PORSCHE 964 PARTSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 356 1950-59 - Electrical (includes uncategorized and accessory items) 93060201501 Complete distributor without an exchange. This distributor has been completely remanufactured, which includes a full inspection, disassembly, cleaning and degreasing. We then install a toothed timing belt, 3 German made top bearings, 1 German made lower bearing and a distributor pinion pin (part # 930 602 922 00). We also install new dust caps, Bosch rotors and Bosch cap. Clearances, timing and proper operation are then checked to ensure reliability.
$2,533.99
Make a selection 90151107321 This is the rear release cable for the rear engine deck lid. It is 1900 mm in length. When replacing this cable, we also recommend replacing the handle, part # 90155281320 and the grommet, part # 91151253100. Also, check your rear lid lower lock, part # 90151205200, perfect time to replace it if it is corroded and the spring is worn. Sold individually. 1 necessary per car.
From $9.98
Make a selection 930105043021 This is an OEM part, sourced directly from Germany. Sold individually. 12 necessary per car.
$169.40
Make a selection 90110534403 High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually.
From $6.60
Make a selection FVD307964993 Make your next service a breeze with our pre-packaged service kits. Quality means everything to us, so we only source these parts directly in Germany. This kit contains: 1 qty. Tiptronic transmission filter 1 qty. Transmission filter sealing ring 1 qty. Transmission pan gasket 1 qty. Aluminum sealing ring 14x8 please note: this kit does not contain fluid!
$117.88
Make a selection 64461280100 This is a great quality part for any restoration project on your 356's and also fits early 912's. New genuine o.e.m. Quality 12 pole fuse box with brass insert, that support the ceramic style fuses. These are o.e.m. Specs, all brass fittings, specially grooved in the middle of the brass insert to have the end of the fuse tip sit snug on the brass, avoiding any movement or malfunction. Comes with new screws to tighten each individual brass insert, for your wiring, 24 in total. The cap fits just right with a chrome tightening knob, just like the original one, right on the top. View/Change Diagram
$7.93
Make a selection 90110554604 High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per car.
From $90.20
Make a selection 911561023602EQ This is a complete cabrio top cover made in Germany with original material. It is as close to the original as possible and is cut and trimmed to fit perfectly. Includes all of the original tenax snaps / retainers in the original locations. This would replace original part # 911 561 023 603 av made in Germany. Sold individually. 1 necessary per car. Please note: if you have a 1978-85 model please see our part # 911561023003eq
$1,237.50
Make a selection 9115550551550EQ Quality replacement headliner for original number, 911 555 055 155 00. This is made by dansk, they offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality, factory fitment and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Sold individually. 1 necessary per car.
$249.70
Make a selection 93010314715SET Oem parts, sourced directly from Germany. Sold individually. 1 necessary per car.
$112.20
Make a selection 91156128100R01 Genuine part sourced from Porsche ag in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. Like new
$42.01
Make a selection KEV53100600 Made in europe by one of the manufacturers to Porsche. Extremely high-quality kevlar / carbon door that includes every detail for a perfect fit. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight 6.4 kg (14.1 lbs) - kevlar / carbon - mounting is just like factory, no modifications are necessary. - includes inner protection bar please note: these are high quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world. Hinges are not provided; original hinges must be used. Please let us know the year and model and if you intend to use electric windows and electric mirrors.
$3,473.80
Make a selection 96455525100NEQ Attention to detail is what distinguishes our parts from the competition. We source these door handles in Germany to ensure that they are made as closely to the original as possible. Sold individually.
$99.94
Make a selection 964555251000EQ Attention to detail is what distinguishes our parts from the competition. We source these door handles in Germany to ensure that they are made as closely to the original as possible. Sold individually.
$95.46
Make a selection 96410440180 Motorsports item. Sold individually. All motorsport and racing parts are special order items. Special order items must be paid for in advance. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis and do not carry any warranty. No exceptions.
$22.00
Make a selection 96420713004EQ This connects to the side of the oil tank. We recommend replacing 2 qty. Clamps, part # 99951235602 when replacing this piece. Sold individually. 1 necessary per car.
$11.00
Make a selection 96411122380R02 All motorsport and racing parts are special order items. Special order items must be paid for in advance. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis and do not carry any warranty. No exceptions. Leichte lagerspuren
$201.99
Make a selection KEV53100500 Made in europe by one of the manufacturers to Porsche. Extremely high-quality kevlar / carbon door that includes every detail for a perfect fit. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight 6.4 kg (14.1 lbs) - kevlar / carbon - mounting is just like factory, no modifications are necessary. - includes inner protection bar please note: these are high quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world. Hinges are not provided; original hinges must be used. Please let us know the year and model and if you intend to use electric windows and electric mirrors.
$3,473.80
Make a selection 96442422300 Restore precise shifting with this OEM shift coupler bushing. To save on installation cost / time, we recommend installing a new conical screw, part # 90142422900 coupler sleeves / boots, part # 91142429400 and 91142429200 be sure to check / replace the shift rod bushing as well, part # 91142413900, the friction ring, part # 91442422400 this is a high-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per car.
From $5.88
Make a selection FVD211343 Already replaced your heater blower tube with a carbon bypass? This carbon / kevlar air duct will match the engine decor perfectly. It is a replica of the factory rs lightweight factory air duct. This is a quality tuning product manufactured by dansk. They offer a complete line of tuning and performance parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment manufacturers (oem) to Porsche in Germany. This installs easily and really dresses up the engine. Sold individually. 1 necessary per car.
$267.30
Make a selection KEV53100601 Made in europe by one of the manufacturers to Porsche. Extremely high-quality kevlar / carbon door that includes every detail for a perfect fit. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight 4 kg (8.81 lbs) - kevlar / carbon - mounting is just like factory, no modifications are necessary. ** does not include the inner protection bar please note: these are high quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world. Hinges are not provided; original hinges must be used. Please let us know the year and model and if you intend to use electric windows and electric...(choose a part on the right to read more)
$3,285.70
Make a selection 96434101707AT By ordering this article number, you will receive a reconditioned wishbone with newly pressed-in bearings. The calculated replacement deposit will be returned to you as soon as the old part has been received and checked. This item is also available with race bearings (85 shore).article number FVD 341 017 07at the reconditioning process includes full inspection of each track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. If your old part is not repairable we will inform y...(choose a part on the right to read more)
$418.00
Make a selection HEI964001009S Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long-standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: bolt-in bar - screwed in to the original seat belt points. Aluminum 1.5-inch diameter tubing, .098 wall thickness tubing. Bars which connect to the main hoop, use a connecting joint system. Black paint finish. We recommend adding the harness bar, part # hei600036s to your order as it is sold al...(choose a part on the right to read more)
$1,604.90
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |