inches) 3 point inertia reel belt angle adjustable reel (max. Of 8 *) includes 22 cm (8.5 inch) buckle, installation hardware and caps. Din-en-iso 9001: 2000 quality standard manufactured, e-mark approved. The matching rear belt is part # FVD803993hr sold individually. 2 necessary per car.
$187.00
Make a selection 1588501000 Originally published by floyd clymer this is a faithful reproduction of the 1967 publication of that manual. Includes complete technical data, service and maintenance information and comprehensive detailed instructions for the repair and overhaul of all major and minor mechanical and electrical components. Covers the Porsche 356-356a-356b-356c series from 1948 through 1965, making it an invaluable resource for collectors and restorers of these classic automobiles. There are separate sections that deal with the repair and overhaul procedures for the engine, ignition system, fuel system, clutch, transmission, rear suspension, steering, front suspension, brakes, shocks, heater and exhaust plus a detailed electrica...(choose a part on the right to read more) General FitmentACCESSORY
$45.50
Make a selection 90151107321 This is the rear release cable for the rear engine deck lid. It is 1900 mm in length. When replacing this cable, we also recommend replacing the handle, part # 90155281320 and the grommet, part # 91151253100. Also, check your rear lid lower lock, part # 90151205200, perfect time to replace it if it is corroded and the spring is worn. Sold individually. 1 necessary per car.
From $9.50
Make a selection 90133300309B This rear spring plate is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New OEM spec. (65 shore) rubber bushings are installed to make this a direct bolt on. Features: made from ¼ inch spring steel includes new OEM spec. (65 shore) rubber bushings made in Germany sold individually. Left or right-side fitment. 2 necessary per car.
$306.90
Make a selection 11595B00HR Lowering up 40mm, front axle load 1290kg / 1340kg rear
$614.90
Make a selection 11599700H Without pasm cars - lowers the front 1.2 inch (30 mm) and the rear 1.2 inch (30 mm). Pasm cars - lowers the front .8 inches (20 mm) and the rear .8 inches (20 mm).
$513.37
Make a selection 115900993B12 If you're looking for the perfect combination of sporty dynamics, a superior appearance and high performance, you're on exactly the right track with this sport suspension. This kit is a direct replacement for the factory mo33 kit and will give you the same performance characteristics. -professional cornering system pcs -precise response, excellent driving performance and high reserves of safety -lowering up to 10 - 15 mm in front and rear -eibach pro-kit performance springs with progressive characteristic -springs and shock absorbers road-tested and fine-tuned to complement one other perfectly -bilstein gas pressure technology -bilstein mono-tube/upside-down technology, made in Germany -German TUV certificate...(choose a part on the right to read more)
$2,258.33
Make a selection 115993S Lowers the ride height by 35 mm (1.4 inches) in the front and 30 mm ( 1.3 inches) in the rear - like European m030. H&r sport springs are the ideal solution for the enthusiast who appreciates race-bred components designed for street use. Product benefits: sporty appearance improved handling characteristics lowered center of gravity linear or progressive spring design compatible with oe and aftermarket shock absorbers powder coated (purple) for anhanced appearance and corrosion resistance delivered with TUV approval engineered, manufactured and tested in Germany
$580.80
Make a selection BES99126090S Our exhaust products are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredible value. Our entire "brombacher" line of exhausts is manufactured by m&m exhaust, gmbh in Germany who is no stranger to Porsche racing exhausts. Each is tested comprehensively for flow rate, thermal stress, resistance to cracking, and longevity. To further ensure quality, m&m use lightweight, motorsports grade, t 316 stainless steel and motorsports grade carbon. Features: inner 3.5" (90 mm) polished stainless-steel tip with FVD logo outer 3.9" (100 mm) matte carbon surround includes clamps for complete installation fills the factory cut outs perfectly can be adjusted for r...(choose a part on the right to read more)
$856.90
Make a selection 911051 Porsche 911 ac compressor upgrade kit, 1984-89, lh drive model provides improved integrity with our kuehl barrier hose set, kuehl low- high pressure switch to help protect the system, a new denso factory compressor with clutch, new kuehl drier, complete o-ring kit, along with r134a charge port adapters. you can use either r12 or r134a with refrigerant with this complete kit. all barrier hoses match OEM configuration, have sae sae approved crimped fittings and each hose is labeled so you know where it goes.
$1,097.00
Make a selection 91163195100EQ Don't let a cracked or faded lens detract from your cars appearance. Replace it with this high-quality OEM replacement, designed to perform like the original. This was genuine equipment on usa models but really cleans up the rear when added in place of the amber look. Quality replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Sold individually. Driver's side fitment. 1 necessary per car. Lookin...(choose a part on the right to read more)
$90.20
Make a selection 91150306203EQRB Without door post without rear lamp holder but: what you need for most quarter panel body repairs!
$1,654.40
Make a selection 91150411302EQ This one-piece seal is furthest from the rear bumper, we recommend replacing this when removing the motor for maintenance. We recommend replacing both the small and large engine seals, the large is part # 91150411102 sold individually. 1 necessary per car.
$16.50
Make a selection 911561053003EQ Rear window cabrio top section, manufactured in Germany with original sonnenland material. It is as close to the original as possible and is cut and trimmed to fit perfectly. Sonnenland material consists of 3 layers, dyed acrylic twill weave top layer, elastomeric rubber inner layer and polyester woven base layer. It provides increased strength against abrasion, increased fade resistance and the tighter woven layers for the mechanically operated tops. Sonnenland high quality material was originally used by Porsche and other top German manufacturers. Made in Germany. Sold individually. 1 necessary per car.
$984.50
Make a selection 91163194000EQ If you are restoring or replacing a rear taillight, you may want to consider this. It is a lightweight, high-quality OEM replacement, designed to perform like the original. Perfect for a race application, or for a lightweight street car. Quality replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Sold individually. Passenger's side fitment. 1 necessary per car.
$320.10
Make a selection 96454303602 Necessary when replacing your right rear quarter window, as this seal retains the window in the body and prevents moisture from getting in. For 964 coupe models. Sold individually. 1 needed per car. Passenger's side fitment.
From $89.00
Make a selection 96433102200RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$672.10
Make a selection 96410601402EQ This OEM cover sits low nearest the rear bumper. If you are removing the motor for maintenance, be sure to check and replace the engine covers / heat shields as necessary. We recommend purchasing a new seal, part # 96410622301 and plug, part # 96410623701 to complete the installation. Sold individually. 1 necessary per car.
$601.70
Make a selection 93035204601EQ The zimmermann OEM brake disc combines high-quality cast materials, a vented and perforated braking surface and includes z-coating. Features: better wet braking performance by permanent expulsion of brake dust and water. Sporty look. Anti corrosion "z-coating" prevents rust. Noticeable improvement in braking performance. Countersunk holes double as wear indicator. Simple bolt on, modifications are not necessary. Made in Germany. Sold individually. 1 necessary per car. Rotors should always be changed in pairs; the rear left is part # 93035204501eq
$237.60
Make a selection 91163195200EQ Don't let a cracked or faded lens detract from your cars appearance. Replace it with this high-quality OEM replacement, designed to perform like the original. This was genuine equipment on usa models but really cleans up the rear when added in place of the amber look. Quality replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Sold individually. Passenger's side fitment. 1 necessary per car. Loo...(choose a part on the right to read more)
$90.20
Make a selection AP9972TT170 The stock exhaust of the Porsche 997.2 turbo is very restrictive compared to aftermarket systems. Porsche does this to meet sound and emission purposes like most OEM manufacturers. agency power set out to create an exhaust system for the new Porsche 997.2 turbo 6speed or pdk that did not drone, would produced amazing performance, and under throttle give an incredible sound. we have accomplished this! the new agency power exhaust not only saves about 30lbs off the rear end, it also improves power quite a bit.
$3,749.95
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |