Vehicles
Sections
183 not categorized PORSCHE 914 INST RINGCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 356 1960-65 (includes uncategorized and accessory items) 96434101707AT By ordering this article number, you will receive a reconditioned wishbone with newly pressed-in bearings. The calculated replacement deposit will be returned to you as soon as the old part has been received and checked. This item is also available with race bearings (85 shore).article number FVD 341 017 07at the reconditioning process includes full inspection of each track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. If your old part is not repairable we will inform y...(choose a part on the right to read more)
$462.13
Make a selection FVD375003 Are you experiencing vibrations in the cabin? The most likely cause is a worn transmission mount. Severely worn mounts translate to engine component wear and can even cause difficulty shifting. Our mount is manufactured in europe by an OEM supplier using the finest materials. It is a 65 shore rubber hardness value which is the same as the what was standard on these cars. Be sure to swap yours out during your next service. Sold individually. Central fitment in transmission carrier 96437502301. 1 qty. Required. Tech tip: now is the time to replace the old hardware as well. Below is a list of what is needed for installation. 1 qty. Hex head bolt m10x100 90007429202 1 qty. Lock nut m10 49020001 2 qty. Washers 10.3x...(choose a part on the right to read more)
$178.20
Make a selection 96410524707ST This fits 964 c2 / c4 and rs models with engine codes # m64.01/02/03. This is an OEM part, sourced directly from Germany. Professional installation is required. Different manufacturing tolerances require an inspection of the free clearance of all parts! If you're not sure about what parts are right for your build, be sure to ask one of our parts specialists. Sold individually. 1 necessary per car.
$1,523.02
Make a selection 44404480062 High quality polished center console set that includes a polished carbon handbrake, the upper switch and lower switch covers made ready for installation. Each piece is a carbon overlay, meant to be adhered to your original plastic trim covers. We recommend adhering the carbon overlays to your originals with würth bond and seal (sold separately).
$1,577.66
Make a selection 1588501000 Originally published by floyd clymer this is a faithful reproduction of the 1967 publication of that manual. Includes complete technical data, service and maintenance information and comprehensive detailed instructions for the repair and overhaul of all major and minor mechanical and electrical components. Covers the Porsche 356-356a-356b-356c series from 1948 through 1965, making it an invaluable resource for collectors and restorers of these classic automobiles. There are separate sections that deal with the repair and overhaul procedures for the engine, ignition system, fuel system, clutch, transmission, rear suspension, steering, front suspension, brakes, shocks, heater and exhaust plus a detailed electrica...(choose a part on the right to read more) General FitmentACCESSORY
$49.14
Make a selection 129T851852 The rh turbo style Porsche wheel is a classic design perfectly suited for any Porsche model. The center section is cast aluminum and finished in a silver paint. The wheels come with standard rh center cap and accept factory Porsche wheel bolts and center caps. The wheels are offered in 17 and 18 with a variety of offsets to fit narrow and wide body Porsche applications. These wheels are made to order and take between 1-3 weeks to deliver. We recommend ordering a set of rh valves, part # 12945281 when ordering this wheel. Please note: if you are installing these on a 928, body work will be required. Sold individually.
$369.47
Make a selection 930602015AX3ATK Send us your distributor and we will remanufacture it for you. A perfect option for those who have time and want to save on costs. The remanufacturing process includes full inspection, disassembly, cleaning and degreasing. We then install a toothed timing belt, 3 German made top bearings, 1 German made lower bearing and a distributor pinion pin (part # 930 602 922 00). Clearances, timing and proper operation are then checked to ensure reliability. Please note: each distributor is remanufactured in Germany, so the lead times can vary.
$1,552.92
Make a selection 96434101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for...(choose a part on the right to read more)
$462.13
Make a selection 96434307281ATK Looking for a more cost-effective solution than ordering a new link? Let us recondition your original drop link. The reconditioning process includes full inspection, disassembly, degreasing and media blasting. Once fully prepared, we properly install new bushings, finish with a corrosion proof coating and include a new lock nut. Please note: each link is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your link we will notify you as soon as we can. Arrangements can be made for its return to you. Sold individually. 1 necessary per car.
$210.28
Make a selection 93064130201GEB Remanufactured part sourced in Germany. Includes a new rubber sealing ring. Purchase a newly remanufactured unit from us and an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and resell-able, the core deposit will be refunded. Sold individually. 1 necessary per car. Please note: this is a special-order item. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis. Please call us in advance of placing your order, these are very hard to come by and in some instances, we c...(choose a part on the right to read more)
$2,175.23
Make a selection 96433102100RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$725.87
Make a selection FVD35199623B Wheel spacers make your tires and wheels appear wider by moving the wheel out from the hub, providing both performance and appearance improvements. Whether you want improved handling, increase safety, or simply desire your car to make a statement about your individual style, wheel spacers can help you accomplish your goal. FVD BrombacherGermany conveniently combines Porsche specific h&r spacers, the correct Porsche bolt shoulders and the correct length h&r bolts to take the guess work out of adding spacers to your car. Our spacers are cost competitive and have been developed to work together without compromise. Don't be fooled by the competition whose costs quickly add up by requiring you to order the spacers...(choose a part on the right to read more)
$128.30
Make a selection BES99125020SK No need for Porsche sport exhaust (pse) envy with this muffler! This offers weight savings and a far more exotic sound than the pse, all without drone. It is the perfect compromise for you and your loved ones. Rich, deep, turbo motorsport tones with the valves open and soft subtle, completely stock sounds with them closed. Top of the line or range depending on the english and is the best choice for a daily driver. Features: - + 16 crank hp & + 15 crank torque. - weighs 37 lbs. (17 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - direct bolt on replacement for the factory center muffler. - includes necessary installation hardware. - reduces turbo lag, backpressure and thermal lo...(choose a part on the right to read more)
$5,275.91
Make a selection AP958170 Agency power is proud to release its super sport exhaust system for the 958 Porsche Cayenne s v8 2011 and up. the super sport exhaust is a axle system that gives your 4.8l v8 engine a real aggressive tone. made here in the usa, the exhaust saves close to 30lbs off the rear end of the vehicle. using 304 stainless steel and detail oriented tig welding, the exhaust system uses two small high flow mufflers which give it the sports car rumble. its reduced back pressure design gives the engine improved horsepower and torque with most noticeable improvement in throttle response. because of the reduced restriction, this exhaust horsepower gains can definitely be noticed in the mid to top rpm range.
$1,615.63
Make a selection BBI9963010001 The bbi autosport Porsche 996/997 turbo clutch slave cylinder conversion kit is a direct replacement part that eliminates the problematic factory power-assist system for improved reliability and pedal feedback. The factory power-assisted clutch system has always been the achilles heel for the Porsche 997 turbo. Utilizing the power steering system to help reduce the force needed to depress the clutch pedal, it is a flawed design that delivers a mushy pedal feel with poor feedback, and is highly prone to failure.
$1,436.40
Make a selection BK7032 Originally published by floyd clymer this is a faithful reproduction of the 1969 publication of that manual. By far the most comprehensive manual ever published for the 912 Porsche it includes complete technical data, service and maintenance information and comprehensive detailed instructions for the repair and overhaul of all major and minor mechanical and electrical components, making it an invaluable resource for collectors and restorers of these classic automobiles. There are separate sections that deal with the repair and overhaul procedures for the engine, ignition system, fuel system, clutch, transmission, rear suspension, steering, front suspension, brakes, heater, exhaust and emission control system pl...(choose a part on the right to read more) General FitmentACCESSORY
$43.15
Make a selection FVD34791130 Enhance steering precision and steering feedback by simply replacing your original tie rods. Turbo tie rods use a spherical inner joint instead of soft rubber bushings. They offer quicker steering response, more sensitivity and more precision. These are standard length we highly recommend them for lowered vehicles with bump steer kits like part # FVD34791100 or FVD347911930 . We also offer turbo tie rods in longer lengths for other applications, check part # FVD34791180r and FVD34791181ry this kit is manufactured in Germany by an OEM supplier, made from high carbon steel and 7075 t6 aluminum. Kit includes: 2 qty. Outer tie rods 2 qty. Inner tie rods 2 qty. Spacing washers 2 qty. Boots 2 qty. Castle nuts 2 qty. ...(choose a part on the right to read more)
$240.02
Make a selection 96442422300 Restore precise shifting with this OEM shift coupler bushing. To save on installation cost / time, we recommend installing a new conical screw, part # 90142422900 coupler sleeves / boots, part # 91142429400 and 91142429200 be sure to check / replace the shift rod bushing as well, part # 91142413900, the friction ring, part # 91442422400 this is a high-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per car.
From $6.05
Make a selection 96434705804SP We are committed to Porsche cars and are very happy to release an inner tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 032 00. We also suggest replacing your outer tie rods, part # 96434703200 (qty. 2 are needed) and now is also a good time to replace your worn out inner tie rod dust bellows, part # 96434719103. Please note: this is not for the ...(choose a part on the right to read more)
$212.65
Make a selection 96534703200SP We are committed to Porsche cars and are very happy to release an outer tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM part number, 965 347 032 00. Sold individually. 2 needed per car. We also suggest replacing your inner tie rod, we have a uniball option, our part # 96434705805sp (qty. 1 is needed) and now is also a good time to replace your worn out inner tie...(choose a part on the right to read more)
$272.05
Make a selection 99661298100 Let your wipers remember when to wipe the rain away. This great sensor automates the wipers into motion in this easy do-it-yourself kit. The only hard part of this installation is running the wiring from the rain sensor behind the rear view mirror to the relay box by the drivers left foot.
$454.79
Make a selection BES99305040S FVD is proud to introduce our newest line of Brombacherexhaust systems. Brombacher exhausts are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredible value. All of our exhausts are manufactured in Germany and are tested comprehensively for flow rate and characteristics, thermal stress, resistance to cracking, and longevity. Brombacher mufflers outer shell dampens and eliminates unwanted frequencies and ensures no resonance or drone in the cabin. The end result is a strong, linear, firing-order dominated flat-6 Porsche sound. In addition, Brombacherexhausts systems are available for ultimate performance full titanium. Our titanium system's are nearly...(choose a part on the right to read more)
$1,966.14
Make a selection FVD123014ATK K-16/24 turbo (up to 555hp) power is focused on low and mid range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD brombachers 993 k-16/24 remanufactured turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The remanufacturing process starts with re-profiling the OEM turbocharg...(choose a part on the right to read more)
$3,214.73
Make a selection BK7081 The haynes manual is the world's best selling vehicle repair manual. Hundreds of pictures with easy to follow step-by-step instructions make any repair a snap! Everything from a simple tune-up to a major engine overhaul are included in these handy manuals. The electrical wiring diagrams as great too. Specify make, model and year for your car or motorcycle. General FitmentACCESSORYBOXSTER 1997-04
$29.16
Make a selection F6464120010 Instrument faces are one of the most visible and frequently looked at components in your Porsche. When making the decision to change them you want to make ensure that you select a high quality product similar to your originals. Each of our sets are made in Germany and use the factory scripting (font). Our faces also offer the same uniform night time shading and includes the original die cut notches for easy installation. Each kit is made for global distribution, so simply pick out the faces that match your originals. They are available in a variety of colors to make a bold statement, or to match exterior paint schemes. This kit includes faces for: manual transmission / tiptronic transmission / kph / mph / celsi...(choose a part on the right to read more)
$652.21
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |